• Journal of the Korean Wood Science and Technology
• /
• 제32권2호
• /
• pp.9-18
• /
• 2004

본 과제는 Spruce재가 사우나와 같은 고온 공간용 부재(部材)로 사용되어질 때 나타나는 수지삼출의 문제점을 해결하여 그 방안을 제시코저 수행하였다. 건식(乾式)공간용 부재(部材)의 경우 적절한 열기건조가 이루어진다면 별도의 처리를 실시하지 않더라도 110℃의 수지삼출 안정선을 얻을 수 있는 것으로 확인되었으며, 고주파진공건조에 의해 수지삼출 안정선이 열기건조보다 약 20℃ 정도 더 상승하였다. 습식(濕式)폭로시험에서는 저압증기폭쇄처리재의 경우 열기건조재나 고주파진공건조재 모두 수지가 전혀 삼출되지 않은 반면에, 무처리재의 경우 건조방법에 관계없이 130℃ 이상의 폭로조건에서는 수지삼출의 정도가 건식(乾式)폭로시험의 경우보다 심한 것으로 나타나, 수지삼출을 예방하기 위하여 인공건조중 저(低)함수율 상태의 건조말기에 고온(高溫)을 적용하여 건조하는 것보다는 건조전 고(高)함수율 상태에서 과열(過熱)증기로 분무(噴霧)처리하는 것이 더 바람직한 것으로 확인되었다.

• 펄프종이기술
• /
• 제41권1호
• /
• pp.1-8
• /
• 2009

Mountain Pine Beetle (MPB) attacked pine was evaluated for pulp quality, chemical and physical properties, and bleachability. Chemical analyses showed that the dehydroabietic acid and total acetone extractives content were higher in the year 3 (grey) attacked MPB chips and lower in the year 5 (grey) attacked MPB chips as compared to a typical SPF (spruce/pine/fir) reference. Lignin and carbohydrate content of the MPB wood chips were comparable to the SPF. Similarly, there was little difference in kappa number, pulp yield and liquor consumption between the 3 and 5 year MPB attacked wood. Likewise there was no significant difference in the resulting tear strength, burst, or tensile strength. There appeared to be an improved bleaching response in the MPB attacked pulp as compared to the SPF reference, but this was accompanied by a slightly lower bleached pulp yield and higher bleach filtrate COD and solids content.

• Journal of the Korean Wood Science and Technology
• /
• 제19권4호
• /
• pp.80-84
• /
• 1991

Lignocellulosic biomass including acetosolv ricestraw and spruce lignin were liquefied and converted into liquid hydrocarbons by catalytic hydroliquefaction reaction. These experimental works were carried out in 1-liter-capacity autoclave using 50% tetralin and m-cresol solution respectively as soluble solvent and Ni. Pd. Fe and red mud as catalyst. $H_2$ gas was supplied into the reactor for escaltion of deoxhydroenolysis reaction. Catalyst concentrations were 1 % of raw material based on weight. The ratio between raw materials and soluble solvent are 1g and 10cc. The reaction conditions are 400-$700^{\circ}C$ of reaction temperature, 10-50 atms of reaction pressure. The highest yield of hydrocarbon, so called "product oil" showed 32% and 5.5% of lowest char formation when red mud was used as catalyst. The product oil yields from those of other catalysts were in the range of 20-29%. The influence of different initial hydrogen pressures was examined in the range d 30-50 atms. A minimum pressure of 35 atms was necessary to obtain a complete recovery of souble solvent for recycling.

• Journal of the Korean Wood Science and Technology
• /
• 제26권3호
• /
• pp.16-25
• /
• 1998

This study was carried out to compare vibrational properties and adsorption among shellac, cashew finished plate and untreated plate of Sitka spruce(Picea sitchensis Carr). By the method of statistical regression modeling, the fundamental resonance frequency of finished plate was higher than that of untreated plate. The fundamental resonance frequency of cashew finished plate was higher than that of shellac finished plate. By the method of modal analysis, mode frequency ratio of cashew finished plate was higher than that of shellac finished plate. Amounts of adsorption of finished plate was lower than that of untreated plate, and amount of adsorption of cashew finished plate was lower than that of shellac finished plate. It was clarified that the vibrational properties and adsorption of finished plate were superior to those of untreated plate. The vibrational properties and adsorption of cashew finished plate was superior to those of shellac finished plate.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.57-65
• /
• 2005

