• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.109-118
• /
• 2005

A concrete shear wall system is commonly adopted in high-rise residential apartment buildings. In the construction stage, a rectangular opening is often made for the convenience of horizontal movement of workers, and construction materials and equipment. In the case of safety or stability assessment of a shear wall, the cutout part can be a critical factor. Finite element method is adopted to investigate the elastic stability behavior of the perforated unit shear wall. The key analysis parameters are the cutout location and its size. The effect of out-of-plane bending and horizontal shear are also examined in the stability analysis.

• Journal of Environmental Health Sciences
• /
• v.38 no.2
• /
• pp.151-158
• /
• 2012

Objectives: Bioaerosols released by treating organic-waste resources cause a variety of environmental and hygiene problems. The objective of this study was to investigate the distribution characteristics of the airborne bacteria emitted from a pig manure composting plant, a principal site for organic-waste resource facilities. Methods: Three types of pig manure composting plant were selected based on fermentation mode: screw type, rotary type and natural-dry type. Each site was visited and investigated on a monthly basis between September 2009 and August 2010. A total of 36 air samplings were obtained from the pig manure composting plants. The air sampling equipment was a six-stage cascade impactor. Quantification and qualification of airborne bacteria in the air samples was performed by agar culture method and identification technique, respectively. Results: The mean concentrations of airborne bacteria in pig manure composting plant were 7,032 (${\pm}1,496$) CFU $m^{-3}$ for screw type, 3,309 (${\pm}1,320$) CFU $m^{-3}$ for rotary type, and 5,580 (${\pm}1,106$) CFU $m^{-3}$ for natural dry type. The screw type pig manure composting plant showed the highest concentration of airborne bacteria, followed by the natural dry type and the rotary type. The ratio of respirable to total airborne bacteria was approximately 40-60%. The predominant genera of airborne bacteria identified were Micrococcus spp., Staphylococcus spp. and Escherichia spp. Conclusion: Monthly levels of airborne bacteria were highest in August and lowest in November regardless of fermentation mode. There was no significant correlation relationship between airborne bacteria and environmental factors such as temperature, relative humidity and particulate matters in pig manure composting plants.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.5
• /
• pp.163-167
• /
• 2020

Ring-shaped SiC (Silicon carbide) polycrystals used as an inner material in semiconductor etching equipment was manufactured using the PVT (Physical Vapor Transport) method. A graphite cylinder structure was placed inside the graphite crucible to grow a ring-shaped SiC polycrystal by the PVT method. The crystal polytype of grown crystal were analyzed using a Raman and an UVF (Ultra Violet Fluorescence) analysis. And the microstructure and components of SiC crystal were identified by a SEM (Scanning Electron Microscope) and EDS (Energy Disruptive Spectroscopy) analyses. The grain size and growth rate of SiC polycrystals fabricated by this method was varied with temperature variation in the initial stage of growth process.

• Journal of The Korean Association of Information Education
• /
• v.16 no.4
• /
• pp.483-488
• /
• 2012

As propagation of mobile smart devices is widespread, it is an observable trend that the cases of utilizing them are increasing in the school programs, and it is also anticipated that they will be very important part of the educational equipment in near future. For this reason the department of education and science technology has announced a medium and long term project on the education with smart device, which is undergoing the preparation stage, and the various academic and industrial institutes have actively produced the related research results and the application prototypes. In this paper we propose a framework on design and implementation of a visual context recognition system for educational purpose usable in the school program by utilizing a module for recognition of the texts embedded in the image captured by video camera from mobile smart device. The system proposed in this paper is consisted of the four modules, such as, image acquisition, image processing, information extraction, and knowledge representation, which are explained in details with the practical examples.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.9
• /
• pp.4347-4351
• /
• 2012

Background: Breast cancer is the most common cancer of women and the principal cause of death in middle aged women. The objective of this study was to describe the trend of breast cancer and its management in Aden and adjacent south-eastern governorates of Yemen during the last 20 years. Patients and Methods: This is a retrospective analysis of previous studies on patients with breast cancer in Aden and adjacent south-eastern governorates, Yemen (January 1989 through December 2007). The studied variables were: sex, age, time and type of presentation, disease stage, pathological types and the performed surgical treatment. The sources of information were the treatment registry of Aden health office, archives of Al-Gamhouria teaching hospital; major referral and other public and private hospitals in Aden and Aden Cancer Registry. Results: The total number of patients was 476, 99% being females. The age range was 19-88 years. The most affected age was 30-50 years (60.5%), 95% presenting after one month of having breast symptoms. Forty-five percent presented with signs of advanced local disease, while 59.2% had palpable axillary lymph nodes on presentation. Early breast cancer (stages I-II) occurred in 47%, and late breast cancer (stages III-IV) in 51.5%. Invasive ductal carcinoma was the commonest pathology (89.3%). The main surgical treatment was mastectomy (modified radical mastectomy (50%). Conclusion: Breast cancer is predominantly a disease of young with late presentation and advanced disease. Improving health awareness and earlier diagnosis of the disease by health education, encouraging breast self-examination, and providing the mammography equipment and mammary clinics in hospitals are recommended. Establishment of oncology and radiotherapy centers in Aden is a necessity.

• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.1-6
• /
• 2018

Reliability based design and assessment (RBDA) methodology is one of the newest directions of natural gas pipeline design method. Reliability targets are used to ensure that safety levels are met relevant limit states in the stage of design and maintenance. The target reliability for ultimate limit states such as large leak and rupture were developed using tolerable risk criteria for individual and societal risk. This paper shows the reliability target can be met through the implementation of periodic maintenance measures during the life cycle of the pipelines. The case study involves the calculation of the failure probability due to equipment impact, the calculation of the failure probability due to corrosion, and the estimation the re-inspection interval for domestic natural gas transmission pipelines.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.1
• /
• pp.29-35
• /
• 2010

This paper studies causes of the L-1 blade damage of a low pressure turbine, which was found during the scheduled maintenance, in 500 MW fossil power plants. Many failures of turbine blades are caused by the coupling of aerodynamic forcing with bladed-disk vibration characteristics. In this study the coupled vibration characteristics of the L-1 turbine bladed-disk in a fossil power plant is shown for the purpose of identifying the root cause of the damage and confirming equipment integrity. First, analytic and experimental modal analysis for the bladed-disk at zero rpm as well as a single blade were performed and analyzed in order to verify the finite element model, and then steady stresses, natural frequencies and corresponding mode shapes, dynamic stresses were calculated for the bladed-disk under operation. Centrifugal force and steady steam force were considered in calculation of steady and dynamic stress. The proximity of modes to sources of excitation was assessed by means of an interference diagram to examine resonances. In addition, fatigue analysis was done for the dangerous modes of operation by a local strain approach. It is expected that these dynamic characteristics will be used effectively to identify the root causes of blade failures and to perform prompt maintenance.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.5
• /
• pp.356-360
• /
• 2002

The seedlings of yacon (Polymnia sonchifolia Poeppig ＆ Endlicher), which were cuttings, plug seedling (PS), crown bud before sprouting (CBBS), crown bud after sprouting (CBAS), and divided seedling after budding (DSAB) were planted at 70$\times$50 cm planting distance on ridge; that was interow spacingintrarow spacing, and about 28,500$\pm$71 plants/ha. CBBS didn't need work and equipment to raise seedlings. PS and DSAB grew taller to 140.5 and 143.3cm, respectively, than others at 150 days after planting. In the changes of plant height, PS and DSAB showed taller than others during growth period, cuttings, CBBS, and CBAS grew rapidly in middle growth stage. Excepting main stem and petiole length, other characters were significant for seedling. Fresh weights were different among seedlings. Even though the yield of plants grown from CBAS and CBBS were lower with 34.7 and 36.4 ton/ha, respectively, than 3.6 ton/ha of DSAB; its yield index were over 95%, hence, those of plants grown from cutting and PS were lower with 73 and 87%, respectively. The ratio of tuberous roots over 200g to total tuberous roots per plant was the highest from DSAB. Most of tuberous roots were under 200g per tuberous root from cuttings. CBBS, CBAS, and DSAB are suitable to use seedlings for high yield of yacono. Yacon plant by DSAB much produced tuberous root of over 200g.

• Journal of Broadcast Engineering
• /
• v.25 no.2
• /
• pp.252-264
• /
• 2020

Korea has launched the world-wide first terrestrial UHD broadcast services on May 31, 2017. While the existing HDTV broadcast services use MPEG-2 TS (Tranport Stream) standard for multiplexing and delivering compressed media with additional data, the terrestrial UHD broadcast services use MMT (MPEG Media Transport) standard, which is the next-generation standard beyond MPEG-2 TS. However, the production cost of UHD contents is so high that only a part of the total broadcast time is filled with UHD contents and the UHD time portion is planned to be gradually increased. On the other hand, the ATSC 3.0 standard that uses MMT is not yet used in full-fledged broadcast services in North America. Hence MMT broadcast equipment is still at an early stage with high prices. In this paper we implemented a multi-thread software running on an ordinary PC that can be utilized to realize a low-cost converter that converts the output of an existing MPEG-2 TS multiplexer to an MMTP (MMT Protocol) packet stream. We also verified the functionality of the software through experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.174-178
• /
• 2001

In order to reduce the lead-time and cost, recently the technology of rapid protoyping and manufacturing(RPM)has been widely used. Machining process is still considered as one of the effective RPM methods that have been developed and currently available in the industry. It also offers practical advantages such as precision and versatility. Some considerations are still required during the machining process. One of the most important points is fixturing. There should be an effective method of fixturing since the fixturing time depends on the complexity of geometry of the part to be machined. In this paper, the rapid manufacturing process has been developed combining machining with automatic filling. The proposed fixturing technique using automatic filling can be widely applicable to free surface type of product such as a fan. In the filling stage, remeltable material is chosen for the filling process. An automatic set-up device attachable to the table of the machine has also been developed. The device ensures the quality during a series of machining operations. This proposed process has shown to be a useful method to manufacture the required products with the reduced the response-time and cost.