• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.135-138
• /
• 2004

Since the upsetting type is superior to an extrusion type to get the dimensional accuracy of cold forged spur gear, the upsetting type process far spur gear cold forging has been studied. FE analysis of upsetting type process fur spur gear cold forging was performed to investigate about flow pattern of workpiece and die stress. To analyze the elastic characteristics of die, both rigid and elastic material model were used during loading stage. Under-filled defects were detected In lower portions of spur gear forged by upsetting type in experimental. When the elastic material model for die was used, the under-filled defects could be predicted. On the other hand, if the material model of die was rigid, the defects could not been presented because the die deflection was not considered.

• Clinics in Shoulder and Elbow
• /
• 제22권3호
• /
• pp.139-145
• /
• 2019

Background: The present study was undertaken to evaluate the relationship between location of the rotator cuff tear and shape of the subacromial spur. Methods: Totally, 80 consecutive patients who underwent arthroscopic repair for partial thickness rotator cuff tear were enrolled for the study. Bigliani's type of the acromion, type of subacromial spur, and location of partial thickness tear of the rotator cuff were evaluated using plain X-ray and magnetic resonance imaging. We then compared the groups of no spur with spur, and heel with traction spur. Results: Of the 80 cases, 25 cases comprised the no spur group, and 55 cases comprised the spur group. There was a significant difference in type of tear (p=0.0004) between these two groups. Bursal side tears were significantly greater (odds ratio=6.000, p=0.0007) in the spur group. Subjects belonging to the spur group were further divided into heel (38 cases) and traction spur (17 cases). Comparing these two groups revealed significant differences only in the type of tear (p=0.0001). Furthermore, the heel spur had significantly greater bursal side tear (odds ratio=29.521, p=0.0005) as compared to traction spur. Conclusions: The heel spur is more associated to bursal side tear than the traction spur, whereas the traction spur associates greater to the articular side tear.

• 한국정밀공학회지
• /
• 제14권12호
• /
• pp.105-113
• /
• 1997

In this study, the forging process of spur gears has been investigated. The forging process of spur gears has been classified into two type of operations, guiding one and clamping one in this investigation. Two type forgings of spur gears have been analysed by using upper bound method. The predicted values of the forging load were compared with those obtained from the forging experiments. The forging experiments were carried out with a commercial aluminium alloy. The forged parts obtained through the guiding type forging were campared with those obtained through the clamping type forging.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1015-1019
• /
• 1997

In this study, the forging process of spur gears has been investigated. The forging peocess of spur gears has been classified into two type of operations, guiding one and clamping one in this investigation. Two type forgings of spur gears have been analysed by using upper bound method. The predicted values of the forging load were compared with those obtained from the forging experiments. The forging experiments were carried out with a commerial aluminium alloy. The forged parts obtained through the guiding type forging were campared with those obtained through the clamping type forging.

• 한국전자파학회논문지
• /
• 제15권12호
• /
• pp.1178-1183
• /
• 2004

본 논문에서는 정사각형 패치 안테나에 핀 다이오드(PIN diode)를 사용하여 편파변환 특성을 갖는 새로운 형태의 안테나를 제안하였다. 제안된 안테나는 정사각형 패치면 위에 한 쌍의 스퍼라인(spur-line)과 스퍼라인 위에 핀 다이오드를 삽입한 구조이다. 스퍼라인은 핀 다이오드의 on/off특성에 의해 I형 슬롯라인(slot-line)과 L형 스퍼라인의 형태로 변환되어 편파 변환 특성을 나타내었다. 안테나의 측정 결과 선형편파로 동작할 때에는 -15 dB 이상의 낮은 교차 편파 특성을 나타내었고, 원형편파로 동작할 때에는 0.83 dB의 좋은 축비 특성을 나타내었다. 안테나의 -10 dB대역폭은 on/off상태에 따라 각각 $2.1\%$와 $4.1\%$의 특성을 나타내었다. 또한, 원형편파로 동작하는 안테나의 축비 대역폭은 $3.5\%$의 비교적 넓은 대역폭의 특성을 나타내었다. 따라서 제안된 안테나는 동일한 대역폭 안에서 편파 변환 특성을 나타낼 수 있기 때문에 단일 안테나를 이용하여 주파수를 재사용하는 시스템에서 사용할 수 있다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.242-247
• /
• 1998

