• Steel and Composite Structures
• /
• 제47권6호
• /
• pp.709-728
• /
• 2023

Experimental and analytical studies were conducted to clarify the influencing mechanisms of the longitudinal reinforcement on performance of axially loaded Reinforced Concrete-Filled Steel Tube (R-CFST) short columns. The longitudinal reinforcement ratio was set as parameter, and 10 R-CFST specimens with five different ratios and three Concrete-Filled Steel Tube (CFST) specimens for comparison were prepared and tested. Based on the test results, the failure modes, load transfer responses, peak load, stiffness, yield to strength ratio, ductility, fracture toughness, composite efficiency and stress state of steel tube were theoretically analyzed. To further examine, analytical investigations were then performed, material model for concrete core was proposed and verified against the test, and thereafter 36 model specimens with four different wall-thickness of steel tube, coupling with nine reinforcement ratios, were simulated. Finally, considering the experimental and analytical results, the prediction equations for ultimate load bearing capacity of R-CFSTs were modified from the equations of CFSTs given in codes, and a new equation which embeds the effect of reinforcement was proposed, and equations were validated against experimental data. The results indicate that longitudinal reinforcement significantly impacts the behavior of R-CFST as steel tube does; the proposed analytical model is effective and reasonable; proper ratios of longitudinal reinforcement enable the R-CFSTs obtain better balance between the performance and the construction cost, and the range for the proper ratios is recommended between 1.0% and 3.0%, regardless of wall-thickness of steel tube; the proposed equation is recommended for more accurate and stable prediction of the strength of R-CFSTs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.42-42
• /
• 2008

Considerable attention has been focused on the applications of flexible liquid crystal (LC)-based displays because of their many potential advantages, such as portability, durability, light weight, thin packaging, flexibility, and low power consumption. To develop flexible LCDs that are capable of delivering high-quality moving images, like conventional glass-substrate LCDs, the LC device structure must have a stable alignment layer of LC molecules, concurrently support uniform cell gaps, and tightly bind two flexible substrates under external tension. However, stable LC molecular alignment has not been achieved because of the layerless LC alignment, and consequently high-quality images cannot be guaranteed. To solve these critical problems, we have proposed a PDMS pixel-wall based bonding method via the IB irradiation was developed for fasten the two substrates together strongly and maintain uniform cell gaps. The effect of the IB irradiation on PDMS with PI surface was also evaluated by side structure configuration and a result of x-ray photoelectron spectroscopic analysis of PDMS interlayer as a function of binder with substrates. large number of PDMS pixel-walls are tightly fastened to the surface of each flexible substrate and could maintain a constant cell gap between the LC molecules without using any other epoxy or polymer. To enhance the electro-optical performance of the LC device, we applied an alignment method that creates pretilt angle on the PI surface via ion beam irradiation. Using this approach, our flexible LCDs have a contrast ratio of 132:1 and a response time of about 15 ms, resulting in highly reliable electro-optical performance in the bent state, comparable to that of glass-substrate LCDs.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1066-1071
• /
• 2005

This paper presents the two lossless auxiliary inductors-assisted voltage source type half bridge (single ended push pull: SEPP) series resonant high frequency inverter for induction heated fixing roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation for wide its output power regulation ranges and load variations under its constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operating principle is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation characteristics-based on the high frequency PDM strategy. The experimental operating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimental ones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliance implemented here is proved from the practical point of view.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 학술대회 논문집
• /
• pp.415-420
• /
• 2005

This paper presents the two lossless auxiliary inductors-assisted voltage source type half bridge (single ended push pull: SEPP) series resonant high frequency inverter for induction heated king roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation for wide its output power regulation ranges and load variations under its constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operating principle is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation characteristics-based on the high frequency PDM strategy. The experimental operating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimental ones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliance implemented here is proved from the practical point of view.

• 한국결정성장학회지
• /
• 제23권5호
• /
• pp.255-264
• /
• 2013

$CoAl_2O_4$는 열적 및 화학적으로 매우 안정한 물질이며 독특한 광학적 특성으로 인해 도자기 제품, 유리, 페인트, 플라스틱을 장식하는 세라믹 착색제로 사용되어져 왔다. 본 연구에서는 착체중합법(Polymerized complex method)과 고상합성법(Solid state reaction)을 이용하여 단상의 $CoAl_2O_4$ 청색 무기 안료를 합성하였고, 잉크젯 프린팅용 잉크로의 응용 시 노즐 막힘 및 분산안정성과 같은 문제점을 방지하기 위해 고에너지 밀링 공정 중 하나인 어트리션밀을 이용하여 입자를 미세화하였다. 밀링 공정은 직경 1 mm의 지르코니아 볼을 이용하여 BPR(Ball to powder weight ratio) 100 : 1, 800 rpm의 조건에서 3시간 동안 진행되었다. 합성된 안료는 XRD, FE-SEM, TEM, PSA, 그리고 CIE $L^*a^*b^*$ 측정을 통하여 어트리션밀링 전후의 특성을 분석하였다. XRD 측정 결과 단상의 $CoAl_2O_4$ 청색 무기 안료가 합성되었고, 고에너지 밀링 공정을 통하여 100~200 nm의 입자 크기를 가지는 청색 나노 무기 안료를 얻었다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제20권7호
• /
• pp.121-134
• /
• 2015

