• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.1
• /
• pp.9-17
• /
• 2014

Purpose: The purpose of this study was to compare zirconia implants with titanium implants from the view point of biomechanical stability and histologic response on osseointegration when those were placed with xenograft materials. Materials and methods: Specimens were divided into two groups; the control group was experimented with eighteen titanium implants which had anodized surface and the experimental group was experimented with eighteen sandblasted zirconia (Y-TZP) implants. At the tibias of six pigs, implants were installed into bone defect sites prepared surgically and treated with resorbable membranes and bovine bone. Two pigs were sacrificed after 1, 4 and 12 weeks respectively. Each implant site was sampled and processed for histologic and histomorphometric analysis. The stability of implants was evaluated with a $Periotest^{(R)}$. And the interfaces between bone and the implant were observed with a scanning electron microscope. Results: In stability analysis there was no significant difference between Periotest values of the control group and the experimental group. In histologic analysis with a light microscope after 4 weeks, there was new bone formation with the resorption of bovine bone and the active synthesis of osteoblasts in both groups. In bone-implant contact percentage there was significant difference between both groups (P<.05). In bone area percentage there was no significant difference between both groups. In analysis of both groups with a scanning electron microscope there was a gap between bone and a surface at 4 weeks and it was filled up with bone formed newly at 12 weeks. Conclusion: When accompanied by xenograft using membrane, bone to implant contact percentage of zirconia implants used in this experiment was significantly less than that of the titanium implants by surface treatment of anodic oxidation. So, it is considered that the improvement of zirconia implant is needed through ongoing research on surface treatment methods for its practical use.

• Korean Journal of Food Science and Technology
• /
• v.50 no.3
• /
• pp.267-273
• /
• 2018

Horse fat was extracted from fatty horse meat at $70^{\circ}C$ under vacuum conditions. The oxidative stability of horse fat was investigated by the addition of 0, 30, 60, and 150 mg/kg of ${\alpha}$-, ${\gamma}$-, or ${\delta}$-tocopherol during storage of 14 days at $65^{\circ}C$ in the dark. Changes of tocopherol concentration and fatty acid composition, peroxide value, and 2-thiobarbituric acid (TBA) value were analyzed during storage. The levels of the added tocopherols were found to decrease during storage. Unsaturated fatty acids contents of horse fat without tocopherol decreased from 60.87% to 57.22% after 14 days. The peroxide value and TBA value increased as storage time increased. The peroxide values of horse fat after addition of 0, 30, 60, and 150 mg/kg of ${\gamma}$-tocopherol were 43.75, 25.17, 20.87, and 15.41 meq/kg, respectively, and the TBA values were 7.87, 5.64, 4.43, and 4.23 mg malonaldehyde (MA)/kg, respectively, after 14 days. At the concentration of 150 mg/kg, both ${\gamma}$- and ${\delta}$-tocopherol impeded the oxidation of horse fat during storage.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.2
• /
• pp.243-248
• /
• 1998

Ark shell was known as shellfish that had hemoglobin as blood pigment and the action of mecidine, was consumed the great part of it as raw material, though it was produced about 13,000 M/T per year. Ark shell was processed the infinitesimal quantity as conned product, bout canned ark shell had problem that occurrenced discoloration after heat treatment during processing and storage. This discoloration mechanism during processing and storage was not cleared. This study was carried out to understand characteristics of the hemoglobin as blood pigment and carotenoid as meat pigment in ark shell and management of proper processing conditions for prevention of oxidation and discoloration by thermal treatment. When treated by digestion of 0.1% BHA, 0.1% Tenox-II, 0.5% Na2EDTA, 0.05% NDGA and 3% salt soln., 0.1% BHA solution was most suitable for stability of carotenoid that the retention ratio of carotenoids were 63.1% after heating to 116$^{\circ}C$ for 120 minutes. In preparation of canned ark shell and storage at 37$\pm$1$^{\circ}C$ for 60 days, the chemical composition, pH and salinity ere stable. And contents of total carotenoid were decreased slightly from 0.83mg% to 0.727mg%. The viable cell count were 6.92$\times$103 cfu/ml at raw ark shell, after processed and storage were not detected. The predominant amino acids in the raw ark shell were glutamic acid(19.7%), arginine(16.0%), glycine(12.6%), alanine(12.2%) and aspartic acid(7.6%). When 60 days stored, the contents of amino acid were stable. And the predominant nuclotide and their related compounds in the raw ark shell were hypoxanthine(2.14$\mu$mol/g), IMP(1.94$\mu$mol/g) and ATP(0.87$\mu$mol/g), and storage at 37$\pm$1$^{\circ}C$ for 60 days, the quantity order were same as raw material.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.1
• /
• pp.4-31
• /
• 2018

