• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1798-1802
• /
• 2007

Adhesion strength of single layer ceramic capacitor sheet was measured using a peel testing system developed in this study. The peel test specimens with various dimensions were prepared from the ceramic sheet cast on the PET film. In peel test, the sheet specimen was adhered on the glass jig floating on the liquid media, which was designed to minimize the friction, and the specimen was then pulled up by micro-actuator. During the separation of the sheet from the PET film, peel force was measured. To normalize the testing condition, 3 different widths of the specimen were selected: 5, 10 and 20 mm. was used Furthermore, testing speed effect was investigated in this study. From the resullts using various testing conditions, the standard method for the peel strength testing may be suggested. Based on the testing condition, effect of peel angle on the strength was experimentally examined. It was found that the adhesive strength for the ceramic sheet is nearly identical, irrespective of the specimen width ranged from 5 to 20 mm, while the adhesive strength was increased with increasing testing speed. Furthermore, the strength was shown to be dependent on the peel angle.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.10
• /
• pp.2348-2356
• /
• 1997

This paper describes a method of AAL(SSCOP) protocol conformance testing and its result analysis in ATM network. Terminal equipment(TE) that implements protocols for connecting ATM network shall be verified if appropriately implement by conformance testing. The protocol specifications and the testing methodology are recommended or standardized by international standardization organization(ITU-T, ISO, etc.). The ATM AAL (SSCOP) protocol which selected for describing conformance test procedure is standardized in ITU-T Q.2110 and ATM Forum UNI 3.1 which are same in contents. Also Testing standard like ATS for SSCOP is specified in ATM Forum 95-1459R2. Construction of conformance testing environment is necessary to coordinate in relations with standards, then testing must beexecuted at that environment and the results from the test system analyzed. For this, it is necessary to select any test case from standard for testing and to make ETS. The ETS is proted on the test system and conformance testing will execute on that system. Finally the result from the test system is to analyze. This conformance testing procedure is applicable to the same other test cases in SSCOP and protocols in any communcation networks.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.247-252
• /
• 2008

Systems architecture of information models for construction industry is introduced. The architecture ful fills international standards, such as ISO 10303(STEP) and IAI IFC, etc. It is defined in web service description language(WSDL) and ISO 10303-11(EXPRESS) language. A standard platform for this standard architecture is also developed. This platform has several tools which can transform EXPRESS description file into C++ or Java languages and which also can generate an IDL file or OWL file from an EXPRESS file. System architects, software engineers, information system consultants can use these standards to define their information model for construction industry in standardized way. Construction engineers can test this information model with ease using standard testing tools and testing method, which is also a part of standard architecture of information systems for virtual construction.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.8 no.2
• /
• pp.42-47
• /
• 2012

The containment local leakage rate testing in nuclear power plants is performed in accordance with ANSI/ANS 56.8-1994 in Korea. Two methods, the make-up flow rate and the pressure decay, are used for local leakage rate testing. Though ANSI/ANS 56.8-1994 does not define clearly the minimum test duration for the make-up flow rate method, it requires obtaining the data after reaching the stable condition. Thus the prerequisite stable condition for data acquisition and the testing time is differently applied to each NPPs. Therefore, this study presents a standardized test procedure for data stabilization and testing time through experiments to improve the test reliability.

• Journal of Advanced Navigation Technology
• /
• v.19 no.2
• /
• pp.91-97
• /
• 2015

This paper specifies several considerations about assessing safety-critical software in the aerospace domain. In order to evaluate safety critical software in the aerospace industry, it is required to identify an information of evaluation criteria of software under evaluation. The information is specified in the standard, but determination of evaluation criteria cannot be decided by itself and depends on the results of safety assessment of a system and system design. Thus, this paper explains required information of system development standard and safety assessment standard to determine software evaluation criteria. It surveys existing methodologies about evaluating software, and suggests method which is adapted to evaluation of an advanced surface movement guidance and control system (A-SMGCS) software.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.33-37
• /
• 2001

Recently, the HFPD measurement testing is widely used in partial discharge measurement of HV machines because HFPD measurement testing receives less influence of external noise and has a merit of good sensitivity. Also HFPD testing is able to offer the judgement standard of degradation level of HV machine and can detect discharge signals in live-line. Therefore it is very useful method compare to previous conventional PD testing method and effective diagnosis method in power transformer that requires live-line diagnosis. But partial discharges have very complex characteristics of discharge pattern so it is required continuous research to development of precise analysis method. In recent, the study of partial discharge is carrying out discover of initial defect of power equipment through condition diagnosis and system development of degradation diagnosis using HFPD(High Frequency Partial Discharge) detection. In this study, simulated transformer is manufactured and HFPD occurred from transformer is measured with broad band antenna in real time, the degradation grade of transformer is analyzed through produced patterns in simulated transformer according to applied voltages.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.8
• /
• pp.1948-1957
• /
• 1996

The conformance testing of communication protocol is the process to evaluate whether the protocol implemented is identified with standard specification. By evaluating how generated test cases detect many faults, it can be used with standard estimating efficiency of conformance testing. The method that evaluates the capability of fault coverage for test cases, has been researched by mathematical analysis and simulation. In this paper, we pointed out the problem of existing method and proposed new evaluation model of fault covergage for test case which generated by foult model. Also, we analyzed the results comparing to the existing evaluation method and proved its validity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.04a
• /
• pp.20-23
• /
• 1990

In order to evaluate the difference of testing results in the standards on the compressive strength of various countries, we have compared the testing results of the compressive and flexural strength, one of the most important properties of cement, obtained on the various standards(KS, JIS, BS, ASTM) and the statistical method was used to evaluate the results.

• Journal of Computing Science and Engineering
• /
• v.2 no.3
• /
• pp.274-300
• /
• 2008

Software testing cost can be reduced if the process of testing is automated. However, the test data generation task is still performed mostly by hand although numerous theoretical works have been proposed to automate the process of generating test data and even commercial test data generators appeared on the market. Despite prolific research reports, few attempts have been made to evaluate and characterize those techniques. Therefore, a lot of works have been proposed to automate the process of generating test data. However, there is no overall evaluation and comparison of these techniques. Evaluation and comparison of existing techniques are useful for choosing appropriate approaches for particular applications, and also provide insights into the strengths and weaknesses of current methods. This paper conducts experiments on four representative test data generation techniques and discusses the experimental results. The results of the experiments show that the genetic algorithm (GA)-based test data generation performs the best. However, there are still some weaknesses in the GA-based method. Therefore, we modify the standard GA-based method to cope with these weaknesses. The experiments are carried out to compare the standard GA-based method and two modified versions of the GA-based method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.6
• /
• pp.427-439
• /
• 2006

Accurate estimates of in place thickness of early age (3 to 28 days after casting) concrete pavements are needed, where a thickness accuracy of ${\pm}6mm$ is desired. The impact-echo method is a standardized non-destructive technique that has been applied for this task. However, the ability of impact-echo to achieve this precision goal is affected by Vp (measured) and ${\beta}$ (assumed) values that are applied in the computation. A deeper understanding of the effects of these parameters on the accuracy of impact-echo should allow the technique to be improved to meet the desired accuracy goal. In this paper, the results of experimental tests carried out on a range of concrete slabs are reported. Impact-echo thickness estimation errors caused by material property gradients and sensor type are identified. Correction factors to the standard analysis method are proposed to correct the identified errors and to increase the accuracy of the standard method. Results show that improved accuracy can be obtained in the field by applying these recommendations with the standard impact-echo method.