• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.369-374
• /
• 2006

This paper describes dynamic characteristics of a power transmission tower consisting of lots of power lines and insulators. A numerical 3D modeling for the static, dynamic and buckling analyses of the power transmission tower is presented considering the case when the power lines are cut. Eigenvalue analysis indicates that the transmission tower shows different behavior comparing to usual structures governed by several low modes. The transmission tower is governed by lots of modes. It is verified that the transmission tower is structurally safe against the static wind and buckling loads. But the structural and buckling safety is not guaranteed when all power lines are cut, which comes to collapse the transmission tower. Further study is in need to overcome such case. Wind dynamic analysis shows that fluctuating wind loads increase the response of the tower.

• Earthquakes and Structures
• /
• v.20 no.2
• /
• pp.215-224
• /
• 2021

The carbon dioxide present in the atmosphere is one of the main reasons for the corrosion of bridges, buildings, tunnels, and other reinforced concrete (RC) structures in most industrialized countries. With the growing use of fossil fuels in the world since the Industrial Revolution, the amount of carbon dioxide in urban and industrial areas of the world has grown significantly, which increases the chance of corrosion caused by carbonation. The process of corrosion leads to a change in mechanical properties of rebars and concrete, and consequently, detrimentally impacting load-bearing capacity and seismic behavior of RC structures. Neglecting this phenomenon can trigger misleading results in the form of underestimating the seismic performance metrics. Therefore, studying the carbonation corrosion influence on the seismic behavior of RC structures in urban and industrial areas is of great significance. In this study, a 2D modern RC moment frame is developed to study and assess the effect of carbonation corrosion, in 5-year intervals, for a 50 years lifetime under two different environmental conditions. This is achieved using the nonlinear static and incremental dynamic analysis (IDA) to evaluate the reinforcement corrosion effects. The reduction in the seismic capacity and performance of the reinforced concrete frame, as well as the collapse probability over the lifetime for different corrosion scenarios, is examined through the capacity curves obtained from nonlinear static analysis and the fragility curves obtained from IDA.

• Structural Engineering and Mechanics
• /
• v.14 no.4
• /
• pp.473-489
• /
• 2002

A static linear programming formulation for minimum weight design of frames that is based on a matrix displacement method is presented in this paper. According to elementary theory of plasticity, minimum weight design of frames can be carried out by using only the equilibrium equations, because the system is statically determinate when at an incipient collapse state. In the present formulation, a statically determinate released frame is defined by introducing hinges into the real frame and the bending moments in yield constraints are expressed in terms of unit hinge rotations and the external loads respectively, by utilizing the matrix displacement method. Conventional Simplex algorithm with some modifications is utilized for the solution of linear programming problem. As the formulation is based on matrix displacement method, it may be easily adopted to the weight optimization of frames with displacement and deformation limitations. Four illustrative examples are also given for comparing the results to those obtained in previous studies.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.241-245
• /
• 2012

In this study, one type of circular shaped composite tube was used, combined with reinforcing foam and without foam. Furthermore, CFRP (Carbon Fiber Reinforced Plastic) circular member manufactured from CFRP prepreg sheet for lightweight design. CFRP is an anisotropic material which is the most widely adapted lightweight structural member. The crashworthy behavior of circular composite material tubes subjected to static axial compression under same conditions is reported in this paper. The collapse mode during the failure process were observed and analyzed. The behavior of polymeric foams to the tubes crashworthiness were also investigated.

