• New & Renewable Energy
• /
• v.2 no.2 s.6
• /
• pp.94-101
• /
• 2006

[ $1m^3$ ] solid hydrate contains up to $200m^3$ of natural gas, depending on pressure and temperature. Such large volume of natural gas hydrate can be utilized to store and transport large quantity of natural gas in a stable condition. So, in the present investigation, experiments carried out for the formation of natural gas hydrate governed by pressure, temperature, and gas compositions, etc.. The results show that the equilibrium pressure of structure II natural gas hydrate) is approximately 65% lower and the solubility is approximately three times higher than structure I methane hydrate). Also, the subcooling conditions of the structure I and II must be above 9K and 11K in order to form hydrate rapidly regardless of gas components, but the pressure increase is more advantageous than the temperature decrease in order to increase the gas consumption. And utilizing nozzles for spraying water in the form of droplets into the natural gas dramatically reduces the hydrate formation time and increases its solubility at the same time.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.31-36
• /
• 2010

A small unmanned helicopter was suggested to replace the conventional spray system. Aerial application using an agricultural helicopter helps precise and timely spraying, and reduces labor intensity and environmental pollution. In this research, a rotor system (SW05) was developed and its lift capability was evaluated. Lift force for the dead weight of the helicopter was obtained at the grip pitch angle of $12^{\circ}$. As the pitch angle increased to $14^{\circ}$ and $16^{\circ}$, the payload increased to 176 N and 216 N, respectively. Compared with SW04 airfoil performance in the total lift, the SW05 airfoil showed nearly the same capacity, but the payload of the SW05 was reduced because of the increased dead weight. A rated flight condition was defined as lifting mean payload of 294 N with the grip pitch angles of $16{\sim}17^{\circ}$ at the rotor rotating speed of 850~950 rpm for the adjusted engine power. The fuel consumption would be 4.8~6.0 L/hr, and the air temperature of cooling fan should be kept below $160^{\circ}C$.

• Journal of Biosystems Engineering
• /
• v.33 no.5
• /
• pp.289-295
• /
• 2008

The task of chemical spraying has been seriously considered as an irritating and annoying job for Korean rice farmers. An agricultural unmanned helicopter was suggested to solve this problem so as the farmers to have more decent farming condition. The objectives of this study were to analyze the adoptability of an experimental rotor blade (SW05) using the CFD simulation and also to compare the simulation results with experimental results. The simulation results showed that the induced power of this rotor reached to $57{\sim}63%$ of total power and the profile power was about $37{\sim}43%$ of total power. Therefore it can be concluded that this rotor's performance characteristics were not so efficient for the size of unmanned helicopter due to the low induced power and high profile power relatively compared with ones of conventional rotors. The comparison with experimental results showed that the tested lifts were less than 70% of simulated ones at the grip pitch of $12^{\circ}$ and decreased to 40% at the $18^{\circ}$ grip pitch. Therefore, it can be concluded that the rotor was too oversized to be used for a 15.4 kW (21 PS) engine.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.2
• /
• pp.193-201
• /
• 2011

Clamp type transferring mechanism for package substrate's wet processes was newly developed instead of conventional roller type transferring mechanism. Clamp type transferring mechanism has the advantages of reducing the panel deflection and of minimizing the contact problem between the panel and the transferring mechanism. Individual clamp of the mechanism has two distinct mechanical functions which are perfectly fixing a panel during the transferring and generating adequate tension for the panel. To determine the mechanical parameters of the clamp, panel deflection simulation was conducted and the result was verified by the panel deflection measurement. Also, fixing angle of a clamp could be determined by the free body force analysis of individual clamp. Finally clamp type transferring mechanism was actually manufactured and the transferring performance was verified during the water spraying condition of the package substrate's wet processes.

• Journal of ILASS-Korea
• /
• v.25 no.2
• /
• pp.81-88
• /
• 2020

Electrospray is used in various industries because it can produce continuous and uniform droplets. However, it is difficult to find optimal spraying condition due to lack of data in various conditions. In this study, various conditions were divided into electric parameters and fluid property. The electric parameters set Nozzle to Substrate(NTS), nozzle diameters and the fluid property set viscosity and conductivity as conditions. In this study, it observes spray patterns, Sauter Mean Diameter(SMD) according to conditions. As a result, fluid properties had a greater effect on the cone-Jet mode than on the nozzle diameter, NTS, and flowrate. All of solutions have Stable cone-jet mode at voltage of 8.5 kV, NTS of 20 mm and nozzle diameter of 0.2 mm. SMD has 27% different depending on viscosity and conductivity. The increased flowrate and viscosity are rising break-up length and thickening jet also jet is thinned by increased conductivity. Experiments have confirmed that the jet is thickened by increased flowrate and viscosity, and that the jet is thinned by conductivity.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.437-443
• /
• 2005

