• Wind and Structures
• /
• 제5권1호
• /
• pp.15-24
• /
• 2002

This paper reports the numerical calculations of uniform turbulent shear flow around a square cylinder. The predictions are obtained by solving the two-dimensional unsteady Navier-Stokes equations in a finite volume technique. The turbulent fluctuations are simulated by the standard $k-{\varepsilon}$ model and one of its variant which takes care of the realizability constraint in order to suppress the excessive generation of turbulence in a stagnation condition. It has been found that the Strouhal number and the mean drag coefficient are almost unaffected by the shear parameter but the mean lift coefficient is increased. The present predictions are compared with available experimental data.

• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.336-345
• /
• 1998

The substantial loss behind axial flow rotor was generated by wake, various vortices in the hub region and the leakage vortex in the tip region. Particularly, the leakage vortex formed near blade tip was one of the main causes of the reduction of performance, the generation of noise and the aerodynamic vibration in rotor downstream. In this study, the three-dimensional flowfields in an axial flow rotor for various tip clearances were calculated, and the numerical results were compared with the experimental ones. The numerical technique was based on SIMPLE algorithm using standard k-.epsilon. model (WFM). Through calculations, the effects of the tip clearance on the overall performance of rotor and the loss distributions, and the increase in the displacement, momentum, and blade-force-deficit thickness of the casing wall boundary layer were investigated. The mass-averaged flow variables behind rotor agreed well with the experimental results. The presence of the tip leakage vortex behind rotor was described well. Although the loci of leakage vortex by calculation showed some differences compared with the experimental results, its behavior for various tip clearances was clarified by examining the loci of vortex center.

• 동력기계공학회지
• /
• 제21권6호
• /
• pp.5-12
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was carried out to investigate the internal flow fields characteristics according to wind tunnel contraction type. The turbulence model used in this study is a realizable $k-{\varepsilon}$ modified from the standard $k-{\varepsilon}$ model. As a results, the distribution of the axial mean velocity components along the central axis of the flow model is very similar to the ASME and BE types, and the cubic and cosine types. When the flow passes through the interior space of the analytical models, the flow resistance at the inlet of the plenum chamber is the largest at BS type contraction, but the smallest at cubic type contraction. The boundary layer thickness is the smallest in the cosine type contraction as the axial distance increases. The maximum turbulent kinetic energy in the test section is the smallest in the order of the contraction of cubic type and cosine type. Comprehensively, cubic type contraction is the best choice for wind tunnel performance, and cosine type contraction can be the next best solution.

• Wind and Structures
• /
• 제24권5호
• /
• pp.465-480
• /
• 2017

Modelling an equilibrium atmospheric boundary layer (ABL) in computational wind engineering (CWE) and relevant areas requires the boundary conditions, the turbulence model and associated constants to be consistent with each other. Among them, the inflow boundary conditions play an important role and determine whether the equations of the turbulence model are satisfied in the whole domain. In this paper, the idea of modeling an equilibrium ABL through specifying proper inflow boundary conditions is extended to the SST $k-{\omega}$ model, which is regarded as a better RANS model for simulating the blunt body flow than the standard $k-{\varepsilon}$ model. Two new sets of inflow boundary conditions corresponding to different descriptions of the inflow velocity profiles, the logarithmic law and the power law respectively, are then theoretically proposed and numerically verified. A method of determining the undetermined constants and a set of parameter system are then given, which are suitable for the standard wind terrains defined in the wind load code. Finally, the full inflow boundary condition equations considering the scale effect are presented for the purpose of general use.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.115-120
• /
• 2011

A ribbed tube consumes more power to transport the fluid by comparing with flat one. After the tangential velocity component occurs, its contact area with the ribbed tube becomes large and it enables the effective energy transportation. The flow characteristics vary according to the geometry of tube rib. This study aims to investigate the flow characteristics of fluids working at Reynolds numbers of 20,000, 40,000, 60,000 and 80,000 with the air at $15^{\circ}C$ in the ribbed test tube high 1mm and wide 8.48mm. As the flow characteristics are included with the states of fully developed hydrodynamical region, axial velocity vector distribution and non-dimensional velocity distribution, they are shown with the physical validity.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.31-38
• /
• 2005

