• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.397-400
• /
• 2001

In this paper, to improve bandwidth of microstrip antenna, we discussed the patch structure using Aperture Stacked Patch. To provid PCS service and IMT-2000 service simultaneous, a microstrip patch antenna needs impedance bandwidth of 22%. But typical microstrip patch antennas have impedance bandwidth of 3∼6%. To analyze characteristics of microstrip pach antenna, we used Ensemble of commercial software. The microsrtip patch antenna was designed and fabricated, tuned. We get following results; 650MHz(33%) of impedance bandwidth for VSWR 1.5. The measured gain of ASP microstrip antenna is 6.94dBi.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.860-867
• /
• 2009

In this paper, we designed the array antenna for FMCW radar in X - band frequency, and we chose stacked structure for improvement of narrow bandwidth. The array antenna is implemented on the circuit board which is relative permittivity 2.33 and the stacked patchs are designed on the circuit board which is relative permittivity 4.6. A Foam which has a similar permittivity of air is added to keep the particular gap between array antenna and the stacked patch. The result of array antenna has characteristics that a half-power beam width is $10.6^{\circ}$ and antenna gain is 18.70 dBi and bandwidth is 1.25GHz at the design frequency of 9GHz. The result of the array antenna with the stacked structure has that the half power beam width is $15.17^{\circ}$ and the antenna gain is 15.85dBi and bandwidth is 2GHz. It is needed to improve the antenna gain as keeping bandwidth in same level.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.11-17
• /
• 2004

In this paper, A miniature broad-band dime antenna is designed. This antenna consists of two stacked circular patches that create two cylindrical slots resonating at two slightly different frequencies, fed by a strategically positioned coaxial prove. To increase the bandwidth of microstrip patch antenna, a configuration of stacked type is used. Furthermore, to reduce the size of microstrip patch antenna and obtain a double resonant behavior, two shorting-walls are used. Experimental results show that the antenna bandwidth is about 26% centered at 5.8㎓ and are close agreement with the calculation results by HFSS 7.0 software.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.437-441
• /
• 2003

The major drawback of the classical microstrip patch antennas Is their narrow band characteristic from 1% to 5%. In this paper, to improve this drawback, we designed the antenna with stacked structure having one drive patch connected with feed line and four identical radiation patches. Resonance is achieved by adjust ing coupling area between one drive patch and four identical radiation patches and changing the size of drive patch or radial ion patches. Used substrate is FR4(${\epsilon}_r$=4.6 and t=1.6mm) and designed center frequency is 2.45GHz. The designed antenna has a wide bandwidth of 380Mhz form 2.333GHz to 2.713GHz(about 15.5%) including ISM band from 2.4GHz to 2.4835GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.618-627
• /
• 1999

In this paper, we have researched designing a microstrip antenna, which will be replaced for a parabolic antenna. A microstrip antenna has been used in extremely limited field, but if it is applied to practical life like a DBS receiving antenna, we expect that it will be used in various way. First of all, if we use a microstrip antenna for a DBS receiving antenna, it should be guaranteed characteristics of broadband frequency. Therefore, the goal of this paper is designing an antenna which guarantees broadband frequency band for a DBS reception. Also, experiment with Koreasat, we have researched the propriety of this antenna for the DBS receiving antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.37-45
• /
• 2000

Though microstrip antenna has several advantages, it makes engineers struggle against the difficulties of narrow bandwidth and scan-blindness with probe-feeding and array configuration. To overcome these disadvantages, stacked patch and cavity-backed structure had been proposed. But this structure can not be analyzed easily because we have no concrete means to analyze it. So the algorithm to analyze the structure should be established to make it useful. This paper explained the algorithm of moment method to analyze the structure and verified it by comparing the calculated and measured results.

• Journal of Advanced Navigation Technology
• /
• v.4 no.1
• /
• pp.23-35
• /
• 2000

In this paper, the design for a PCS base station antenna which is using broadband method by a stacked structure has been studied. The sensitive parameters, such as the parasitic elements, the height of air layer between the upper and lower patch, and the variation of feed point, of the microstrip antenna that has stacked structure in a characteristics variation situation are classified and the characteristics has been investigated through the simulations. A designed antenna has following characters. Impedance bandwidth is Z57.5MHz(VSWR${\leq}$2), horizontal beamwidth is $64.1^{\circ}$, and gain is 14.7dBi. Therefore, it is confirmed the characteristics is good. In this paper, through the designing of a stacked microstrip antenna, we has investigated the availability for Korea PCS base station antenna.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.293-296
• /
• 2002

In this paper, we proposed a beam tilting microstrip patch array antenna for the reception of satellite signals by using low cost copper etched polyester films and foams. The configuration and coupling mechanism of the proposed antenna are similar to the dipole Yagi-Uda antenna. It is composed of 3 layers of polyester films and three layers of foam. In order to prevent unwanted radiation and coupling loss by microstrip feeding networks and parasitic patches, a stacked layer with rectangular slots above the driver patch array is inserted. The 16${\times}$8 element microstrip Patch way antenna is Presented by experimental results. Its beam patterns are affected by many parameters such as sizes of the patches, gap between the patches. characteristics of the substrates, feeding method, etc. Owing to its complexities of various design parameters, both simulation and experiment were performed. The fabricated antenna received DBS signal from KOREASAT 3 by doing nothing but adjusting azimuth direction.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2011

In this paper, dual-feed circularly polarized microstrip patch antenna for GPS L1, GPS L2, GLONASS L1 signal was fabricated by using stacked patch. It was fed by dual coaxial probe on the patch at 50ohm impedance, and was simulated to resonate at GPS L1, GPS L2, GLONASS L1. To realize characteristics of right hand circular polarization using dual-feed stacked patch antenna and hybrid coupler for $90^{\circ}$ phase difference. Output of hybrid coupler was contacted input of Low Noise Amplifier(LNA). The LNA using dual band pass filter was designed and fabricated. The measured results of the implemented antenna is VSWR < 1.5 : 1 and the gain of 32dB(Zenith) over at GPS L1, L2, GLONASS L1.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.5
• /
• pp.874-879
• /
• 2016

A wideband stacked patch antenna with parasitic elements, rectangular and triangle shaped patches, is proposed. Two different shaped parasitic elements are placed in the above of main rectangular microstrip patch antenna in order to achieve wide bandwidth for 860 MHz band. Coupling between the main patch and parasitic patches is realized by thick air gap. The gap and locations of parasitic patches are found to be the main factor of the wideband impedance matching. The proposed antenna is designed and fabricated on a ground plane with small size of $119mm{\times}109mm$ for application of compact transceivers. The fabricated antenna on an FR4 substrate shows that the minimum measured return loss is below -11.68dB at 824 MHz and an impedance band of 818~919 MHz(11.7%) at 10dB return loss level. The measured radiation patterns are similar to those of a conventional patch antenna with maximum gain of 2.11 dBi at 824 MHz.