The Neolithic pottery excavated from the Jungsandong site has been classified into four types of pottery (I: feldspar type, II: mica type, III: talc type and IV: asbestos type) according to their mineral composition. These four types of potteries generally appear to have undergone incomplete firing, while the level of oxidation in the type I pottery objects, which have a relatively higher clay content, was found to be particularly low. The type III objects, which have a high talc content, are judged to have been somewhat slow in removing carbon because they contain saponite belonging to the smectite group. Of the four types of pottery, type IV showed the highest redness and the most uniform characteristics, thus indicating a good level of oxidation. In particular, fixed carbide (C; 33.7 wt.%) with a thickness of about 1mm, and originating from organic substances, was detected inside the walls of the type I pottery, while the deep radial cracks in the outer surfaces of the pottery are thought to have been caused by repeated thermal shocks. Given that all of the pottery except for the type I artifacts are considered to be have been made for storage purposes, those containing talc and tremolite are easy to done liquid storing vessels based on an analysis of their material characteristics. As for the type II relics, which are composed of various minerals and exhibit poor physical properties, they seem to have been used for simple storage purposes. As domestic talc and asbestos mines were concentrated in the areas of Gyeonggi, Gangwon, Chungbuk, and Chungnam, it seems likely that talc and tremolite were produced as contiguous minerals. Considering the distance between the remains in Jungsandong and these mines and their geographical distribution, there is a possibility - albeit somewhat slight - that these mines were developed for the mining of various minerals. Although ultramafic rock masses - such as serpentine capable of generating talc and tremolite - have not been found in the Jungsandong area, limestone and biotite granite containing mica schist have been identified in the northwestern part of Yeongjong Island, indicating that small rock masses might have formed there in the past. Therefore, it is judged necessary to accumulate data on pottery containing talc and tremolite, other than the remains in Jungsandong, and to investigate the rocks and soils in the surrounding area with greater precision. The firing temperatures of the pottery found at the Jungsandong site were interpreted by analyzing the stability ranges of the mineral composition of each type. As a result, they have been estimated to range from 550 to $800^{\circ}C$ for the type I artifacts, and from 550 to $700^{\circ}C$ for the type I, II and IV artifacts. However, these temperatures are not the only factors to have affected their physical properties and firing temperature, and the types, particle sizes, and firing time of the clay should all be taken into consideration.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1158-1164
• /
• 1998

Aluminium sulfate solution was prepared by sulfuric acid treatment from gibbsite. Aluminium sulfate hydrate [$Al_2(SO_4)_3$ · $nH_2O$] was precipitated from aluminium sulfate solution by adding it into ethylalcohol. From XRD analysis as-prepared $Al_2(SO_4)_3$ · $nH_2O$ was confirmed to have mixed-crystalization water(n=18, 16, 12, 6). The average water of crystalization calculated from thermogravimetry(TG) was 14.7. Aluminium sulfate hydrate [$Al_2(SO_4)_3$ · $nH_2O$] was thermally decomposed and converted to $Al_2(SO_4)_3$ at $800^{\circ}C$, $\gamma-Al_2O_3$ at $900-1000^{\circ}C$, and $\alpha-Al_2O_3$ at $1200^{\circ}C$. Ni-doped $\gamma-Al_2O_3$, was synthesized from the slurry of as-prepared $\gamma-Al_2O_3$, with the ratio of [Ni]/[Al]=0.5. The reaction conditions of synthesis were determined as initial pH 9.0 and temperature $80^{\circ}C$ The basicity(pH) of slurry was controlled by using urea and $NH_4OH$ solution. Urea was also used for deposition-precipitation. For determining termination of reaction, the data acquisition was performed by oxidation reduction potential(ORP), conductivity and pH value in the process of reaction. Termination of the reaction was decided by observing the reaction steps and rapid decrease in conductivity. On the other hand, BET(Brunauer, Emmett and Teller) and thermal diffusity of Ni- doped $\gamma-Al_2O_3$, with various content of Ni were measured and compared. Thermal stability of Ni- doped $\gamma-Al_2O_3$ at $1250^{\circ}C$ was confirmed from BET and XRD analysis. The surface state of Ni-doped $\gamma-Al_2O_3$ was investigated by X-ray photoelectron spectroscopy(XPS). The binding energy at $Ni2P_{3/2}$ increased with increasing the formation of $NiAl_2O_4$ phase.

