• 지구물리와물리탐사
• /
• 제19권1호
• /
• pp.11-19
• /
• 2016

나머지 정적보정 기법중에서 가장 많이 쓰이는 주행시간 분해기법과 겹쌓기제곱 최대화기법의 적용성을 육상 탄성파자료에서 비교 검토하였다. 모든 발파점과 수신점에 대한 임의의 나머지 정적보정값(시간차이)과 무작위 잡음이 포함된 모델자료에서 겹쌓기제곱 최대화기법은 주행시간 분해기법에 비해 흐트러진 반사 이벤트를 정확히 정렬시키고 보정과정에서 출력된 발파점과 수신점의 정적보정 그래프가 입력된 값과 거의 같은 진폭으로 역전된다는 점에서 신호대잡음이 작은 자료의 반사면 향상에 보다 효과적이었다. 나머지 정적보정에 적합한 입력인자(최대허용 시간차이, 상관창, 반복횟수)들은 공통중간점 자료외에 공통발파점 겹쌓기자료와 공통수신점 겹쌓기자료에 대한 연속 테스트를 거쳐 효과적으로 진단할 수 있었다. 나머지 정적보정에 앞서 송수신점의 높이보정 및 풍화대 깊이보정을 실시하여 장파장 시간차이를 제거하고 진동수-파수 필터링, 예측곱풀기, 시간변화 빛띠흰색화로 잡음을 줄여 교차상관의 오차를 최소화시킨다. 또한 나머지 정적보정후 수직시간차 역보정을 거쳐 속도를 재분석하여 겹쌓기한 결과 저류층을 포함한 반사면들의 향상된 연속성 및 분해능을 확인할 수 있었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권2호
• /
• pp.34-38
• /
• 2013

AC Losses for face to face stacks of four identical coated conductors (CCs) were numerically calculated using the H-formulation combined with the E-J power law and the Kim model. The motive sample was the face to face stack of four 2 mm-wide CC tapes with 2 ${\mu}m$ thick superconducting layer of which the critical current density, $J_c$, was $2.16{\times}10^6A/cm^2$ on IBAD-MgO template, which was suggested for the mitigation of ac loss as a round shaped wire by Korea Electrotechnology Research Institute. For the calculation the cross section of the stack was simply modeled as vertically aligned 4 rectangles of superconducting (SC) layers with $E=E_o(J(x,y,t)/J_c(B))^n$ in x-y plane where $E_o$ was $10^{-6}$ V/cm, $J_c$(B) was the field dependence of current density and n was 21. The field dependence of the critical current of the sample measured in four-probe method was employed for $J_c$(B) in the equation. The model was implemented in the finite element method program by commercial software. The ac loss properties for the stacks were compared with those of single 4 cm-wide SC layers with the same critical current density or the same critical current. The constraint for the simulation was imposed in two different ways that the total current of the stack obtained by integrating J(x,y,t) over the cross sections was the same as that of the applied transport current: one is that one fourth of the external current was enforced to flow through each SC. In this case, the ac loss values for the stacks were lower than those of single wide SC layer. This mitigation of the loss is attributed to the reduction of the normal component of the magnetic field near the SC layers due to the strong expulsion of the magnetic field by the enforced transport current. On the contrary, for the other case of no such enforcement, the ac loss values were greater than those of single 4cm-wide SC layer and. In this case, the phase difference of the current flowing through the inner and the outer SC layers of the stack was observed as the transport current was increased, which was a cause of the abrupt increase of ac loss for higher transport current.

• 한국인터넷방송통신학회논문지
• /
• 제22권5호
• /
• pp.29-35
• /
• 2022

본 논문에서는 신재생에너지 산업생태계의 한 영역을 담당하는 연료전지 산업에서 요구되는 인력을 양성함에 있어서, 기업의 교육비 부담 감축과 교육 효과 향상을 위하여 메타버스에 탑재한 연료전지 교육 프레임워크를 제안하였다. 본 Meta-Fuel cell 플랫폼은 Unity 3D 웹을 활용하여 1인칭 시점의 플랫폼을 구성하여 이론교육과 실습교육을 진행할 수 있도록 구성하였다. 이 플랫폼은 ppt 발표, 동영상 실행 등등 다양한 단위 교육 콘텐츠를 수용할 수 있도록 설계하였고 프로토타입을 구현하였다. 현재, 본 플랫폼에는 이론교육을 위한 ppt 및 동영상 시연 외에 실습을 위한 소프트웨어 콘텐츠 "STACK-Up"이 통합되어 있다. 이론교육 부문은 신재생에너지, 수소경제, 연료전지 등의 수소에 관한 교양지식 서비스를 제공한다. 소프트웨어 "STACK-Up"은 건물용 연료전지 핵심부품인 스택의 분해-조립 공정을 실습할 수 있는 서비스를 제공한다. Meta-Fuelcell 플랫폼은 교육자에게는 대면 교육의 한계점을 개선하여 교육 장소, 시간, 인원 등의 제약이 없는 비대면 교육의 기회를 제공하고, 학습자에게는 교육 주제, 순서 등을 선택권을 부여하며 메타버스 공간에서 학습할 수 있는 흥미로운 경험을 제공한다. 본 플랫폼은 연료전지 인력양성 사업에 실험적으로 적용하며 개선을 진행하고 있다.

