• 한국주조공학회지
• /
• 제23권1호
• /
• pp.30-39
• /
• 2003

Porous hybrid preforms were fabricated by reactive sintering using the compacts consisting of SiC particles, Fe and Al powders. Squeeze casting processing was employed to produce the composite in which the matrix phase is Al-Si7Mg. The microstructural change and wear resistance of the composites were investigated in terms of an amount of SiC particles. The wear loss was increased with increasing the contact pressure in the alloy containing SiC particles coated with Cu. The most drastic change was found to the specimen tested at 2.5 MPa of contact pressure. Concerning the alloys containing SiC particles coated with Ni-P, a drastic increase in the wear loss exhibited at 2 MPa of contact pressure in those alloys containing 4 and 8 wt. % of SiC particles coated with Ni-P. In the alloy containing 16 wt. % a proportional increase in wear loss was observed to the change of contact pressure. With respecting to the sliding velocity, the wear loss of the alloy containing SiC particles coated with Cu increased at the initial stage of wear process and then decreased. Similar result was found in the alloys containing SiC particles coated with Ni-P. On the basis of the present results obtained, it was found that wear resistance of the alloys tested was improved to show in the order of the alloy reinforced by coated SiC particles > by uncoated SiC particles > by intermetallic compound without SiC particles.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.581-593
• /
• 1990

본 연구에서는 교반기술에 의하여 얻어진 반응고상태의 금속에 단섬유를 첨가 하여 복합재료를 제조하였다. 그리고 제조되어진 복합재료에 있어서 섬유의 분산상 태및 기지재와의 접합관계를 조사하여 압연가공에 필요한 반응고상태인 금속복합재료 의 제조방법을 확립하였다. 균일하게 분실되어진 반용융상태의 단섬유강화형 금속복 합재료를 직접 압연하여 박판을 제조할 수 있는 가능성을 검토하였으며, 또한 제조되 어진 박판의 인장시험에 의하여 기계적 성질을 조사하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.373-378
• /
• 2002

Metal matrix composites have a great interest in recent years because high specific strength, high specific stiffness characteristics, and application ranges of the composites are extend to variety industry. In this paper, an investigation was performed on the plane strain fracture toughness and slinding wear properties of AC4CH alloy(Al-Si-Mg line) reinforced with 20wt% aluminum borate whisker expect one, which contained a inorganic binder($TiO_2$). the binder led to the formation of strengthen the whisker each other. The test of fracture toughness was using CT(half size) specimen of thickness 12.5mm, width 25mm. and test of slinding wear of using tribo a pin-on-disk machine and lubricant is used without paraffine 8.2CST at room temperature. As results, Fracture toughness $K_{IC}$ is $8.7MPa-m^{05}$ for ABOw/AC4CH, $9.28MPa-m^{05}$ for ABOw/AC4CH added $TiO_2$. but AC4CH alloy was violated the critical stipulated by ASTM standard for valid measurement of $K_{IC}$. In case of, it was performed $J_{IC}$ test instead of $K_{IC}$ based on ASTM E 1820.

• 비파괴검사학회지
• /
• 제16권4호
• /
• pp.225-233
• /
• 1997

초음파법을 이용한 금속 복합재료의 비파괴 평가 방법을 확립하기 위하여 용탕단조법으로서 SiC/AC8A 합금계 금속 복합재료를 제조하였다. 이때 입자의 크기가 기계적 특성과 초음파 특성에 미치는 영향을 검토하기 위하여 강화 입자의 크기를 4.86, 8.09, $11.44{\mu}m$로 서로 다른 세 종류로 달리하였으며, 또한 강화입자 함유량이 초음파 특성에 미치는 영향을 검토하기 위하여 각 강화 입자의 크기에 대하여 강화 입자 함유율을 14, 22.5, 27.5, 35%의 네 종류로 시료를 준비하였다. 이와 같은 시료에 대하여 기계적 성질중에서 가장 기본이 되는 탄성계수에 대하여 초음파 음속법을 이용하여 그 유효성 및 측정 정도에 대하여 검토를 하였으며 초음파 음속, 감쇠 특성을 이용한 금속 복합재료의 미세조직 평가 방법에 대하여서도 검토하였다. 그 결과, 초음파 음속법에 의한 탄성계수 측정은 기계적 시험에 의한 변형률 측정법과 같은 측정 정도를 나타낼 수 있을 정도로 유효할 뿐만 아니라 초음파 음속, 감쇠 특성을 이용하면 금속 복합재료의 조직 인자중 특히 강화 섬유의 크기 및 함유율을 비파괴적으로 정도 높게 평가할 수 있다는 것을 알았다.