Following our previous reports for finger-jointed woods with various finger profiles studied for the efficient use of small diameter logs and woods containing various defects, twelve types of finger-jointed woods glued with three kinds of adhesives and with two sizes of finger pitches were made with sitka spruce and red pine. The effects of the adhesives and finger pitches on bending creep performances of finger-jointed woods were investigated. The shape of creep curves differed among the used adhesives and finger pitches of finger-jointed woods for both tested species. Their creep curves showed a linear behavior beyond about one hour, and the N values fitted to power law increased with increasing finger pitches. The initial deformation increased with increasing finger pitches, regardless of the tested species and kinds of adhesives, whereas the effect of finger pitches on the creep deformation was not clear. For finger-jointed woods glued with polyvinyl acetate (PVAc) resin, creep failure occurred in 106 hours after the load was applied. And the difference of the creep compliance between finger-jointed woods glued with resorcinol-phenol formaldehyde (RPF) resin and aqueous vinyl urethane (AVU) resin was small. The ratios for creep performances of finger-jointed woods glued with RPF resin and AVU resin versus solid wood were higher in creep deformation than initial deformation for both species, and the difference between both adhesives was not found. The relative creep decreased with increasing finger pitches, and the marked differences was not found between RPF resin and AVU resin.

• Journal of the Korean Wood Science and Technology
• /
• 제34권6호
• /
• pp.36-43
• /
• 2006

유동형 급속열분해기 (fluidized bed type fast pyrolyzer, 용량 400 g/h)를 이용하여 너도밤나무와 침엽수 혼합재(독일가문비나무/전나무, 50:50) 에서 바이오오일을 생산하였다. 목질바이오매스의 열분해는 약 $470{\pm}5^{\circ}C$에서 1~2초 동안 진행되었다. 목질바이오매스의 열분해 생성물의 조성은 너도밤나무의 경우 바이오오일 60%, 탄 9% 그리고 가스가 31% 정도 생산되었으며, 침엽수 혼합재는 바이오일 49%, 탄 9%, 그리고 42% 가량의 가스가 생성되었다. 두 종류의 목질바이오매스에서 생산된 바이오오일의 수분함량은 약 17~22%이었으며, 밀도는 수종에 관계없이 $1.2kg/{\ell}$이었다. 바이오오일의 원소 조성은 탄소 45%, 산소 47%, 수소 7%, 그리고 질소 1%로 일반적인 목질바이오매스와 큰 차이는 없는 것으로 나타났다. 그러나 화석자원에서 생산되는 오일류와 비교하여 바이오일은 산소함량이 매우 높았고 황은 전혀 포함되어 있지 않았다. 바이오오일의 GC 분석 결과 총 90여종의 방향족(aromatic) 또는 비방향족(non-aromatic) 저분자량 화합물이 검출되었으며 이들의 함량은 바이오오일 전건중량의 31~33%로 분석되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제33권3호통권131호
• /
• pp.45-52
• /
• 2005

북양젓나무(Abies sibirica Ledeb)의 목분, 목섬유, 수피를 탄화하여 획득한 목탄의 물성과 흡착특성을 탄화온도별로 조사하였다. 전체적으로 탄화온도가 상승할수록 탄화수율은 감소하였다. 목탄의 탄소함량은 탄화온도의 상승과 함께 증가하였으나, 수소나 산소의 함량은 감소하였다. 수피탄화물은 목분 또는 목섬유 탄화물과 비교하여 탄화수율이 높게 나타났으며, 수피탄화물 내 회분함량도 상당히 높았다. 목질탄화물의 요오드흡착능은 탄화온도가 높을수록 향상되었으며, 목분이나 섬유 탄화물이 수피탄화물보다 상대적으로 높았다. 기상의 톨루엔에 대한 흡착능은 목탄 종류에 관계없이 $600^{\circ}C$에서 탄화하였을 경우 가장 높게 나타났으며, 이러한 결과는 $600^{\circ}C$에서 생산한 목탄이 비표면적과 총세공용적이 가장 크다는 사실로 쉽게 설명되어진다. 초산가스제거율은 고온탄화물일수록 크고, 암모니아 가스 제거율은 $400^{\circ}C$와 같은 저온에서 탄화한 탄화물이 높은 경향을 나타내었다. 이는 고온탄화물일수록 알칼리성을 나타내는 반면 저온탄화물은 산성을 나타내는 것에 기인하는 것으로 보인다. 따라서 목탄의 pH가 산 또는 염기성 가스 흡착능력에 큰 영향을 주는 것으로 생각된다.

