• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.760-763
• /
• 2007

The properties of carbon nanotube obtained by thermal chemical vapor deposition (CVD) process were investigated as a function of ammonia $(NH_3)$ gas in hydrocarbon gas, Fe catalyst thickness, and growth temperature. Fe catalyst was prepared by DC magnetron sputter and pre-treated with ammonia gas. CNTs were then grown with ammonia-acetylene gas mixture by thermal CVD. The diameter of these CNTs shows a strong correlation with the gas rate, the catalyst film thickness and temperature. From our results, it was found that the factors of grown CNTs positively acted to improve CNT quality.

• Journal of the Korean Ceramic Society
• /
• v.37 no.11
• /
• pp.1025-1032
• /
• 2000

산화분위기에서의 반응성 이온빔 스퍼터링법으로 Sn과 Sb 금속 타겟을 사용하여 실온에서 ATO 박막을 증착하였다. Sb 첨가량, 박막의 두께 및 열처리가 ATO 박막의 전기적 특성과 광학적 특성에 미치는 효과를 연구하고자 하였다. 제조된 ATO 박막의 두께는 약 1500$\AA$과 1000$\AA$으로 조절하였으며, Sb 농도는 10.8wt% 또는 14.9wt%임이 XPS 분석에 의하여 확인되었다. 증착한 박막의 열처리는 40$0^{\circ}C$~$600^{\circ}C$의 온도범위에서 산소 또는 forming gas(10% H$_2$-90% Ar) 분위기에서 30분간 수행하였다. 이렇게 제조된 ATO 박막은 Sb의 첨가량, 두께 및 열처리 조건에 따라 다양한 전기 비저항 값과 가시광선 대역에서의 광투과도를 나타내었다.

• Journal of Surface Science and Engineering
• /
• v.37 no.1
• /
• pp.1-4
• /
• 2004

MoS$_2$-Ti films were deposited on SKD-11 tool steel substrate by a D.C. magnetron sputtering system. The influence of deposition parameters on the adhesion of the films was investigated by the scratch test. Crosssection morphology was evaluated using FE-SEM. The plasma etching played an important role on the adhesion of the films. The appropriate etching conditions roughened the surface, resulting In the improved adhesion of the film. The adhesion of the film increased with the interlayer thickness up to 110 nm and then decreased slightly with further increasing of interlayer thickness. The adhesion was highest at a bias voltage of -50 V. Further increase of the bias voltage decreased the film adhesion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.901-904
• /
• 2000

In order to investigate the effect of deposition conditions on crystallographic properties of ZnO thin films by Facing Targets Sputtering system which can deposit thin films in plasma-free situation and change the deposition conditions in wide range. The characteristics of zinc oxide thin films on power, inter targets distance, and substrate temperature were investigated by XRD(x-ray diffractometer), alpha-step (Tencor) analyses. The excellently c-axis oriented zinc oxide thin films were obtained at sputter pressure 1mTorr, sputtering current 0.4A, substrate temperature 300$^{\circ}C$, inter target distance 100mm. In these conditions, the rocking curve of zinc oxide thin films deposited on Glass was 3.9$^{\circ}$.

• Journal of Surface Science and Engineering
• /
• v.29 no.3
• /
• pp.157-162
• /
• 1996

The effects of microstructural change on the adhesion strength between Cu/Cr film and polyimide have been studied. Cr films (50 nm thick) and Cu films (500 or 1000 nm thick) were deposited on polyimide by DC magnetron sputtering. During Cu deposition the Ar pressure was 5 or 100 mtorr. The microstructure was observed by SEM and the adhesion was measured by T-peel test. Plastic deformation of peeled metal strips was characterized quantitatively by using XRD technique. The film in which Cu is deposited at 100 mtorr has higher adhesion strength than the film in which Cu is deposited at 5 mtorr. And in the film with same deposition pressure of 100 mtorr, the adhesion strength is increased as the deposited thickness increases from 500 to 1000 nm. The adhesion change of Cu/Cr can be interpreted as the difference in plastic deformation.

