• Steel and Composite Structures
• /
• 제42권3호
• /
• pp.407-426
• /
• 2022

Superior to traditional welded studs, high strength friction-grip bolted shear connectors facilitate the assembling and demounting of the composite members, which maximizes the potential for efficiency in the construction and retrofitting of new and old structures respectively. Hence, it is necessary to investigate the structural properties of high strength friction-grip bolts used in steel concrete composite beams. By means of push-out tests, an experimental study was conducted on post-installed high strength friction-grip bolts, considering the effects of different bolt size, concrete strength, bolt tensile strength and bolt pretension. The test results showed that bolt shear fracture was the dominant failure mode of all specimens. Based on the load-slip curves, uplifting curves and bolt tensile force curves between the precast concrete slab and steel beam obtained by push-out tests, the anti-slip performance of steel-concrete interface and shear behavior of bolt shank were studied, including the quantitative analysis of anti-slip load, and anti-slip stiffness, frictional coefficient, shear stiffness of bolt shank and ultimate shear capacity. Meanwhile, the interfacial anti-slip stiffness and shear stiffness of bolt shank were defined reasonably. In addition, a total of 56 push-out finite element models verified by the experimental results were also developed, and used to conduct parametric analyses for investigating the shear behavior of high-strength bolted shear connectors in steel-concrete composite beams. Finally, on ground of the test results and finite element simulation analysis, a new design formula for predicting shear capacity was proposed by nonlinear fitting, considering the bolt diameter, concrete strength and bolt tensile strength. Comparison of the calculated value from proposed formula and test results given in the relevant references indicated that the proposed formulas can give a reasonable prediction.

• Tribology and Lubricants
• /
• 제23권3호
• /
• pp.123-129
• /
• 2007

This paper presents a theoretical model for the analysis of double-bumped AFBs. The stiffness and damping coefficients of the double bump vary depending on the external load and its friction coefficient. In the case of a lightly loaded condition where only the upper bump contributes to deformation, the double bump is in the single active region. In the case of a heavily loaded condition where both the upper and lower bumps contribute to deformation, the double bump is in the double active region. So the double bump can be either in the single or double active region depending on vertical deflection. The equivalent stiffness and damping coefficients of the bump system are derived from the vertical and horizontal deflection of the bump, including the friction effect. A static and dynamic performance analysis is carried out by using the finite difference method and the perturbation technique. The results of the performance analysis for a double-bumped AFB are compared with those obtained for a single-bumped AFB. This paper successfully proves that a double bumped AFB has higher load capacity, stiffness, and damping than a single-bumped AFB in a heavily loaded condition.

• 대한조선학회논문집
• /
• 제47권4호
• /
• pp.580-588
• /
• 2010

OPB(out-of-plane bending)-induced failure of mooring chain was firstly addressed by CALM (catenary anchor leg mooring)-type offloading buoy, located approximately one mile away from the bow of the Girassol FPSO which was installed offshore area of Angola in September 2001. This study deals with verifying the load transfer mechanism between the first free chain link and connected two chain links inside the chain hawse. OPB moment to angle variation relationships are proposed by extensive parametric study where the used design variables are static friction coefficients, proof test loads, nominal tension forces, chain link diameters, chain link grades and chain link types. The stress ranges due to OPB moments are obtained using nonlinear FEAs (finite element analyses). Final stress ranges are derived considering ones from IPT (in-plane tension) forces. Also a formula for OPB fatigue assessment is briefly introduced.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.578-585
• /
• 2000

Geometrical characteristics of fresh red pepper(Capsicum annuum L.) were measured and indexed to define some important geometrical characteristics, and malformation of body and fruit stalk which are necessary for the design of the equipments for cutting, spreading and alignment of red pepper in developing a fruit stalk remover of fresh red pepper. The effects of bending of body and fruit stalk on the equipments of cutting, spreading and alignment were studied. The maximum lengths of some parts of fresh red pepper were found to be 180 mm, 125 mm, 144 mm, 67 mm and 76 mm for the body, the bent part of body, the fruit stalk, the bent part and the straight part of fruit stalk, respectively. The fresh red pepper with bending indices more than 0.4 and 0.3 for the body and the fruit stalk, respectively, was defined to be malformed based on the result of cutting rate using cutting unit; while the other ones to be normal in shape. Based on this, among the total fresh red peppers tested, 47%, 40% and 20% were found malformed for the body, the fruit stalk, and for both of the body and the fruit stalk. Malformed red peppers were poorer in spreading and alignment than normal ones, and the processed quantity was decreased with increased feed rate. The required time for the malformed peppers to pass on the alignment plate inclined at 30 increased rapidly at 8.3 Hz with increased feed rate. For the fresh red peppers with average moisture content of 85%,w.b., the maximum tensile strength between fruit stalk and body was 88.1 N; the maximum cutting resistances were 92.1 N and 94.9 N for the fruit stalk-calyx joint and body, respectively. Average coefficients of static friction were 0.99, 0.62, 0.59 and OJ, respectively, for the surfaces of rubber, galvanized iron, acryl and plywood.

• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.421-430
• /
• 1997

본 연구에서는 숏브라스트한 후 무기징크 페인트로 도장한 무기징크면, 연마면, 흑피면에 대하여 정적 및 피로시험을 수행하여 기존의 연구결과와 비교평가함으로써 마찰면의 표면상태에 따른 고장력볼트 마찰이음부의 정적 및 피로거동을 규명하고자 하였다. 본 연구의 목적을 달성하기 위하여 일련의 정적 및 피로시험을 실시하고 토크관리법의 타당성 평가, 미끄러짐계수의 도출, 도입축력의 감소률 규명, 피로강도의 평가, 마찰면의 압축력 분포 조사 등을 수행하였다. 본 실험결과와 기존 연구자들의 연구결과를 종합적으로 검토한 결과 볼트의 설계축력 도입을 위한 토크관리법은 타당하며, 시간경과 및 반복하중의 작용에 따른 축력감소율을 고려할 때 설계축력의 110%로 초기축력을 도입하도록 규정한 시방서 기준은 적합한 것으로 평가되었다. 시간경과에 따른 도입축력의 초기감소율은 경과시간의 상용로그에 비례하는 것으로 나타났으며, 도입직후 약 20시간이 경과하면 일정한 값으로 수렴되고 있음을 알 수 있었고 이들은 마찰면의 표면조도와는 상관관계가 없는 것으로 평가되었다. 미끄러짐계수는 연마면, 무기징크프라이머 도포면, 흑피면 순으로 크게 나타났으며 미끄러짐하중은 도입축력에 크게 좌우되나 도입축력이 크면 마찰면의 표면조도의 손상으로 인하여 미끄러짐계수가 작아져 도입축력과 미끄러짐하중 사이에는 선형적 비례관계가 성립되지 않음을 알 수 있었다. 마찰면의 압축력 분포를 조사한 결과 내측볼트 주변의 마찰면적이 외측볼트 주변보다 응력방향에 있어서 더 넓게 분포하고 있는 것을 알 수 있었으며, 이는 외측볼트로부터 마찰접합에서 지압접합으로 천이되고 있는 것으로 판단된다.

• Journal of the Korean Wood Science and Technology
• /
• 제16권3호
• /
• pp.48-64
• /
• 1988

This study was carried out to investigate the free vibrational properties of traditional and replaceable species for sounding board, using piezoelectrical accelerometer and signal analyzer. In the study, the frequency equations of free-free beam carrying a concentrated mass in the transverse vibration and of free-mass beam in the longitudinal vibration were used. The results obtained were as follows. 1. Average values of dynamic modulus of rigidity of Korean commercial species measured were as follows. Paulownia tomatosa (Thunb.) Steudel: $5.590\times10^9\;dyne/cm^2$ Tilia amurensis Rupr.: $5.414\times10^9\;dyne/cm^2$ Macckia amurensis Rupr.: $10.044\times10^9\;dyne/cm^2$ Fraxinus mandshurica Rupr.: $8.876\times10^9\;dyne/cm^2$ Ulmus davidiana var.japonica Nakai: $8.677\times10^9\;dyne/cm^2$ Pinus rigida Miller: $6.33\times10^9\;dyne/cm^2$ Fraxinus rhynchophylla Hance: $4.666\times10^9\;dyne/cm^2$ 2. The ratio of dynamic transverse Young's modulus to dynamic modulus of rigidity, $E_T/G_{LT}$, was 24.922 for Fraxinus rhynchophylla Hance, which was the highest, 7.317 for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. 3. The value of longitudinal dynamic Young's modulus was about 3.7% and 19.8%, respectively, higher than those of transverse dynamic and static Young's modulus. The value of transverse dynamic Young's modulus was about 15.5% higher than that of static Young's modulus. 4. Predicted value of MOR in terms of correlation coefficient by transverse dynamic Young's modulus was slightly higher than that of static Young's modulus, but no significance was found out. 5. Transverse dynamic Youne's modulus was $(2.002\pm0.288)\times10^{11}\;dyne/cm^2$ for Fraxinus mandshurlca Rupr., which was the highest, $(0.601\pm0.100)\times10^{11}\;dyne/cm^2$ for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. The sound velocity of sitka spruce was 5,685 m/sec, which was the highest. 6. Internal friction of Paulownia tomentosa (Thunb.) Steudel was shown the lowest value among Korean commercial species, $(8.795\pm1.795)\times10^{-3}$, but was higher than that of sitka spruce, $(7.331\pm0.991)\times10^{-3}$. Internal friction was shown negative correlation with density and dynamic Young's modulus, respectively. 7. K value was affected largely by internal friction and was the highest, $2.225\times10^8$ for Paulownia tomentosa (Thunb.) Steudel and was the lowest, $0.550\times10^8$ for Fraxinus rhynchophylla Hance. K value of Paulownia tomentosa (Thunb.) Steudel was higher than that of sitka spruce and K values of melapi and cottonwood, which have been considered to be replaceable species with sitka spruce in the piano industry, were lower than those of Paulownia tomentosa (Thunb.) Steudel and mill amurensis Rupr.