• Structural Engineering and Mechanics
• /
• v.48 no.5
• /
• pp.681-695
• /
• 2013

Performance-based seismic design allows a structure to develop inelastic response during earthquakes. This modern seismic design requires more clearly defined levels of inelastic response. The ultimate deformation of a structure without total collapse (target displacement) is used to obtain the inelastic deformation capacity (inelastic performance). The inelastic performance of a structure indicates its performance under excitation. In this study, a new energy-based method to obtain the target displacement for reinforced concrete frames under cyclic loading is proposed. Concrete structures were analyzed using nonlinear static (pushover) analysis and cyclic loading. Failure of structures under cyclic loading was controlled and the new method was tested to obtain target displacement. In this method, the capacity energy absorption of the structures for both pushover and cyclic analyses were considered to be equal. The results were compared with FEMA-356, which confirmed the accuracy of the proposed method.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.44-46
• /
• 2002

Service restoration following a complete or partial collapse starts with reenergize a transmission line from black-start generators. Voltage problems can arise by Ferranti effect as unloaded transmission line is reenergized. This paper presents analytical results on the primary restorative transmission system focused on the voltage problem during the early restoration process. Methodologies to handle load pick-up compensating Ferranti effect. and terminal voltage and reactive capability limitation of black-start generators about self-excitation are presented. An algorithm for static analysis about these methodologies is developed, and EMTDC simulation for verifying the efficiency of the algorithm is performed.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.145-148
• /
• 1992

The best index should show the margins to the operating limit at the present operating point without much efforts. Such voltage collapse proximity index has been proposed in this study. Differently from the normal procedure in which every bus load is increased at the same propotion, bus load increase toward the direction of T/L loss increase has been applied in this study. Sample studies show the usefulness and the practical applicability in voltage stability analysis.

• Structural Engineering and Mechanics
• /
• v.9 no.2
• /
• pp.111-126
• /
• 2000

Truss type structures are attractive to a variety of engineering applications on earth as well as in space due to their high stiffness to mass ratios and ease of construction and fabrication. During the service life, an individual member of a truss structure may lose load carrying capacity due to many reasons, which may lead to collapse of the structure. An analytical and computational procedure has been developed to study the response of truss structures subject to member failure under static and dynamic loadings. Emphasis is given to the dynamic effects of member failure and the propagation of local damage to other parts of the structure. The methodology developed is based on nonlinear finite element analysis technique and considers elasto-plastic material nonlinearity, postbuckling of members, and large deformation geometric nonlinearity. The pseudo force approach is used to represent the member failure. Results obtained for a planar nine-bay indeterminate truss undergoing sequential member failure show that failure of one member can initiate failure of several members in the structure.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.1
• /
• pp.127-136
• /
• 2016

The purpose of this research is to conduct a comparative study on the characteristics of daily volatility spillovers across the stock markets of Korea, China, and Japan. We employ generalized spillover definition and measurement developed by Diebold & Yilmaz (2009, 2012). The sample period is January 5, 1993 to September 25, 2015. From a static full-sample analysis, we find that 8.60% of forecast error variance comes from volatility spillovers. From a 250-day rolling-sample analysis, we discover that there exist significant volatility fluctuations in the stock markets of Korea, China and Japan, expecially during the Asian Financial Crisis (1998-1999) and the US Credit Crisis (2008-2009) after the collapse of Lehman Brothers. From the net directional spillovers across three countries, we come upon that there is neither a definite leader nor a significant follower during the sample period.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.144-147
• /
• 2011

본 논문에서는 기존의 선형정적해석 절차를 변형하여 부재의 이력모델 응용을 통해 부재 파괴여부에 따라 힌지처리 및 재해석의 반복과정을 자동으로 수행하는 새로운 연쇄붕괴 프로그램을 제안하였다. 6m 4경간의 철근콘크리트 골조에 철골 가새를 보강 설치한 예제구조물에 대하여 최하층 기둥부재를 제거한 후 기존 해석법과 제안 해석법을 통해 선형정적해석을 수행하였고, 그 결과를 비교 분석하였다. 해석 결과, 두 절차 간 부재단위의 파괴여부 및 구조물 힌지 분포 경향의 동일함을 보여 해석의 신뢰성을 확보하였으며. 기존 해석법에 비해 수행단계의 시간이 매우 짧고 자동 반복해석으로 인한 오류의 가능성도 최소화 할 수 있음을 확인하였다.