육상 수조식 양식장은 해수를 끌어들여 어류를 기르는 데 사용된다. 본 연구는 사각 수조 내의 다양한 기하학적 관계와 유동에 대한 유동 특성을 도출하였다. 수치해석은 유한 체적법과 SIMPLE 기수법은 수치해석법을 활용하였으며, 비압축성 유체와 3차원 표준 $k-{\varepsilon}$난류 모델을 적용하였다. 속도 분포, 온도 분포에 대한 정보를 확보하였다. 실험과 수치해석의 결과가 정성적으로 잘 일치함을 보였다. 양식장의 깊이가 증가함에 따라 바닥 쪽의 유동이 더욱 안정됨을 확인하였다. 이는 각종 배설물 등의 정체현상으로 연결될 수 있음을 확인하였다. 수조내의 온도는 유입구의 초기 온도가 중요하며, Re 수가 증가할수록 온도는 상승하고 유입구의 반대 벽면 근처의 온도가 유입구 보다 증가함을 알 수 있었다.

• 대한조선학회지
• /
• 제26권1호
• /
• pp.11-23
• /
• 1989

자유표면을 고려하지 않은 경우 선체주위의 3차원 점성유동을 수치해석하는 전산프로그램을 작성하였다. 복잡한 선체를 합리적으로 처리할 수 있는 body-fitted 좌표계를 사용하고, 난류모델은 $k-\varepsilon$모델을 채택하였다. Reynolds 방정식의 준 3차원 형태를 수치해석하도록 하였다. 작성된 전산프로그램의 합리성과 수치해석적 성능을 파악하기 위하여 단면이 3:1 타원단면의 모델과 SSPA-720 콘테이너 선형을 이용하여 수치해석의 결과와 실험데이터를 비교하였다. 평균속도분포와 압력의 분포는 위 모델의 풍동시험결과와 전반적으로 잘 일치하고 있으나, 난류운동에너지는 선미 부근에서 실제보다 많이 예측되고 있다.

• 한국산업보건학회지
• /
• 제10권2호
• /
• pp.140-149
• /
• 2000

In industrial field, there are several operations where a horizontal unidirectional airflow is used to control airborne contaminants. When a worker is immersed in a uniform freestream, a recirculating airflow can be created downstream of the worker by the phenomenon of boundary layer seperation. If the contaminant source and the breathing zone are within this near-wake region, high exposure may occur. The investigation for the effect of contaminant source location on worker exposure was performed by using CFD(Computational Fluid Dynamics). The airflow field was numerically calculated by assuming a steady flow and using the standard $k-{\varepsilon}$ turbulence model. As the results were compared with experimental data, the applicability of CFD was successfully verified. Subsequently, the breathing zone concentrations of the worker were predicted and compared with experimental data. The effects of contaminant density and turbulence intensity of freestream on worker exposure were evaluated.

• 한국산업보건학회지
• /
• 제19권3호
• /
• pp.240-249
• /
• 2009

HRSG(Heat Recovery Steam Generator) building is large enclosed structure included various heat sources. This building needs to appropriately keep internal air temperature for worker's safety and operability of control devices. In this study, ventilation analysis is performed to find proper ventilation method for temperature control. Ventilation analysis is applied to entire internal space of the building with standard $k-{\varepsilon}$ model and enhanced wall treatment because of large size of the structure. And the ventilation method is considered natural and forced convection with two louver structures which has damper or not. Louver structure affect directly air circulation in near HRSG and lower region of the building. Forced ventilation provides strong inertial force which cause upward airflow. From the analysis, it is found that design requirement for internal air temperature can be satisfied by forced ventilation method with louver structure without damper.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1940-1954
• /
• 1992

본 연구에서는 가공기 자체의 파라메터와 성능에 관한 연구로서 출력 에너지 가 서로 다른 가공기를 사용하여 SUS 304 스테인리스 시험편을 관통, 절단하면서 출력 에너지와 최대 출력을 비교하여 보고, 시험편 관통시 주파수와 출력 에너지와의 관계, 시험편 관통시 응융 금속 제거량에 의한 절단 속도의 예측, 서로 다른 출력의 가공에 있어서 슬릿 절단 폭, 커프 폭, 드로스 길이, 절단면의 표면 거칠기 등을 비교하여 출 력차에 따른 가공 특성을 고찰하였다.