• Journal of the Korean Wood Science and Technology
• /
• 제39권5호
• /
• pp.444-450
• /
• 2011

The goal of this study is to investigate bending properties of domestic timber. Three representative structural timber from Larix kaempferi, Pinus koraiensis, and Pinus densiflora, in the northeastern South Korea were selected. Visual grading for the timber was conducted based on KFRI notification 2009-01 and the bending strength for the timber was evaluated based on ASTM D 198 bending. The high percentage of grade 1 and 2 for Larix kaempferi shows that the KFRI notification was optimized for this species. The bending strength distributions from Pinus koraiensis and Pinus densiflora were very similar. It could be possible to specify the allowable bending properties of these two Specification using a united species group similar to spruce-pine-fir. Lastly, the bending strength of $120{\times}180mm$ structural members was higher than both existing values in KBC 2009 and design values for timber of imported species described in the NDS. Thus, 120 mm thick domestic softwoods could replace the commercial imported species and the KBC should be modified to provide design values for both timber and dimensional lumber, respectively, like NDS.

• 건축역사연구
• /
• 제16권1호
• /
• pp.9-28
• /
• 2007

We investigated the changes in the species of the woods used for Korean ancient and historic architectures, which include prehistoric excavated relics and existing wooden buildings in South Korea. The species data were collected from various sources such as excavation and repair reports, journal papers, and a few unpublished documents. We divided the building Periods as Paleolithic, Neolitic, Bronze Ages, Iron Age/Three Kingdoms, Koryo, Joseon (early, middle, late) and modem periods. In prehistoric periods, hardwoods were major species. Oak (Quercus spp.) woods dominated (94 percent in average); the others (5%) were Juglans mandshurica, Platycarya strobilacea, Castanea crenata, and few softwoods(1%). During Iron Age and Three Kingdom periods, oaks remained as a major species (57%) and others Platycarya strobilacea(21%), Castanea crenata(13%), and Pinus spp. (6%). The oak woods decreased in Koryo period and they occupied only 1.1%. Instead of oaks, pine (Pinus spp., 71%) and Zelkova serrata (22%) dominated in Koryo. In early and middle Joseon periods, pine woods (73%) remain as a major species and the others were oaks (14%) and Zelkova serrata (9%). As late Joseon came, the pine woods occupied more than 88%. In the late 19th and early 20th centuries, a few boreal species such as larch (Larix spp.) and spruce (Picea spp.), which grow in cold area, were found. We believe they were transported from northern Korea. The existing buildings in Korea are mainly from Joseon period and a few from late Koryo periods. During these periods, pine woods were used for most buildings. For such reason, pine woods were known as 'representative materials for historic buildings'. but earlier times, broad-leaved trees, i.e., oak and Zelkova woods were major materials. The changes in building materials resulted from both climate and human impacts. The dry climate and disturbed forests induce more pines in the mountains. We also compared the wood qualities of the species and found that Zelkova woods were superior ones and deserved more planting for future demands in the repair for historic buildings.

• Journal of the Korean Wood Science and Technology
• /
• 제51권3호
• /
• pp.197-206
• /
• 2023

A truss is a structure in which the members are connected and arranged such that they are primarily subjected to axial loading. A truss has the advantage that it can be used for a longer span because the structure distributes the applied force to its members well, and the load is transmitted only in the axial direction of the members. Trusses manufactured using timber have more advantages than those made of other materials. In this study, the properties of parallel chord trusses composed of timber chord and steel-web members were evaluated. We constructed truss specimens with various lengths by using upper and lower chords of 2 × 4 inch spruce-pine-fir lumber and steel-web members manufactured by S and P companies. The specimens were tested in accordance with KS F 2150. The test results showed that the load at the deflection limit and the deflection limit itself increased from L/180 to L/360 regardless of the length of the specimens. For specimens of the same length, the load at the deflection limit increased as the height of the parallel timber chord truss specimens increased from 200 to 300 mm. Successive installations of the steel-web members (SST) showed almost 2 times the load at each deflection limit compared to that of SAT specimens (alternate installation of the steel-web members). When comparing the three load-deflection limits in terms of the manufacturer of the steel-web members, the load at each deflection limit for SST specimens was higher than that for PST specimens.