• Korean Journal of Food Science and Technology
• /
• v.28 no.5
• /
• pp.928-934
• /
• 1996

Rice bran, treated with heat or ${\gamma}-radiation$, was stored at $-15^{\circ}C,\;4^{\circ}C,\;37^{\circ}C$ and room temperature to determine its lipid stability by monitoring the changes in moisture, free fatty acids (FFA) and peroxide value (POV). Initial moisture content of rice bran was 14% and decreased with time. The higher storage temperature, the more moisture loss. The moisture content became 9% after 80 days of storage at $37^{\circ}C$. The initial FFA of rice bran was 2.5% which increased with time except the samples stored at $-15^{\circ}C$. The higher storage temperature, the more FFA was produced, by 9 times the initial FAA after 80 days of storage at $37^{\circ}C$. POV increased about twice the initial value after 80 days of storage at $-15^{\circ}C,\;4^{\circ}C$, and room temperature, and 5 times at $37^{\circ}C$. Rice bran was treated with heat at $70^{\circ}C,\;90^{\circ}C\;or\;105^{\circ}C$ and stored for 2 weeks at $30^{\circ}C$: The higher the heat treatment temperature and the longer the heat treatment time, the more moisture was lost. The not show any significant changes. Irradiation at $1{\sim}30\;kGy$ and subsequent storage for 4 weeks at $5^{\circ}C\;or\;30^{\circ}C$ caused negligible changes in moisture content. The FFA contents of rice bran irradiated up to 10 kGy were almost similar to these of nonirradiated one when measured just after irradiation. The samples irradiated at 30 kGy were 1.5 times higher in the FFA contents than nonirradiated ones. But there was little influence of irradiation doses on the FFA contents during storage. Irradiation caused the increase in POV of rice bran. resulting in 4 times increase in case of 30 kGy irradiated sample. During the storage, however, the POV of irradiated rice bran decreased significantly.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.609-614
• /
• 2013

This study investigated the spontaneous combustion behavior of solvent-treated low rank coals. Indonesian lignite (a KBB and SM coal) and sub-bituminous (a Roto coal) were mixed with non-polar 1-methyl naphthalene (1MN) either by mechanical agitation or ultrasonication. The property change associated with 1MN treatment was then analyzed using proximate analysis, calorific value analysis, Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy and moisture re-adsorption test. Susceptibility to spontaneous combustion was evaluated using crossingpoint temperature (CPT) measurement along with gas analysis by GC. A FT-IR profile showed that oxygen functional groups and C-H bonding became weaker when treated by 1 MN. XPS results also indicated a decrease of the oxygen groups (C-O-, C=O and COO-). Increased hydrophobicity was found in the 1MN treated coals during moisture readsorption test. A CPT of the treated coals was ${\sim}20^{\circ}C$ higher than that of the corresponding raw coals and the ultrasonication was more effective way to enhance the stability against spontaneous combustion than the agitation. In the gas analysis less CO and $CO_2$ were emitted from 1MN treated coals, also indicating inhibition of pyrophoric behavior. The surface functional groups participating in the oxidation reaction seemed to be removed by the ultrasonication more effectively than by the simple mechanical agitation.

