• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.336-345
• /
• 2001

The construction of underwater structures has been increased, but underwater concrete hassome problems of quality deterioration and contamination around in-situ of civil and architecture; therefore, new materials and methods for them are demanded. In this paper in-situ application of underwater antiwashout concrete which is manufactured for trio purpose of not only decreasing suspended solids and the heat of hydration but also increasing long term strength was studied. In the case of mock-up test(Ⅰ), when underwater antiwashout concrete, whose slump flow was 58 cm, was placed in the mock-up test at a speed of 24 ㎥/hr, it took about a minute to flow to the side wall, and the surface was maintained at horizontal level. In this case, compressive strength of the core specimens in each section was higher than the standard design compressive strength of 240 kgf/㎠. In the case of mock-up test(II), pH value and suspended solids of high strength underwater antiwashout concrete were 10.0∼11.0 and 51 mg/ℓ at 30 minutes later, initial and final setting time were about 30, 37 hr, and the slump flow of that was 53$\pm$2 cm. In the placement at a speed of 27 ㎥/hr, there was no large difference in flowing velocity, with or without reinforcement and flowing slope was maintained at horizontal level. In this case, compressive strength and elastic modulus of the core specimens somewhat decreased as flowing distance was far : however, those of central area showed the highest value.

• Journal of the Korea Concrete Institute
• /
• v.26 no.6
• /
• pp.687-694
• /
• 2014

This study established a displacement ductility ratio model for ductile design for the boundary element of shear walls. To determine the curvature distribution along the member length and displacement at the free end of the member, the distributions of strains and internal forces along the shear wall section depth were idealized based on the Bernoulli's principle, strain compatibility condition, and equilibrium condition of forces. The confinement effect at the boundary element, provided by transverse reinforcement, was calculated using the stress-strain relationship of confined concrete proposed by Razvi and Saatcioglu. The curvatures corresponding to the initial yielding moment and 80% of the ultimate state after the peak strength were then conversed into displacement values based on the concept of equivalent hinge length. The derived displacement ductility ratio model was simplified by the regression approach using the comprehensive analytical data obtained from the parametric study. The proposed model is in good agreement with test results, indicating that the mean and standard deviation of the ratios between predictions and experiments are 1.05 and 0.19, respectively. Overall, the proposed model is expected to be available for determining the transverse reinforcement ratio at the boundary element for a targeted displacement ductility ratio.

• Tunnel and Underground Space
• /
• v.27 no.3
• /
• pp.132-145
• /
• 2017

Shock loss was not applied for the tunnel ventilation of road tunnel in the past. However, pressure losses due to the shock loss can be significant in network double-deck road tunnel in which combining and separating road structures exist. For the optimum ventilation design of network double-deck road tunnel, this study conducted 3D CFD numerical analysis for the shock loss at the combining and separating flows. The CFD model was made with the real-scale model that was the standard section of double-deck road tunnel. The shock loss coefficient of various combining and separating angles and road width was obtained and compared to the existing design values. As a result of the comparison, the shock loss coefficient of the $30^{\circ}$ separating flow model was higher and that of the two-lane combining flow model was lower. Since the combining and separating angles and road width can be important for the design of shock loss estimation, it is considered that this study can provide the accurate design factors for the calculation of ventilation system capacity. In addition, this study conducted 3D CFD analysis in order to calculate the shock loss coefficient of both combining and separating flows at flared intersection, and the result was compared with the design values of ASHRAE. The model that was not widened at the intersection showed three times higher at the most, and the other model that was widened at the intersection resulted two times higher shock loss coefficients.

• Journal of Korean Society of Transportation
• /
• v.35 no.3
• /
• pp.234-246
• /
• 2017

The Seoul metropolitan government introduced the bus information systems, bus rapid transit to increase travel speed and punctuality but still suffer from insufficiency. This paper delivers a study verifying the external factors at near the bus stops. The dependent variable was set to the standard deviation of (1) travel time and (2) travel time to and from the bus stop in this study. The independent variables were set to (1) the number of routes, (2) traffic volume by bus type, (3) the number of bus bays, (4) the possibility of passing, (5) the distance to crosswalks and intersections, and (5) the presence of residential road. The results showed that the most significant factors included the link section speed, number of bus bay, distance to crosswalk, and the possibility of passing.

• The Journal of Pediatrics of Korean Medicine
• /
• v.31 no.1
• /
• pp.52-62
• /
• 2017

Objectives The purpose of this study is to review pre-existing clinical practice guidelines for autism spectrum disorders, and refer those in developing a new practice guideline. Methods A total of 9 existing clinical practice guidelines for autism spectrum disorder developed from 2010 to 2016 were searched by Google scholar and Pubmed, and were reviewed those literatures in three parts: general, diagnosis & evaluation, and intervention. Results There were no consistency in the recommendation methods of 9 clinical care guidelines (such as the method of rating and recommendation intensity for diagnosis, evaluation, and treatment). However, in the diagnosis and evaluation section, frequently used evaluation and diagnostic tools are mentioned in most clinical practice guidelines, and the types of pharmacologic and non-pharmacological treatments that are mainly recommended in treatment are equally mentioned in most clinical practice guidelines could confirm. Conclusions 1. Some guideline recommendations are graded according to each criterion. Recommendations presented in various databases were based on systematic reviews or other literatures. The most utilized database were PsycINFO, CINAHL, Cochrane. 2. DSM-5 and ICD-10 were the most common used diagnostic criteria, and DSM-IV was used as a diagnostic standard in the guideline published before 2013. The tools used for diagnosis and evaluation were also varied. However, most recommended ones were ADI-R, ADOS-G, and DISCO. 3. Treatment was largely divided into pharmacological intervention and non-pharmacological intervention. In some guideline, the interventions were divided into pediatric and adult. Most of the pharmacological interventions were not recommended due to lack of evidence, but in cases in which specific symptoms were aimed, they recommended to seek professional help. 4. In addition to interventions, each guideline referred to supportive interventions that may be helpful in the daily life of patients with ASD, which may need to be addressed in future clinical guidelines.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.5
• /
• pp.77-89
• /
• 2008

