• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.35-38
• /
• 2005

Carbon fiber sheets are widely used for strengthening the deteriorated RC structures. However most studies on the strengthening method of RC structures with carbon fiber sheets are concerning static problems. The purpose of this experimental study is to present the basic data on fatigue behaviors of. RC beams strengthened with carbon fiber sheets. The experimental parameters of this study are ; 1) the existence of U-shaped carbon fiber sheets at the ends for anchoring, 2) the number of carbon fiber sheet layers in strengthening the RC beams, 3) the load levels of $60\%\~90\%$ of the static bending moment strength, which is obtained form the static tests. Experimental results are estimated from the relationships of load level, displacement, number of repeated load and released energy. It is concluded that U-shaped carbon fiber sheets for end anchoring is very effective and the beams strengthened with one layer of carbon fiber sheet have longer fatigue life than that with three layers.

• Journal of Aerospace System Engineering
• /
• v.6 no.2
• /
• pp.28-34
• /
• 2012

Structural integrity evaluation is important item in the aircraft certification. Recently, it is designed for limit load, material weakness about fatigue and corrosion, damage by bird strike in flight to evaluate structural integrity of aircraft. And static/fatigue analysis are performed to secure structural integrity, it was verified by static and fatigue tests. To evaluate the structural integrity of small aircraft tail, structural integrity was calculated by the finite element analysis. In the present study, finite element analysis are performed to pick out load cases in flight occurrence, and secure margin of safety to evaluate structural integrity of KC-100 tail unit. The proprieties of finite element analysis results are compared with the static structure test results. The estimation process of structural integrity for small aircraft tail may help the design.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1679-1688
• /
• 2008

Recently, the bogie frame weight of Light Rail Transit system has been reduced in order to save energy and materials. However, this light weighted vehicle structure is very important to verify the fatigue strength at the development stage. Bogie system consists of bogie frame, suspensions, wheel-sets, braking system and transmission system. Among these components, the bogie frame is most significant component subjected to the whole vehicle and passenger loads. In this study, the bogie frame for the New LRT power car is evaluated to the static and fatigue strength. And the evaluation method is used the LRT Performance Test Standards Specification throughout the FEM analysis and static load test. The static and fatigue test results for the LRT bogie frame of power car has been appeared very safety and stable for the design load conditions.

• Journal of the Korean Society of Safety
• /
• v.27 no.5
• /
• pp.42-48
• /
• 2012

Peel-tension fatigue experiments were conducted for investigating on fatigue strength of mechanical press joints of SPCC steel sheet used in the field of the automobile industry. In addition, finite element method analysis on the peel-tension specimen was conducted using HyperMesh and ABAQUS softwares. The cold rolled mild steel was used to join the T-shaped peel-tension specimen with a button diameter of 5.4 mm and a punch diameter of 8.3 mm. The fatigue limit load amplitude was found to be 112.4 N at the number of cycles 106, indicating that the ratio of fatigue limit load to static peel-tension strength was about 8%. This value suggests that the mechanical press joint is highly vulnerable to peel-tension load rather than to tensile-shear load, considering that the ratio of fatigue limit load to static tensile-shear strength was about 43%. Fatigue failure mode was found to be interface-failure mode.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.11-18
• /
• 2007

A laboratory investigation was conducted to characterize the flexural fatigue behavior of high performance fiber reinforced cement mortar. Five specimens for statics flexural test and fourteen specimens for the flexural fatigue test were made based on the fiber mixing ratio. Static flexural tests were firstly performed to obtain magnitudes of static failure loads and stress levels before flexural fatigue tests. The flexural fatigue behaviors were investigated based on the stress level and fiber mixing ratio. Also, the equations for the interrelation of the flexural fatigue stress levels with the number at loading cycle were proposed.

