• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.311-314
• /
• 2004

The housing of the fuel injector supports the rod, the niddle valve and the solenoid. Based on the procedure of process design, in this paper, the forming operation is designed by the rigid-plastic finite element method. The metal flow during the forming of the fuel injector housing is axisymmetric until the final forming process. The response surface method has been performed to reduce the under-fill and the maximum effective strain. From the results of RSM, the second order regression model of equation is calculated by the least square method and used to determine the optimal values of design variables by simultaneously considering the responses. It is noted that upper under-fill is affected by the design variables of the $2^{nd}$ forming process and lower under-fill is affected by the design variables of the 1st forming process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.415-418
• /
• 2008

We propose a criterion which predicts wrinkle initiation on workpiece in groove rolling process based on finite element analysis. Fundamental idea introduced in the criterion is to examine the difference between flat rolling which don't' cause wrinkling at all and groove rolling which usually accompanies it. The proposed criterion assumes that irregular distribution of shear strain on workpiece during groove rolling is attributable to the initiation of wrinkling. The proposed criterion has been applied to roughing train in the rod and bar mill of SEAH BESTEEL Inc. A new design for 2nd pass (square roll groove) was suggested, machined and applied. Results reveal that the proposed criterion in this study could point out the location of wrinkle initiation during groove rolling and could reduce onset of wrinkle on final products.

• Structural Engineering and Mechanics
• /
• 제13권2호
• /
• pp.171-186
• /
• 2002

Static and dynamic penetration tests of reinforced concrete (RC) slab specimens are described and discussed. The experimental study was aimed at a better understanding of mechanisms that are involved in dynamic penetration, through their identification in static tests, and by establishing their relative influence in similar dynamic cases. The RC specimens were $80{\times}80-cm$ square plates, and they were made of 30 MPa concrete. The non-deforming steel penetrator was a 50-mm diameter steel rod with a conical nose of 1.5 aspect ratio. Impact penetration tests were carried out with an air gun, which launched the projectiles at velocities of up to 300 m/sec. The static tests were conducted using a closed loop displacement control actuator, where the penetrator was pushed at a constant rate of displacement into the specimen. The static tests reveal important mechanisms that govern the penetration process and therefore contribute to a better understanding of RC barriers resistance to non-deforming projectiles impact.

• Current Optics and Photonics
• /
• 제3권3호
• /
• pp.243-247
• /
• 2019

We have developed a compact, wavelength-selectable, Q-switched Nd:YAG laser at mid ultraviolet for chemical warfare agent detection. The fundamental wave at 1064 nm is delivered by a pulsed solid state laser incorporating with a square-type Nd:YAG rod in a resonator closed by two crossed Porro prisms for environmental reliability. The output energy at 213 nm ($5{\omega}$) and 266 nm ($4{\omega}$) by ${\chi}^{(2)}$ process in the sequentially disposed BBO crystals are measured to be 6.8 mJ and 15.1 mJ, respectively. The output wavelength is selected for $5{\omega}$ and $4{\omega}$ by a motorized wavelength switch. The energy ratio of the $5{\omega}$ to the $4{\omega}$ is varied from 0.05 to 0.85 by controlling the phase matching temperature of the nonlinear crystal for sum-frequency generation without change of the output pulse parameters.

• 한국결정성장학회지
• /
• 제10권5호
• /
• pp.345-349
• /
• 2000

Micro-pulling down법을 이용하여 $Al_2O_3/ZrO_2$eutectic fiber를 제조하여 그 미세구조 및 기계적 특성과 성장속도의 관계를 조사하였다. 성장속도는 0.1~15 mm/min였으며, 직경 0.2~2 mm, 길이 500 mm의 eutectic fiber를 제조하였다. $Al_2O_3/ZrO_2$eutectic fiber의 미세구조는 성장속도에 따라 rod-shape structure에서 lameller structure를 거쳐 lamellar pattern을 갖는 cellular structure로 변화하였다. lamellar thickness는 성장속도가 1 mm/min에서 15 mm/min로 증가함에 따라 380 nm에서 110 nm로 감소하였다. 이와 같은 성장속도에 따른 lamellar thickness의 감소경향은 inverse-square-root로 나타내면, = 1 -l/2와 같이 표현할 수 있다. 여기서 는 m, 는 m/s의 단위를 갖는다. 13.1 Gpa의 hardness, 900 Mpa의 상온인장강도를 나타냈으며, 성장속도의 증가 즉, interlamellar spacing이 감소함에 따라 증가하는 경향을 나타냈다.