• Journal of Electrical Engineering and Technology
• /
• 제8권3호
• /
• pp.565-571
• /
• 2013

This paper presents an effective method to improve efficiency of switched reluctance motor by optimizing energy conversion loop. A nonlinear analytical model which takes saturation account is developed to calculate inductance and flux-linkage. The flux-linkage curve is studied to calculate the co-energy increment to obtain the optimum exciting current. For a given cross-section, the exciting current at which co-energy increment is maximum was found to be constant while stack length varies. Then the energy conversion loop was optimized by varying the stack length and turns of windings. The constraints during optimization were that motor was excited by the maximum increment co-energy current and the energy in the loop was determined by rated power of motor. Dynamic finite element analysis was used to evaluate the efficiency of various models and the comparison of results shows promising effects of the proposed method. Experiment was also conducted to validate the simulation result.

• 지구물리와물리탐사
• /
• 제11권4호
• /
• pp.279-285
• /
• 2008

한반도 남해 제주도 남동부해역 도미분지에 대하여 한국지질자원연구원은 2007년 2차원 해양탄성파 탐사를 수행하였다. 탐사의 목적은 한반도 해역의 대륙붕에서 기반암의 구조를 파악하고 대륙붕 내의 자원부존 가능성을 분석하고자 함이다. 기반암의 구조를 파악하기 위해서는 중합단면 및 구조보정 단면을 효율적으로 구성하는 것이 필요하다. 그러나 탐사해역의 수심은 평균 100 m 내외로 해수면과 해저면 사이에서 발생하는 다중반사파가 일부 구간에서 강하게 기록되어 기초전산처리 기법만으로는 중합단면에서 기반암의 구조가 명확히 분석되지 않는 경우가 있다. 본 연구에서는 도미분지 2차원 탄성파 자료에 대한 최적의 전산처리 변수를 도출하고자 하였고 특히 페그레그 해저면 다중반사파(peg-leg multiple)를 제거하는데 주 목적을 두었다. 탄성파 자료 전산처리의 주요 단계는 최소위상 예측 디콘볼루션(minimum phase predictive deconvolution), 속도분석 및 레이던 필터(Radon filter)로 구성되었으며 각 단계마다 중합단면을 계산하여 적용한 전산처리 변수가 적절히 설정되었는지를 검증하였다. 자료처리 결과 본 연구에서 설정한 변수들이 도미분지 탄성파 자료 전산처리에 효과적임을 확인하였다.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.545-550
• /
• 2013

Piezoelectric PMN-29PT single crystal multilayer actuators [100 $mm^2$ in cross section and 22 mm in length] are designed and fabricated by stacking square plates [$10{\times}10{\times}0.5(t)\;mm^3$] of PMN-29PT single crystals having a $d_{33}$ of about 1,500 pC/N. The characteristics of PMN-29PT multilayer actuators are compared with those of P-025.40P multilayer PZT ceramic actuators [490 $mm^2$ in cross section and 60 mm in length] produced by PI in Germany. Even though the total volume of the PMN-29PT single crystal multilayer actuator is only about 7.5% of that of the P-025.40P ceramic multilayer actuator, PMN-29PT single crystal multilayer actuators are expected to show very similar properties to P-025.40P ceramic actuators in terms of static stroke and blocking force. Therefore, on the basis of their smaller mass and volume compared to the conventional PZT ceramic multilayer actuators, piezoelectric PMN-29PT single crystal multilayer actuators have significant potential regarding the development of various high performance actuators for aerospace subsystems.