The conventional closed-die forging processes had been applied to forging of the spur gears. But this type process requires high pressure. The commercial finite element analysis code ANSYS for the stress and elastic deformation of non-axisymmetric die was adopted in this study. In the non-axisymmetric die such as gear forging, maximum stresses were imposed on the tip of the gear tooth. When the stress exceeds yield strength of insert die, many approaches were attemped to prevent the die failure. Good shaped products are forged successfully. This type process could by used as an advanced technique to replace conventional hobbing process of gear.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제9권3호
• /
• pp.153-159
• /
• 2009

A CMOS frequency synthesizer for $5{\sim}6$ GHz UNII-band sub-harmonic direct-conversion receiver has been developed. For quadrature down-conversion with sub-harmonic mixing, octa-phase local oscillator (LO) signals are generated by an integer-N type phase-locked loop (PLL) frequency synthesizer. The complex timing issue of feedback divider of the PLL with large division ratio is solved by using multimodulus prescaler. Phase noise of the local oscillator signal is improved by employing the ring-type LC-tank oscillator and switching its tail current source. Implemented in a $0.18{\mu}m$ CMOS technology, the phase noise of the LO signal is lower than -80 dBc/Hz and -113 dBc/Hz at 100 kHz and 1MHz offset, respect-tively. The measured reference spur is lower than -70 dBc and the power consumption is 40 m W from a 1.8 V supply voltage.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.307-311
• /
• 1993

Research concerning gears included in rotating machines has been reported using the acoustic emission (AE) method, however, almost no research has been conducted using the AE method in regard to running gears in a bending fatigue processor spur gear teeth. Therefore, in this report, a power circulating-type gear testing machine was used and AE signals and crack length were measured in the bending fatigue process of case-hardened spur gear. Furthermore, the envelope of the AE signal was detected and various analysis were carried out in this data. In the course of the experiments, the following results were observed : the AE signal envelope consists mainly of contact frequency component and twice as many as this;two peaks of AE appear in each tooth contact by the tip corner contact ; as a result of the severe tip corner contact ; as a result of the severe tip corner contact with the sudden increase of crack length, AE signal becomes large.

• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.67-74
• /
• 1991

The contact characteristics of gear tooth surface were studied by using the gear test rig of power circulation type. The effect of surface treatment conditions and revolutions on the tooth surface roughness parameters, and the relations between the lubrication conditions and tooth surface conditions, in spur gear sets wear considered. The result show that heat treatment of gear have an important effect upon fatigue strength and tooth surface conditions, and surface asperities undergo a circulating process of creation and destruction because of the influnce of plastic deformation. And surface roughness conditions at the tooth tips accompany a great deal of variation in running-in stage. According to the lubrication analysis and the study the tooth surface have a greater effect on surface demage than lubrication conditions, in mixed-lubrication condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.142-145
• /
• 1995

It is important from prevention of the malfunction and an important accident by the failuer, to detect a failuer in revolution devices. The acoustic emission(AE) method is expected as means that defects an abnormal phenomenon of revolution devices earlily and utilized. Although a research example by the AE method is reported regarding a gears, little reserch has been conducted using the AE method for running gears in a bending fatigue process of spur gear teeth. Therefore, in this report, with two micro AE sensors attached to the side of the gear, AE was measured in a bending fatigue process of a carburizing gear by using the power circurating-type machine and AE source location in gear teeth were required. By various analysis in these data, the AE characteristics in the fatigue damaging process of the gear tooth were determined.