• 한국정보통신학회논문지
• /
• 제5권1호
• /
• pp.133-143
• /
• 2001

본 논문은 직각파 및 뇌충격진류에 대한 봉상접지각의 과도임피던스 특성을 정상접지지항과 비교.분석하였다. 접지계는 단일$(\Psi10[mm], 1[m])$과 5[m]의 간격을 두고 서로 연접한 3연접 봉상접지극으로 구성하였으며, 과도 임피던스 특성을 분석하기 위하여 상승시간 30[ns], 펄스폭 $20[\mus]$의 직각파전류 발생장치를 설계 제작하였다. 실제 낙뢰에 의한 접지임피던스의 변화를 관찰하기 위하여, 국제규격 ANSI/IEEE, IEC에 규정되어 있는 뇌충격전류를 인가하여 이에 따른 특성변화를 측정.분석하였다. 접지계로 유입된 과도전류는 접지계의 전위를 상승시키며, 이 때의 전위상승과 유입전류의 비로써 접지임피던스를 산출하며, 뇌격전류에 대한 경제적인 보호 수준을 평가.예측하기 위하여 임피던스 파라미터를 측정결과로부터 산출하였다. 또한 연접에 따른 접지임피던스의 감소와 접지리드선이 미치는 영향도 분석하였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.33-38
• /
• 1997

Criticality experiments with fixed neutron poison plates for water moderated and reflected low enriched(2.35 and 4.31 wt%) UO$_2$fuel rod clusters were evaluated to validate calculation techniques employed in analyzing fuel shipping and storage systems having steel, boral, or cadmium shield. Measurements were obtained for both the 2.35 wt% and the 4.31 wt% enriched rods in square pitched, water flooded lattices. The critical experiments with the 2.35 wt% enriched rods consists of three 20$\chi$ 16 or 20$\chi$ 17 fuel cluster. Critical separation were used in the experiments with the 4.31 wt% enriched fuel rods. In the experiments, the poison plates were placed on both sides of the centrally located fuel cluster. Critical separation between the three sub-critical fuel clusters were then measured for varying plate thicknesses and distances of the plates to the center fuel cluster. Calculations were performed for thirty eight critical configuration using KENO-V. a and MCNP. All of the results were within 1.23% in $\Delta$k when individually compared with the critical value of 1.0. Discrepancies of the code results are probably due to uncertainties in experiments and/or analytical modeling experiments. In general, MCNP predictions were observed to be in best agreement with the experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.133-136
• /
• 1999

Many researches on the identification of a system have been carried out using a least square method, an adaptive filter, and so on. However, it is difficult to apply these methods in a nonlinear system. In the case of a nonlinear system, it is known that the signal compression method is able to estimate uncertain parameters of linear element in a nonlinear system because it is able to separate linear element and nonlinear element in a nonlinear system. However, the signal compression method cannot be applied to a motion simulator because actuators of the simulator is single-rod cylinders which includes expansion and compression dynamic properties. Therefore, this paper proposes a modified signal compression method which is able to estimate uncertain parameters of the motion simulator dynamics. The dynamic properties of this system are identified by separating expansion and compression properties when applying the signal compression method. And then, the identified parameters are applied to design a sliding mode controller for the simulator. The performance of the designed sliding mode controller is evaluated experimentally.

• Earthquakes and Structures
• /
• 제19권5호
• /
• pp.315-329
• /
• 2020

Through bolt connections in Concrete Filled Steel Tubes (CFSTs) has been proved to be good in terms of seismic performance and constructability. Stiffened extended end plate connection with full through type bolt helps to avoid field weld altogether, and hence to improve the quality of joints. An experimental study was conducted on the hysteretic performance of square interior beam-column connections using flat extended end plates with through bolt. The study focuses on the effect of the bond between the tie rod and the core concrete on the cyclic performance of the joint. The study also quantifies how much the interior joint is getting strengthened due to the confinement effect induced by bi-directional bolting, which is widely used in 3D moment resisting frames. For a better understanding of the mechanism and for the prediction of shear capacity of the panel zone, a mathematical model was generated. The various parameters included in the model are the influence of axial load, amount of prestress induced by bolt tightening, anchorage, and the concrete strut action. The study investigates the strength, stiffness, ductility, and energy dissipation characteristics. The results indicate that the seismic resistance is at par with American Institute of Steel Construction (AISC) seismic recommendations. The bidirectional bolting and bond effect have got remarkable influence on the performance of joints.

• Advanced Composite Materials
• /
• 제17권4호
• /
• pp.359-372
• /
• 2008

The moisture absorption behavior of carbon fiber-reinforced plastic (CFRP) and its effect on dimensional stability were examined. Moisture diffusivity in CFRP was determined by measuring a specimen's weight during the moisture absorption test. Three types of CFRP specimens were prepared: a unidirectionally reinforced laminate, a quasi-isotropic laminate and woven fabric. Each CFRP was processed into two geometries - a thin plate for determination of diffusivity and a rod with a square cross-section for the discussion of two-dimensional diffusion behavior. By solving Fick's law expanded to 3 dimensions, the diffusivities in the three orthogonal directions were obtained and analyzed in terms of the anisotropy of CFRP moisture diffusion. Coefficients of moisture expansion (CMEs) were also obtained from specimen deformation caused by moisture absorption. During moisture absorption, the specimen surfaces showed larger deformation near the edges due to the distribution of moisture contents. This deformation was reasonably predicted by the finite element analysis using experimentally determined diffusivities and CMEs. For unidirectional CFRP, the effect of the fiber alignment on CME was analyzed by micromechanical finite element analysis (FEA) and discussed.