• The Journal of Korean Physical Therapy
• /
• v.30 no.2
• /
• pp.63-66
• /
• 2018

Purpose: The purpose of the current study was to examine the effects of exercise-induced fatigue of the plantar flexor muscle in the dominant ankle on the plantar flexor strength and postural control function of the contra-lateral side. Methods: Twenty-one young adults (male: 10, female: 11) volunteered to participate in this study. An exercise-induced fatigue protocol to induce fatigue was performed in the plantar flexor of the dominant ankle. For the fatigue protocol, the participants were instructed to raise their heels as high as possible in the position with one leg stance of the dominant lower limb, and the heel was then downed after holding for 1 second. The muscle strength of the contra-lateral plantar flexor was measured using a digital muscle strength test device, and the static and dynamic postural control were tested by acquiring the center of gravity velocity while performing one leg standing. A paired t-test was used to identify the differences between the pre- and post, and the data were analyzed using SPSS 12.0 software. Results: Comparison of the pre- and post-test data revealed a significant difference in the plantar flexor strength and dynamic postural control after exercise-induced muscle fatigue in the dominant side. On the other hand, there was no significant difference in the static postural control. Conclusion: These findings have practical implications, suggesting that unilateral muscle fatigue affects the ankle muscle strength and postural ability of the contralateral side.

• Journal of Korean Institute of Industrial Engineers
• /
• v.6 no.1
• /
• pp.27-38
• /
• 1980

This paper presents the validation of a stochastic model of muscle fatigue during static muscle contractions. Forty four laboratory experiments, covering eleven test conditions for two trained subjects, were run in order to estimate fatigue and recovery rates, based on EMG observations. The validation of the model was made by comparing the model predictions to the experimental fatigue time. The validation study supports that the stochastic model of muscle fatigue accurately represents the underlying fatigue process. The study also provides support that the fatigue model can be used as a monitor of individual muscle capabilities.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.1-6
• /
• 2015

Self-piercing riveting (SPR) is receiving more recognition as a possible and effective solution for joining automotive body panels and structures, particularly for aluminum parts and dissimilar parts. In this study, static strength and fatigue tests were conducted using coach-peel and cross-tension specimens with Al-5052 plates for evaluation of fatigue strength of the SPR joints. For the static experiment results, the fracture modes are classified into pull-out fracture due to influence of plastic deformation of joining area. During the fatigue tests for the coach-peel and cross-tension specimens with Al-5052, interface failure mode occurred on the top substrate close to the rivet head in the most cycle region. There were relationship between applied load amplitude $P_{amp}$ and life time of cycle N, $P_{amp}=715.5{\times}N^{-0.166}$ and $P_{amp}=1967.3{\times}N^{-0.162}$ were for the coach-peel and cross- tension specimens, respectively. The finite element analysis results for specimens were adopted for the parameters of fatigue lifetime prediction. The relation between SWT fatigue parameter and number of cycles was found to be $SWT=192.8N_f^{-0.44}$.

• Composites Research
• /
• v.12 no.3
• /
• pp.26-35
• /
• 1999

The static strength and fatigue life of repaired graphite/epoxy laminates are observed using tensile coupon. The lay-up of investigated laminates was [$0^{\circ}$/$\pm$$45^{\circ}$/$90^{\circ}$]$_s$. Static strength was measured from the specimens prepared by various repair techniques such as precured-single patch, precured-double patch and cure-in-place methods. The strength was recovered to the extent of 60~80 % of unnotched case. Fatigue life was also measured from the laminates repaired with cure-in-place method. Hwang and Han's MFLPE 1(modified fatigue life prediction equation 1), which was based on the fatigue modulus degradation model and reference modulus, was chosen for fatigue life prediction of repaired specimen and compared with the conventional fatigue life equation such as S-N curve and Basquin's relation. The MFLPE 1 has better agreement with experimental data than S-N curve and Basquin's relation.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.3
• /
• pp.453-461
• /
• 2002

This study investigated the fatigue stength of non-load carrying cruciform welded joints, which was maunfactured using the SM570 and POSTEN80 high strengh steel. Factors such as fatigue strength, fatigue crack initiation and propagation, thickness effect, and the relatioinship between the static strength and the fatigue strength were examined and compared with previous fatigue testing results. Results showed that the fatigue strength of SM570 and POSTEN80 steel are higher than the grade represented on the design specification. It is also identified the size effect and the dependence of the static stength in a few cases.