• Food Science of Animal Resources
• /
• v.30 no.3
• /
• pp.472-478
• /
• 2010

The effects of rosemary and $\alpha$-tocopherol, added individually or in combination, on broiler performance, thiobarbituric acid reactive substance (TBARS), total plate count (TPC) and meat color of chicken thigh meat were investigated. Three hundred broiler chicks divided into five groups were fed a basal diet (control) or basal diet supplemented with 5 g rosemary/kg (T1), 10 g rosemary/kg (T2), 200 mg $\alpha$-tocopherol/kg (T3), or 5 g rosemary/kg + 200 mg $\alpha$-tocopherol/kg (T4) for 5 weeks. Following slaughter, chicken meat was stored at $4^{\circ}C$ for 10 days. All treatments did not influence the performance. Rosemary supplementation delayed lipid oxidation in thigh meat during refrigerated storage. T2 was significantly (p<0.05) more effective in delayed lipid oxidation compared to T1, but was inferior to T3. Samples containing a combination of antioxidant had lower TBARS values than those containing the individual antioxidants, indicating a synergistic effect. TPC was significantly increased (p<0.05) in thigh meat of all groups throughout the refrigerated storage. The T3 and control groups showed TPC counts that did not differ from each other during the entire storage period. However, rosemary supplementation was associated with bacterial counts that were significantly lower (p<0.05) than the control and $\alpha$-tocopherol groups at day 3 of storage and thereafter. For this period, T1 presented TPC counts that were significantly higher than the T2 group (p<0.05). At all storage times, the thigh meat of rosemary-fed chickens was redder than control (higher $a^*$), while no differences in $L^*$ and $b^*$ values were found. A synergistic effect was obtained from the combination of rosemary with $\alpha$-tocopherol, whereas individual use of the antioxidants significantly improved color stability compared to the control.

• Food Science of Animal Resources
• /
• v.37 no.2
• /
• pp.219-227
• /
• 2017

The objective of this study was to determine the physicochemical and sensory properties of cooked emulsion sausages containing different levels of lotus rhizome powder (0, 1, 2, and 3%, based on total weight). Lotus rhizome powder had no significant (p>0.05) impact on pH, moisture, protein, or ash content of sausage. However, fat content was slightly but significantly (p<0.05) decreased when the level of lotus rhizome powder was increased in the sausages. The addition of lotus rhizome powder to sausages at over 1% resulted in significantly (p<0.05) darker and less red color of cooked sausage compared to control. Increase in lotus rhizome level slightly improved the emulsion stability and apparent viscosity. Significant (p<0.05) reduction in cooking loss was observed when more than 1% of lotus rhizome powder was added to sausages. The textural properties of sausages were unaffected by the inclusion of lotus rhizome except for springiness and chewiness. On the manufacture day, control sausage had significantly (p<0.05) higher TBARS value than treatments. Regarding sensory characteristics, increased levels of lotus rhizome powder decreased (p<0.05) color and juiciness scores. However, cooked sausages exhibited similar overall acceptability regardless of the level of lotus rhizome powder added to sausages. Therefore, lotus rhizome powder, an antioxidant dietary fiber, could be used as an effective natural ingredient in meat products for the development of healthier and functional food.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.5
• /
• pp.352-357
• /
• 2009

Due to rapid consumption of hydrogen peroxide, large amount of hydrogen peroxide is required when Fenton reaction is applied to the contaminated soil. In this study, acetate was employed as a ligand of $Fe^{2+}$ to enhance the efficiency of removal of phenanthrene by securing the stability of hydrogen peroxide. 0.5 ${\sim}$ 3 times of acetate (2${\sim}$12mM) was added to compare with molar concentration of $Fe^{2+}$. Low initial concentration of hydrogen peroxide was 0.7% to eliminate side effect of removal efficiency. The results showed that hydrogen peroxide lifetime was lasted up to 72 hours, or more than 50 times of normal lifetime. Phenanthrene removal efficiency was improved up to 70% due to stabilized hydrogen peroxide. Ferrous ion was oxidized to ferric ion and oxidation-reduction was repeated during the reaction. Finally ferric ion was reduced to ferrous by $HO_2$. It was confirmed that, due to the influence of hydrogen peroxide, pH was acid region and it remained at the range of 4 ${\sim}$ 5 when 8 mM or more of acetate was added. Acetate which was used as the ligand of Fe was also decomposed by Fenton reaction. The decomposition time of acetate was slower than phenanthrene. Therefore, it was able to come to the conclusion that phenanthrene was superior to acetate at the competition for decomposition. Through the results of this study, it was able to identify the possibilities to improve the efficiency of Fenton reaction in the contaminated soil and its economic feasibility, and to move to more realistic technique through research expanded to neutral pH region.