• 한국표면공학회지
• /
• 제25권6호
• /
• pp.309-317
• /
• 1992

Evaluation of electroplated gold has been carried out to obtain the data base for electrical, mechanical and environmental properties for telecommunication component applications. Gold plating was performed to a various thickness of $0.1\mu\textrm{m}$ to 1.$25\mu\textrm{m}$ after Ni plating of $3\mu\textrm{m}$ on C52100 bronze. Electrical properties were evaluated by measuring contact resistance using 4-wire method under static contact and dynamic contact during wear. Reciprocating wear test was performed to study the wear behavior as well as failure of gold contacts. Environmental characteristics were evaluated by using salt spray testing and SO2 test. Hardness of soft gold film was measured to be 53KHN under 5g load. Friction coefficient was initially obtained to be 0.15 and 0.25 under 100g and 200g loads respectively, and then raised up to 0.8 with increasing reciprocating wear cycles. Static contact resistance was 2 to 3m$\Omega$ regardless of gold film thickness while drastic changes of contact resistance were occured upon stripping of the gold film during wear. The lifetime of contact wear showing stable contact resistance increased up to 6 times for $1\mu\textrm{m}$ thickness compared to that of$ 0.1\mu\textrm{m}$ thickness under 100g load. All gold plating appeared to be stable under salt atmosphere while only the gold plating over 1$\mu\textrm{m}$ was stable under SO2 atmosphere.

• 한국기계가공학회지
• /
• 제19권10호
• /
• pp.87-97
• /
• 2020

In general, tires require various sensors and power supply devices, such as batteries, to obtain information such as pressure, temperature, acceleration, and the friction coefficient between the tire and the road in real time. However, these sensors have a size limitation because they are mounted on a tire, and their batteries have limited usability due to short replacement cycles, leading to additional replacement costs. Therefore, vibration energy harvesting technology, which converts the dynamic strain energy generated from the tire into electrical energy and then stores the energy in a power supply, is advantageous. In this study, the output voltage and power generated from piezoelectric elements are predicted through finite element analysis under static state and transient state conditions, taking into account the dynamic characteristics of tires. First, the tire and piezoelectric elements are created as a finite element model and then the natural frequency and mode shapes are identified through modal analysis. Next, in the static state, with the piezoelectric element attached to the inside of the tire, the voltage distribution at the contact surface between the tire and the road is examined. Lastly, in the transient state, with the tire rotating at the speeds of 30 km/h and 50 km/h, the output voltage and power characteristics of the piezoelectric elements attached to four locations inside the tire are evaluated.

• Journal of Biosystems Engineering
• /
• 제40권3호
• /
• pp.201-211
• /
• 2015

Purpose: Designing equipment for processing, sorting, and other post-harvest operations of agricultural products requires information about their physical properties. This study was conducted to investigate some of the mechanical and physical properties of Moringa oleifera L. pods and seeds. Methods: Properties such as the length, width, thickness, bulk density, porosity, mass, static coefficient of friction, and angle of repose were determined as a function of moisture content. Statistical data and force-deformation curves obtained at each loading orientation and moisture level were analyzed for bioyield point, bioyield strength, yield force, rupture point, and rupture strength using a testrometric machine. Result: The basic dimensions (length, width, and thickness) of moringa pods and seeds were found to increase linearly from 311.15 to 371.45 mm, 22.79 to 31.22 mm, and 22.24 to 29.88 mm, respectively, in the moisture range of 12 to 49.5% d.b. The coefficient of friction for both pods and seeds increased linearly with an increase in moisture content on all the surfaces used. The highest value was recorded on mild steel, with 0.581 for pods and 0.3533 for seeds, and the lowest on glass for pods, with a value of 0.501, and of 0.2933 for seeds on galvanized steel. The bioyield and rupture forces, bioyield and rupture energies, and deformation of the pods decreased with an increase in moisture content to a minimum value, then increased with further decrease within the moisture content range, while the yield force increased to a maximum value and then decreased as the moisture content increased. Conclusion: These results will help to determine the most suitable conditions for processing, transporting, and storing moringa pods, and to provide relevant data useful in designing handling and processing equipment for the crop.

• 한국안전학회지
• /
• 제22권5호
• /
• pp.13-20
• /
• 2007

Elastomeric O-ring seals are widely used in static and dynamic applications. A compressed and highly pressurized O-ring seal inserted under laterally one-sided constrained condition has been analyzed experimentally and numerically. The deformed shape and extrusion length of the O-ring under high pressure has been measured by the computed tomography. Through the comparison of experimental and FE results, the numerical analysis technique has been verified. Using verified FE method, the contact stress profiles at sealing surfaces have been investigated and their relevance to the 0-ring performance evaluated based on stress-related and displacement-related parameters. It has been found that the contact stress profiles and deformation behaviors of the seal are affected by friction coefficient, gap clearance, and pressure considerably.