The bikes are conflicted with the cars and the pedestrian at the intersection and the road with the bike crossing. To establish the bike signal at this section is one method to solve this conflict. According to the survey for the bike road status and the biker's characters which are crossing the road at the intersection, the bike crossing are established with beside the pedestrian crossing and most of the bikers are crossing the street by the pedestrian signal. Also, the bike queue which is waiting the signal change at the stop line was cleared before the closing the pedestrian signal. Considering the result of this survey, TOUCAN crossing signal type in England for bike signal at the place where the bike crossing are established with beside the pedestrian crossing, in which bike rider and pedestrian can cross by the pedestrian signal operation, is suggested. However, at the place where the bike crossing is apart from the pedestrian crossing, the bike signal which is connected to the vehicle signal is suggested. All these types of bike signals can be accepted for the present bike crossing equipments and the biker's characters and be adapted to the police standard traffic signal controller by adjusting the signal time only without any function change.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.279-286
• /
• 2019

In this study, an experimental study on the tensile properties of steel fiber-reinforced ultra high strength concrete(UHSC) with a standard compressive strength of 180MPa was performed. Steel fibers with a volume ratio of 1% were mixed to prepare direct tensile strength specimens and prism specimens for the three-point bending test. The fabricated specimens were set up in the middle section of the specimen to induce cracks, and the test was carried out according to each evaluation method. First, the stress-strain curves were analyzed by performing direct tensile strength tests to investigate the behavior characteristics of concrete after cracking. In addition, the load-CMOD curve was obtained through the three-point bending test, and the inverse analysis was performed to evaluate the stress-strain curve. Tensile behavior characteristics of the direct tensile test and the three-point bending test of the indirect test were similar. In addition, the tensile stress-strain curve modeling presented in the SC structural design guidelines was performed, and the comparative analysis of the measured and predicted values was performed. When the material reduction factor of 1.0 was applied, the predicted value was similar to the measured value up to the strain of 0.02, but when the material reduction factor of 0.8 was applied, the predicted value was close to the lower limit of the measured value. In addition, when the strain was greater than 0.02, the predicted value by SC structural design guideline to underestimated the measured value.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.6
• /
• pp.659-677
• /
• 2022

Hydrogen is emerging as a next-generation energy source and development and supply of FCEV (hydrogen fuel cell electric vehicle) is expected to occur rapidly. Accordingly, measures to respond to hydrogen car accidents are required and researches on the safety of hydrogen cars are being actively conducted. In this study, In this study, we developed a hydrogen car accident scenarios suitable for domestic conditions for the safety evaluation of hydrogen car in road tunnels through analysis of existing experiments and research data and analyzed and presented the hazard distance according to the accident results of the hydrogen car accident scenarios. The accident results according to the hydrogen car accident scenario were classified into minor accidents, general fires, jet flames and explosions. The probability of occurrence of each accident results are predicted to be 93.06%, 1.83%, 2.25%, and 2.31%. In the case of applying the hydrogen tank specifications of FCEV developed in Korea, the hazard distance for explosion pressure (based on 16.5 kPa) is about 17.6 m, about 6 m for jet fire, up to 35 m for fireball in road tunnel with a standard cross section (72 m²).

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.333-342
• /
• 2021

In this study was conducted to measure the water content and dry unit weight of the ground using TDR (Time Domain Reflectometry) in order to supplement the problems of the conventional compaction management method. The Flat TDR system is a device that does not cause ground disturbance, and in order to verify the measured values, the dry density and water content were measured for samples of the ground subject at 7 sites other than Jumunjin Standard Temple. The water content section was divided into 6 sections of 3, 6, 9, 12, 15, and 18%, and the experimental results were confirmed according to the unified classification method. As a result of the indoor experiment, the water content showed an error of about 0.7% for the SP sample and about 1.3% for the SM sample. In addition, the dry unit weight confirmed an error of about 7% for the SP sample and about 5% for the SM sample. It was confirmed that stable values were derived in sandy or silty sandy ground except for clay or gravel. Through the experimental results, it was confirmed that the measured values of the flat TDR system derive similar values to the existing traditional compaction management method, and it was determined that the flat TDR equipment was suitable for construction sites that require quick constructability and economic feasibility.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.208-215
• /
• 2021

In this study, a customiz ed bridge system was developed for North Korea application. For the application of North Korea, the customized bridge system design, fabrication, and construction performance evaluation were performed using ultra-high performance concrete a compressive strength 120MPa or more and a direct tensile strength 7MPa or more. The comparison of the North Korean truck luggage load(30, 40, 55) and the Korean standard KL-510 load showed that cross-section increased as the load increased. Furthermore, a bridge with a span length of 30m was fabricated with ultra-high performance concrete for the construction performance evaluation. The evaluation of the load condition analysis was performed by a flexural test. The results showed that a bridge with a span length of 30m secured about 167% of sectional performance under initial cracking load conditions and about 134% of load bearing capacity under ultimate load conditions. As a result of economic analysis, the customized bridge system using ultra-high-performance concrete was less than about 11% of the upper construction cost compared to the steel composite girder bridge. Therefore, these results suggest that the price competitiveness can be secured when applying the ultra-high-performance concrete long-span bridge developed through this study.