• Journal of Surface Science and Engineering
• /
• v.33 no.4
• /
• pp.266-272
• /
• 2000

Sputtered $MoS_2$ thin films provide lubrication and wear improvements for vacuum and space applications. In this study, deposition of $MoS_2$ thin films by R.F. magnetron sputtering was studied with regard to the micro-structural change of $MoS_2$ film and mechanical properties. The coating parameters such as the working pressure, the RF power, the substrate temperature, the etching time were varied to determine how these parameters affected the film morphology and mechanical properties of deposited films. The best wear properties and critical load were observed with the film deposited at $70^{\circ}C$, 1.0$\times$$10^{ -3}$ Torr, 170W and 1 hour deposition time. The critical load increased with the increase of sputter etching time.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.655-658
• /
• 1995

Magnetization behavior of sputter-deposited Co/Pd multilayers were characterized, and it has been found that even when the multilayers are sputtered at low pressure (10 mTorr), the coercivity of the multilayers can be increased to large extent without noticeable change of saturation magnetization by increasing the deposition pressure of Pd underlayer. It turned out that the surface topology of Pd underlayer gets rough as deposition pressure increases, which consequently affects the magnetization reversal mode of Co/Pd multilayers from domain wall motion to magnetic spin rotation. The enhancement of coercivity is attributed to the domain wall pinning effect which is comected with the surface roughness of Pd underlayer on which Co/Pd multilayers grow.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.960-964
• /
• 2004

[ $Ba_2NaNb_5O_{15}$ ](BNN) thin films have been prepared by the ion beam sputter deposition (IBSD) method on Pt coated Si substrate at temperature as low as $600^{\circ}C$ XRD, SEM were used to investigate the crystallization and microstructure of the films. It was found that the films were crack-free and uniform in microstructure. The electric properties of thin films were carried out by observation of D-E hysteresis loop, dielectric constant and leakage current. It was found the deposition rate strongly influenced the phase formation of the films, where the phase of $BaNb_2O_6$ was always formed when the deposition rate was high. However, the single phase (tungsten bronze structure ) BNN thin film was obtained with the deposition rate as low as $22{\AA}/min$. The remanent polarization Pr and dielectric constant are about 1-2 ${\mu}C/cm^2$ and $100\sim200$, respectively. It was also founded the electric properties of thin films were influenced by the deposition rate. The Pr and dielectric constant of films increased with the decrease of deposition rate. The effects of annealing temperature and annealing time to the crystallization behavior of films were studied. The crystallization of thin film started at about $600^{\circ}C$. The adequate crystallization was gotten at the temperature of $650^{\circ}C$ when the annealing time is 0.5 hour or at the temperature of $600^{\circ}C$ when the annealing time is long as 6 hours.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.22-28
• /
• 2012

Transparent dye-sensitized solar cells have been widely investigated for the application to building integrated photovoltaic system. Thin film Si-based solar cells are emerging as a substitute for the dye-sensitized solar cells because their merits of well-established manufacturing processes. Since the selective transmitting layer transmits visible light and reflects infrared light, the solar cell efficiency increases with the introduction of the selective transmitting layer. In this work, AlTiO thin films were grown as the selective transmitting layer by cost-effective sputter deposition and their transmittances were improved by controlling deposition parameters.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.249-249
• /
• 2015

Silver films have been of considerable interest for years due to their better performance relative to other metal films for engineering applications. A series of multi-layer silver coatings with different thickness (i.e. 0.3 um to 1.5 um) were prepared on Aluminium substrate containing copper undercoat by direct current (DC) magnetron sputtering method. For the comparative purpose, similar thickness silver coatings were prepared by electrolytic deposition method. Microstructural, morphological, and mechanical characteristics of the silver coatings were evaluated by means of scanning electron microscope (SEM), X-ray diffraction (XRD), Surface roughness test, microhardness test and nano-scratch test. From the results, it has been elucidated that the silver films prepared by DC magnetron sputtering method has superior properties in comparison to the wet coating method. On the other hand, DC magnetron sputtering method is relatively easier, faster, eco-friendly and more productive than the electrolytic deposition method that uses several kinds of hazardous chemicals for bath formulation. Therefore, a New Work Item Proposal (NWIP) for the test methods standardization of DC magnetron sputtered silver coatings has recently been proposed via KATS, Korea and a NP ballot is being progressed within a technical committee "ISO/TC107-metallic and other inorganic coating".