Controlling the friction between wheel and rail is direct and very effective measures to improve the curving performances of railway trucks, because the curving performances depend much on friction characteristics. Authors have proposed a method, 'friction control', which utilizes friction modifier ($KELTRACK^{TM}$ HPF) with onboard spraying system. With the method, not only friction coefficient, but also friction characteristics can be controlled as expected. In this study, MBD simulation is very valuable tool to foresee the effect of the control in advance of experiment with real car. And the creep characteristics of wheel/rail contact with the friction modifier takes very important role in the simulation. In this paper, authors propose a theoretical model of wheel/rail contact condition considering the creep characteristics of friction modifier, which is derived the application of principle tribological theories.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.35-39
• /
• 2008

In this study, electromechanical properties of carbon nanotube (CNT) thin film on flexible substrates were measured using a micro-tensile machine with functionality of simultaneous measurements of displacement, load and electrical resistance. The CNT thin film of about 100 nm thick was deposited on flexible substrates, polyethylene terephthalate (PET) using spraying and ink-jetting techniques. To investigate the effect of process condition on the electromechanical properties of CNT thin film, sets of CNT samples were fabricated under various heat treatments and microwave process. The microstructures of the CNT thin film before and after tensile test were investigated using Scanning Electron Microscope (SEM), and the failure modes of the CNT thin films were identified to understand their electromechanical behaviors and interaction with the flexible substrates. Based on the experimental results, the use of CNT thin film as flexible electrodes and strain gages is discussed.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.234-242
• /
• 2009

This study was attempted to develop surface washing-system of ginseng. The effect of sterilization, washing and keeping freshness of ginseng through analyzing unit process were examined to establish optimal condition for washing system. Surface washing method of fresh ginseng used two way and full cone spray type. Sterilization was used at $2^{\circ}C$ water with electrolysis water of 50 and 80 ppm. Ginseng was sterilized with electrolysis water during 30 and 60 s, dehydrated during 1 min and dried during 1min at 30 and $50^{\circ}C$. Hardness of surface-washed ginseng showed good result on 1 min spraying time with 80 ppm electrolysis water at $10^{\circ}C$ storage. Ginseng with 80 ppm electrolysis water was sterilized better with $1.05{\times}103$. There are no changes with 0% on appearance quality at 80 ppm electrolysis.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.67-74
• /
• 1979

This survey was carried out to grasp the actual condition of a power tiller utilization . Now, the power tiller has become the leading machinery in the field of agriculture throughout the country . Two hundred farm houses, located in the provincial districts of Kimcheon and kum0rung, hav etaken part in the survey from October 1, 1976 to September 30, 1977. The results are summarized as follows . 1. The average size of cultivated land of a farm household in the districts surveyed was 1.77ha which was bigger than that of whole country. And the average age of power tiller drivers was analyzed in which only 105 of total drivers was on their 30's. 2. Distribution of a power tiller utilization was appeared to be 34.4% for transporting , 24% for tilling , 23% for pumping , 11.5% for threshing and 6.6% for spraying. 3. Frequency of a power tiller utilization was high during the month of June, July and October while it was low during February and December . 4. Distribution of repairing cost was 8.5% for trailer, 7.1% for throttle lever and 6.7% for casket, respectively. The annual cost for repairing was 5,290 won.5. The annual cost for using a power tiller was composed of 51.5% of fixed cost and 48.5% of operating cost. 6. Economic analysis showed that it was not economically practical for individual ownership of a power tiller on the farm surveyed. Therefore, custom operation and joint ownership by a few farmers were recommended.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.4
• /
• pp.285-297
• /
• 1997

Finned segment, with which are lined inner wall of the turbine combustors, are subject to severe degradation when they are exposed to a hostile environmment at elevated temperature. To protect the finned segment from this environment and to maintain good mechanical properties of components at high temperature, they are preferred to be coated. The most governing factor for the durability of coatings used in the high temperature is the microstructure of coatings; these are splat from, distibution of microcacks, size and distribution of pores, thickness of coating layer, adhesion between coating layer, and oxidation of band coating. In this study, based on the evaluation of the imported finned segment, new finned segment segment was manufactured with optimum plasma spraying parameters, and their properties were examined. Using $ZrO_2(8wt$Y_2O_3)$,/TEX> powder for ceramic coating and 67Ni-22Cr-10Al-0.5Y mixing powder for bond coating, thickness of ceramic and bond coating layer were varied in order to find optimum condition, the results showed that B2T4(bond coating : 100~250$\mu\textrm{m}$, ceramic coating : 250~300$\mu\textrm{m}$) was the best among the specimens tested. Compared to the imported finned segment, B2T4 has better bond strength, hardness, and isothermal and cyclic oxidation resistance.