• 한국주조공학회지
• /
• 제22권1호
• /
• pp.42-48
• /
• 2002

Effects of coating treatment of metallic Cu, Ni-P film on $SiC_p$, for $SiC_p$/iron aluminide composites were studied. Porous hybrid preforms were fabricated by reactive sintering after mixing the coated $SiC_p$, Fe and Al powders. Then the final composites were manufactured by squeeze casting after pouring AC4C Al alloy melts in preforms. The change of reactive temperature, density, microstructure of the preforms and microstructure of the composites were investigated. The exprimental results were summarized as follows. The thickness of Cu and Ni-P metallic layer formed on $SiC_p$ by electroless plating method were about $0.5{\mu}m$ and coated uniformly. There was no remakable change in the ignition temperature with variation of the mixing ratio of Fe and Al powder while in the case of coated $SiC_p$ it was lower about $20^{\circ}C$ than in the non-coated $SiC_p$. The maximum reaction temperature increased with increasing Al contents, but decreased with increasing $SiC_p$ contents. Expansion ratio of preform after reactive sintering increased with amount of Cu coated $SiC_p$. In the case of Fe-70at.%Al, the expansion ratio was about 7% up to 8wt.% of $SiC_p$, addition but further addition of $SiC_p$, increased the ratio significantly. And in the case of Fe-50 and 60at.%Al, it was about 20% up to 16wt.% of $SiC_p$ addition and about 28% in 24wt.% of $SiC_p$, addition. The microstructures of compounds showed that the grains became finer as amount of $SiC_p$, and mixing ratio of iron powder increased and the shape of compounds was changed gradually from irregular to spheroidal.

• 한국주조공학회지
• /
• 제11권6호
• /
• pp.475-481
• /
• 1991

In this study the fabrication technology and mechanical properties of AC8A/$Al_2O_3$ Composites by squeeze casting process were investigated to develope for application as the piston materials that require good friction, wear resistance, and thermal stability. AC8A/$Al_2O_3$ composistes without a porosity and the break of preform were fabricated at the melt temperature of $740^{\circ}C$, the preform temperature of $500^{\circ}C$, and mold temperature of $400^{\circ}C$ under the applied pressure of $1200kg/cm^2$ as the results of the observation of microstructures. As the results of this study, the tensile strength of AC8A/$Al_2O_3$ composites was not increased linearly with $Al_2O_3$ volume fraction and so it seemed not to agree with the rule of mixture, which had been used often in metal matrix composite. Also the tensile strength after thermal fatigue test was little different from that before the test. Consequently it was thought that AC8A/$Al_2O_3$ composites fabricated under our experimental conditions had a good thermal stability and subsequently a good interface bonding. Wear rate(i.e., volume loss per unit sliding distance) of AC8A/$Al_2O_3$ composites was decreased with $Al_2O_3$ volume fraction and the sliding speed at both room temperature and $250^{\circ}C$ and so there was a good correlation between wear rate and hardness. Also the wear rate of AC/8A20% $Al_2O_3$ composities was obtained the value of $1.65cm^3/cm$ at sliding speed of 1.14m/sec as compared with about $3.0\;{\times}10^{-8}cm^3/cm$ hyereutectie Al-Si alloy(Al-16%Si-2%Cu-1%Fe-1%Ni), which applied presently for piston materials. The wear behavior of $Al_2O_3$ composites was observed to a type of abrasive wear by the SEM view of wear surface.

• Composites Research
• /
• 제16권1호
• /
• pp.1-12
• /
• 2003

본 연구는 보강재의 부피분율이 49%, 56%, 63%첨가된 패키징용 SiC/Al복합재료를 가압주조법을 통해 개발하였다. SiC/Al복합재료는 0.8%의 무기성형제와 $Al_2$O$_3$섬유가 SiC입자에 비해 부피비 1:10의 비율로 첨가되었으며 새로이 고안된 몰드에서 제조되었다. 제조된 SiC/Al복합재료에 대해 30-300 구간에서 열팽창 계수를 측정하고, FEM수치해석과 비교하여 온도에 따른 특성을 분석하였다. 실험결과 SiC/Al복한재료의 열팽창계수는 혼합법칙, Turner모델의 중간값을 가졌으며 상온에서는 Turner모델에 가깝다가 온도가 높아질수록 혼합법칙에 가까와졌다. 이러한 특성은 모재의 소성변형 및 잔류응력에 의한 것으로 본 연구에서 제안한 모재와 보강재 사이에 작용하는 평균응력 차이로부터 분석이 된다. 해석결파 모재의 소성변형이 시작되는 온도에서 SiC/Al복합재료의 열팽창계수가 급격히 증가하였으며, 가공 잔류응력은 이러한 소성변형의 시작온도를 고온으로 이동시킴으로써 열팽창계수에 영향을 끼침을 밝혔다. 이러한 일련의 연구를 통해 온도에 따른 열팽창 특성은 복수입자모델에 의한 2차인 해석을 통해 성공적으로 분석됨을 보였다.

• 한국재료학회지
• /
• 제9권3호
• /
• pp.315-321
• /
• 1999

금속기지 복합물은 구조용 재료로서 매우 우수한 성질을 지니고 있어 광범위하게 연구되어져 왔다. $Al_2O_3$와 SiC는 그들의 우수한 기계적 특성 때문에 일반적인 보강재로서 사용되어져 왔다. 그러나 이들 세라믹 보강재는 비싼 재조 비용 때문에 특별한 목적을 위해서만 한정되어 사용되어져 왔다. 본 연구에서는 우리는 Al 합금기지 복합물에서 SHS법에 의해 합성된 $Al_2O_3$-SiC 분말의 보강재로서의 응용 가능성을 살펴보았다. 또한 $Al_2O_3$단섬유를 Al기지 하이브리드 복합물에 적용하기 위하여 합성된 분말과 함께 첨가하였다. 25vol% 강화재의 복합물을 제조하기 위하여 용탕단조법을 사용하였다. 미세구조와 결정구조는 SEM, OM 그리고 XRD로 관찰하였고 압축시험과 마모시험으로 기계적인 성질들을 조사하였다.