• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.141-147
• /
• 2015

Gas foil thrust bearings (GFTBs) have attractive advantages over rolling element bearings and oil film thrust bearings, such as oil-free operation, high speed stability, and high-temperature operation. However, GFTBs have lower load carrying capacity than the other two types of bearings owing to the inherent low gas viscosity. The load carrying capacity of GFTBs depends mainly on the compliance of the foil structure and the formed hydrodynamic wedge, where the gas pressure field is generated between the top foil and the thrust runner. The load carrying capacity of the GFTBs is very important for the suitable design of oil-free turbomachinery with high performance. The aim of the present study is to identify the characteristics of the load carrying performance of GFTBs. A new test rig for the experimental measurements is designed to provide static loads up to 800 N using a pneumatic cylinder. The maximum operating speed of the driving motor is 30,000 rpm. A series of experimental tests—lift-off test, static load performance test, and maximum load capacity test—estimate the performance of a six-pad GFTB, in terms of the static load, driving torque, and temperature. The maximum load capacity is determined by increasing the static load until the driving torque rises suddenly with a sharp peak. The test results show that the torque and temperature increase linearly with the static load. The estimated maximum load capacity per unit area is approximately 80.5 kPa at a rotor speed of 25,000 rpm. The test results can be used as a design guideline for GFTBs for realizing oil-free turbomachinery.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 기술교육전문연구회
• /
• pp.3-7
• /
• 2003

Usually, the thrust is calculated by magnetic equivalent circuit modelling method for thrust capacity and accuracy progress of position control about a Linear Pulse Motor of which position precision is good and open-loop control is possible within Linear Motors. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of Motor. So this study wants to compare and analyze measurement data and calculating data of the static force of Linear Pulse Motor. and then we can get more accuracy method, calculating the static thrust of Linear Pulse Motor(LPM).

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.414-416
• /
• 2009

In order to build a transient simulation program for a high thrust liquid rocket engine(LRE), a static performance simulation program for components were made. The components were the thrust chamber (combustion chamber and supersonic nozzle), centrifugal pump (impeller and volute casing), impulse turbine, and flow control devices (control valve and orifice). Simplified mathematical models based on classical thermodynamic and inviscid theories were used to remove complexity and enhance the utility of the program. We examined the results of each program qualitatively for validate each component modeling.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.43-45
• /
• 1994

This paper proposes the new method to calculate the static thrust and normal force of a hybrid type double-sided linear pulse motor by the coenergy which considered the magnetic nonlinealities. In the process of the computation, the nonlinear characteristics of the magnetic material were interpolated by the cubic spline method. And, to investigate the characteristics of the hybrid type DLPM, the static thrust and the normal force is shown as a function of displacement, input current and air airgap length. Also the simulation values are compared with the experimental ones obtained from a hybrid type DLPM.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.913-914
• /
• 2017

액체로켓엔진 개발 과정에서 중량을 절감하고 구조 신뢰성을 증가시키기 위해서는 엔진 시스템에 대한 구조 해석이 필요하다. 발사체는 비행 중 자세제어를 위해 엔진의 TVC (thrust vector control) 구동기의 변위를 변화시켜 연소기를 회전하여 추력의 방향을 제어한다. 본 연구에서는 연소기 김발을 하는 75톤급 액체 로켓 엔진에 대하여 TVC 구동 전/후의 정적 구조 해석을 수행하고 비교하였다.

• 대한전기학회논문지
• /
• 제43권5호
• /
• pp.753-760
• /
• 1994

This paper proposes a new method to compute the static thrust of a hybrid-type LPM by the coenergy method, which can be applied to a nonlinear programming of the optimization techniques for the optimal design. In the process of the computation, the magnetic nonlinearities of the permanent magnet, the primary and the secondary core are interpolated by the cubic spline method. And then, the equivalent magnetic circuit including the airgap reluctance which is a function of the displacement is modelled by the permeance method. The static thrust which is a derivative of the coenergy is computed by the Newton Raphson method at each displacement. To verify this proposed method, the results of the compjutation are compaction with those of the experiment obtained from the DLPM with 2 phase and 4 poles.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.993-996
• /
• 1993

This paper presents the static thrust of a hybid-type LPM by coenergy method. First, the nonlinealities of the permanent magnet, the primary core and the secondary are interpolated by the cubic spline method. Then the equivalent magnetic circuit including airgap reluctance, which is a function of displacement, modelled by the permeance method is obtained. From the derivative of coenergy with displacement computed by Newton Raphson method, the static thrust is calculated at each displacement with certain exciting current.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.91-101
• /
• 1986

This paper deals with the effect of static and dynamic cuttig force and the behaviour of drill life in drilling process. The experiments are performed with cemented carbide drills and high speed steel drills of 10mm in diameter and in an annealed SM45C. The conclusions are as follows (1) Dynamic cutting force is varied with the dept of hole. (2) Dynamic cutting forces of torque and thrust are increase with the increase in feed and cutting speed. (3) Chipping influence the dynamic cutting force of thrust than torque, and in the case of thrust, the amplitude is 3-7 times large than ordinary cutting state. (4) Prediction of drill life can be obtained from more easily the amplitude of static cutting force than that of dynamic cutting force.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.332-341
• /
• 2020

High-speed turbomachinery implements gas foil bearings (GFBs) due to their distinctive advantages, such as high efficiency, lesser part count, and lower weight. This paper provides the test results of the static structural stiffnesses and loss factors of bump-type foil thrust bearings with increasing preload and bearing deflection. The focus of the current work is to experimentally quantify variability in structural stiffnesses and loss factors among the four test thrust bearings with identical design values and material of the bump and top foil geometries using the same (open-source) fabrication method. A simple test setup, using a rigidly mounted non-rotating shaft and thrust disk, measures the bearing bump deflections with increasing static loads on the test bearing. The inner and outer diameters of the test bearings are 41 mm and 81 mm, respectively. The loss factor, best-representing energy dissipation in the test bearings, is estimated from the area inside the local hysteresis loop of the load versus the bearing deflection curve. The measurements show that structural stiffnesses and loss factors of the test bearings significantly rely on applied preloads and bearing deflections. Local structural stiffnesses of the test bearings increase with applied preloads but decrease with bearing deflections. Changes of loss factors are less sensitive to applied preloads and bearing deflections compared to those of structural stiffnesses. Up to 35% variability in static load structural stiffnesses is found between bearings, while up to 30% variability in loss factors is found between bearings.

• Structural Engineering and Mechanics
• /
• 제53권2호
• /
• pp.325-336
• /
• 2015

This paper presents a study based on the damage due to the fatigue life of thrust ball bearings using vibratory analysis. The main contribution of this work lies in establishing a relation between modal damping and the rolling contact fatigue damage of the thrust ball bearing. Time domain signals and frequency spectra are extracted from both static and dynamic experiments. The first part of this research consists in measuring the damping of damaged thrust ball bearings using impact hammer characterization tests. In a second part, indented components representing spalled bearings are studied to determine the evolution of damping values in real-time vibration spectra using the random decrement method. Dynamic results, in good agreement with static tests, show that damping varies depending on the component's damage state. Therefore, the method detailed in this work will offer a possible technique to estimate the thrust ball bearing fatigue damage variation in presence of spalling.