• 한국광학회지
• /
• 제19권2호
• /
• pp.122-126
• /
• 2008

본 논문에서는 단일 광원에 광분할 반사경을 집적하여 휴대폰의 디스플레이부와 키패드부에 동시 적용 가능한 통합형 듀얼 백라이트 유닛을 제안하고 구현하였다. 이 광분할 반사경은 상부 커버와 홈 모양의 하부 기판을 서로 정렬함으로써 구현되며, 반사경 좌우에는 도광판, 확산 쉬트, 프리즘 쉬트로 이루어진 도광 모듈이 연결되어 있다. 하부 기판의 중앙에 위치한 광원에서 방사된 광은 반사경 내부에서 다중 반사를 하면서 진행하고, 도광 모듈에 입사된 후 면광원으로 변환된다. 제작된 듀얼 백라이트 유닛의 측정 결과를 살펴보면, 키패드부에서의 평균 휘도 및 휘도 균일도는 각각 $420\;cd/m^2$와 69%, 디스플레이부에서는 $640\;cd/m^2$와 79%였다.

• 한국태양에너지학회 논문집
• /
• 제32권3호
• /
• pp.1-10
• /
• 2012

The purpose of this study was to promote the utilization of wind velocity of kitchen and bathroom exhaust ducts for wind power generation in high-rise apartments. The research content can be summarized as follows: 1) Nine high-rise apartments were examined for the installation of kitchen and bathroom exhaust ducts located in the pipe shaft (PS) section. After selecting simulation candidates, a simulation was performed with the STAR-CCM+ Ver 5.06 program. 2) Of nine high-rise apartments, seven had kitchen and bathroom exhaust ducts, whose cross section was in the range of $0.16m^2{\sim}0.4m^2$. The area ratio between the exhaust ducts and PS section (cross section of exhaust duct/area of PS section ${\times}$ 100) was on average 3.2%. 3) The simulation results were analyzed. As a result, the smaller cross section kitchen and bathroom exhaust ducts had, the more advantages there were for increasing exhaust wind velocity. If an out air inlet duct is installed to the old kitchen and bathroom exhaust ducts, it will increase exhaust wind velocity by 3.01~3.98m/s and contribute to the proper wind velocity level (3.0m/s). 4) When the simultaneous usage rate between the kitchen and bathroom exhaust fan increased from 20% to 60%, exhaust wind velocity increased. The "entire house holds" condition for exhaust fan operation provided more even exhaust wind velocity than the "some house holds" condition. 5) Exhaust wind velocity increased in the order of amplified (T-3), induced (T-2) and vertical (T-1) top of kitchen and bathroom exhaust ducts. Of them, the amplified type (T-3) was under the least influence of external wind velocity and thus the most proper for kitchen and bathroom exhaust duct tops.

• 한국수소및신에너지학회논문집
• /
• 제18권4호
• /
• pp.458-463
• /
• 2007

An experimental study on scale-up of Electro-electrodialysis(EED) to increase the efficiency of HI decomposition section in the IS(Iodine-Sulfur) process was carried out. The EED stack extends the effective area of the membrane to 20 times of that formerly used in a single EED unit cell. The experiment was carried out using HIx solution($HI:H_2O:I_2=1:8.4{\sim}9:1.85{\sim}1.9$) at $100^{\circ}C$ and various solution flow rates of 20, 30, 40 and 50 cc/min. The increased HI molality in catholyte after one-pass throughout from the EED stack was 3 mol/kg-$H_2O$, 2.2 mol/kg-$H_2O$, 2 mol/kg-$H_2O$ and 1.37 mol/kg-$H_2O$ at 20, 30, 40 and 50 cc/min, respectively. These values satisfied the target of HI molality(the increase of HI molality: 2 mol/kg-$H_2O$) in the IS process for hydrogen production of 20 L/hr.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.87.2-87.2
• /
• 2011

Many type of fuel cell stacks have been developed to improve the efficiency of reactants usage. The cascade type fuel cell stack using dead end operation is able to attain above 99% usage of hydrogen and oxygen. It is sectionalized to several parts and the residual reactants which are used previous parts would be supplied again to next parts which have less number of cells in dead end operation stack. The oversupply of reactants which is usually 120%~150% of the theoretical amount to generate current for preventing the flooding effect could be provided to each part except the last one. The final section which is called monitoring cells is supposed to be supplied insufficient the fuel or oxidant that would have some accumulated inert gas from former parts. It makes some voltage drop in the part and the fresh reactants must be supplied to the part for recovering it by venting the residual gas. So the usage of fuel and oxidant is depend on the time and frequency of opening valves for venting of residual gas and it is important to optimize the vent logic for achieving higher usage of hydrogen and oxygen. In this research, many experiments are performed to find optimal condition by evaluating the effect of time and frequency under several power conditions using over 100kW class fuel cell module. And the characteristics of the monitoring cells are studied to know the proper cell voltage which decide the condition of opening the vent valve for stable performance of the cascade type fuel cell module.