Spatial and temporal changes in algal population in Yongdam reservoir and ecological factors that induced the changes in the size and composition of algal population were investigated by monthly sampling at ten locations in the reservoir. Nutritional state of the reservoir was identified to be phosphorus-limited with nitrogen to phosphorus (N : P) ratio much greater than 17 in most samples. Algal population was dominated by three taxonomic groups, diatoms, chlorophytes and cyanobacteria. Although explosive algal growth was not observed in the summer, algal population showed transition with time of the dominant algal type from diatoms in the winter to cyanobacteria in the summer. Chlorophyta was not the dominant group in the reservoir although they maintained relatively stable number of cells in the reservoir and showed increase in population from March to May. The application of statistical methods revealed that the factors inducing changes in cell number of each group were water temperature for diatoms and cyanobacteria and phosphorus concentration for chlorophyte. Fluctuation of cyanobacterial population was mainly observed near the inlet of tributaries while diatoms showed higher variation inside the reservoir.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.86-89
• /
• 2002

We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 10[mN/m]. In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/Poly-${\gamma}$ Benzyl $_D$-Glutamate/Al and Au/Poly-${\gamma}$ Benzyl $_D$-Glutamate/Au; the number of accumulated layers is 1, 3, 5 and 7. Also, we then examined of the MIM device by means of I-V. The I-V characteristic of the device is measured from 0 to +2[V]. We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system. LB film accumulated by monolayer on an ITO. In the cyclicvoltammetry, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode measured in $LiBF_4$ solution, stable up to 0.9V vs. Ag/AgCl.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권1호
• /
• pp.102-108
• /
• 2006

On the refutation demanded for a control of various toxic substances. PCBs(poly chlorinated biphenyl) has a fatal poisonous matter in the ecosystem and the environmental pollution as it Is a kind of stable chemical substance. Especially, the gross Product of PCBs is estimated at about one million tonnage all over the world. However it is kept on storing in untreated state, then has a deterioration by the Prolonged storage and a risk of overflowing. Therefore, this research examined the fundamental characteristics of combustion and emission for the target of using the IPA (iso-propyl alcohol) solution as a part of PCBs control. IPA was filled to three kinds of Vessel, i.e. Vessel I, II, and III, and then was investigated as follows combustion shape, flame temperature. mass burning velocity, and PM(Particulate matter). A radial thermometer and a C-A thermocouple measured the flame temperature, and the optical extinction method by using He-Ne laser and the filter weight method used in the PM measurement. As a result, with an increasing of L/S ratio, the flame length become shorter and the burning velocity is more rapid, but the particulate matters is higher. It is supposed that the air flow rate is high on Vessel. and then the combustion is Promoted in the surface area of the upstream zone. The future works plan to investigate the characteristics with an using of the mixing of IPA and PCBs

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.723-726
• /
• 2002

We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 10[mN/m]. In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/Poly-$\gamma$ Benzyl $_D$-Glutamate/Al; the number of accumulated layers is 1, 3, 5 and 7. Also, we then examined of the MIM device by means of I-V. The I-V characteristic of the device is measured from 0 to +2[V]. We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system. LB film accumulated by monolayer on an ITO. In the cyclicvoltammetry, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode measured in $LiBF_4$ solution, stable up to 0.9V vs. Ag/AgCl.

• 동아시아경상학회지
• /
• 제6권2호
• /
• pp.28-48
• /
• 2018

Purpose - This study is to analyze the assessment of forming of a payment balance of the country and its condition. Data array were used the data on the Russian Federation from the 1995-2016, across Great Britain - since the 2004- 2014 and in the retrospective aspect since the 1946. Research design, data, and methodology - The payment balance is a ratio of payment amounts made this country abroad and the receipts received by it from abroad for a certain period; it is the systematic list of all economic transactions performed for a certain period of time between the residents of one country and the nonresidents. The scale of research on Russia: to be analyzed the amount of data from the 1995 by 2016. On Great Britain - the 2004-2014, on South Korea - the 2017. Results - Hypothesis 1. The detailed and simple systematization of balance sheet items increases the efficiency of analytical procedures and the mechanism of public administration. Hypothesis 2. The main of balance sheet items are deficit of Russian Federation scarce which, are generally counterbalanced with gold and foreign exchange reserves. Conclusions - Considering the items of balance of payments of the studied countries in the context with other countries, it can be noted that the dynamics of the main items are closely linked with the main macroeconomic indicators and reflects the main tendency of the state development. The main items of balance sheet of South Korea's are intensive. The relatively stable dynamics in the macroeconomic indicators is observed in Japan and China