• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.1
• /
• pp.279-288
• /
• 2003

This study is the development of method on repairing concrete structure for progressing the durability of reinforced concrete. This method is wet spray method which compress and conduct mortar pre-mixed with polymer powder to hose by high pressure pump and spray it on the section of concrete structure through nozzle made specially. Characters of this method are that materials are selected with the sort of structure and the cause of deterioration and macro pores are removed in repaired section by conducting with high pressure and spraying with high velocity for progressing the durability of concrete structure. This study has carried out that the minimum capacity of rebound was measured with various condition and physical properties of sample made by spray method were estimated in comparing with sample made by previous hand method. Also, properties of long-term have carried out after this method was applied on site. According to experimental study, the capacity of rebound showed below 5% and physical properties of sample made by spray method were superior to that of sample made by hand method and physical and durable properties of long-term showed excellence.

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.393-401
• /
• 1997

Commercial flake graphite cast iron substrate was coated with titanium powder by low pressure plasma spraying and was irradiated with a $CO_2$ laser to produce the wear resistant composite layer. From the experimental results of this study, it was possible to composite TiC particles on the surface layer by direct reaction between carbon existed in the cast iron matrix and titanium with thermal sprayed coating by remelting and alloying them using laser irradiation. The cooling rate of laser remelted cast iron substrate without titanium coating was about $1{\times}10^4$ K/s to $1{\times}10^5$ K/s in the order under the condition used in this study. The microstructure of alloyed layer consisted of three zones, that is, TiC particule crystallized zone (MHV $400{\sim}500$), the mixed zone of TiC particule+ledebulite (MHV $650{\sim}900$) and the ledebulite zone (MHV $500{\sim}700$). TiC particules were crystallized as a typical dendritic morphology. The secondary TiC dendrite arms were grown to the polygonized shape and were necking. And then the separated arms became cubic crystal of TiC at the slowly solidified zone. But in the rapidly solidified zone of fusion boundry, the fine granular TiC particules were grouped like grape.

• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.494-501
• /
• 1997

In order to manufacture large rod preforms of 2014 Al alloy with a good mechanical property by spray forming method, it was spray-formed at a droplet temperature of $715^{\circ}C$, a droplet flight distance of 400mm, and a spraying angle of $35^{\circ}$. The rod preforms were extruded at $397^{\circ}C$ with the die temperature of $420^{\circ}C$ under the hot extrusion ratio 21:1 and T6 heat treatment was performed. The 2014 Al alloys cast by hot top process were also extruded and heat-treated at the same condition as a reference material. Microstructural observation and tensile test were carried out to investigate the effects of extrusion on microstructure and mechanical property of spray-formed Al alloy. Spray-formed Al alloys had many porosities due to inappropriate process conditions such as long droplet flight distance and low droplet temperature but have fine equiaxed grain. These porosities were reduced with decreasing in grain size by hot extrusion. Ultimate tensile strength and yield strength of spray formed-extruded 2014 Al alloy were inferior to those of the normal cast-extruded 2014 Al alloy, but elongations were superior. The control of porosity was important to get spray formed preform with a good mechanical property.

• Transactions of Materials Processing
• /
• v.21 no.1
• /
• pp.58-66
• /
• 2012

The work roll surface temperature rises and falls repetitively during hot slab rolling because the work roll surface is cooled continuously by water. This study focused on Std. No. 7 to determine a cooling method which significantly reduces the tangential tensile stresses on the work roll surface of the hot slab mill at Hyundai Steel Co. in Korea. A series of finite element analyses were performed to compute the temperature distribution and the tensile stresses in the circumferential direction of the work roll. The virtual slab model was used to reduce the run time considerably by assigning a high temperature to the virtual slab. Except for the heat generated by plastic deformation, this is equivalent to the hot rolling condition that a high temperature slab (material) would experience when in contact with the work rolls. Results showed that when the virtual slab model was coupled with FE analysis, the run time was found to be reduced from 2000 hours to 70 hours. When the work roll surface cooled with a certain on-off patter of water spray, the magnitude of the tangential stresses on the work rolls were decreased by 54.1%, in comparison with those cooled by continuous water spraying. Savings of up to 83.3% in water usage are possible if the proposed water cooling method is adopted.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.399-402
• /
• 2006

[ $1m^3$ ] solid hydrate contains up to $200m^3$ of natural gas, depending on pressure and temperature. Such large volume of natural gas hydrate can be utilized to store and transport large quantity of natural gas in a stable condition. So, in the present investigation, experiments carried out for the formation of natural gas hydrate governed by pressure, temperature, and gas compositions, etc.. The results show that the equilibrium pressure of structure II natural gas hydrate (is approximately 65% lower and the solubility is approximately three times higher than structure I methane hydrate). Also, the subcooling conditions of the structure I and II must be above 9K and 11K in order to form hydrate rapidly regardless of gas components, but the pressure increase is more advantageous than the temperature decrease in order to increase the gas consumption. And utilizing nozzles for spraying water in the form of droplets into the natural gas dramatically reduces the hydrate formation time and increases its solubility at the same time.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.621-626
• /
• 2006

Regenerative evaporative cooling is known as an environment-friendly and energy efficient cooling method. A regenerative evaporative cooler (REC) consisting of dry and wet channels is able to cool down the air stream below the inlet wet-bulb temperature. In the regenerative evaporative cooler, the cooling effect is achieved by redirecting a portion of the air flown out of the dry channel into the wet channel and spraying water onto the redirected air. In this study, a horizontal regenerative cooler is considered. In the horizontal regenerative cooler, the flow direction of evaporating water has a right angle to the flow direction of supply air. This difference was investigated with visualization technique and simplified 2-module performance test was done in a thermo-environment chamber. Optimum design configuration is changed due to the wet channel which are easily fully covered with evaporating water and block the air flow inside the channel. Applying the optimized fin configuration design with the highly wetting surface treatment, a regenerative evaporative cooler was fabricated and tested to Identify the cooling performance improvement and operation characteristics. From the experimental results at the intake condition of $32^{\circ}C$ and 50% RH, the supply temperature was measured to be around $23.4^{\circ}C$. The cooling effectiveness based on the inlet dewpoint temperature was evaluated 73% which is almost close to the design expectation.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.15 no.3
• /
• pp.149-157
• /
• 2020

Regarding previously-developed drone simulators, it was easy to check their flight stability or controlling functions based on the condition that their weight was fixed from the design. However, the drone is largely classified into two types that is the one with the fixed weight whose purpose is recording video with camera and racing and another is whole weight-variable during flight with loading the articles for delivery and spraying pesticide though the weight of airframe is fixed. The purpose of this thesis is to analyze the structure of drone and its flight principle, suggest dynamics-model-based simulator that is capable of simulating weight-variable drone and develop the simulator that can be used for designing main control board, motor and transmission along the application of weight-variable drone. Weight-variable simulator was developed by using various calculation to apply flying method of drone to the simulator. First, ground coordinate system and airframe-fixing coordinate system were established and switching matrix of those two coordinates were made. Then, dynamics model of drone was established using the law of Newton and moment balance principle. Dynamics model was established in Simulink platform and simulation experiment was carried out by changing the weight of drone. In order to evaluate the validity of developed weight-variable simulator, it was compared to the results of clean flight public simulator against existing weight-fixed drone. Lastly, simulation test was performed with the developed weight-variable simulation by changing the weight of drone. It was found out that dynamics model controlled various flying positions of drone well from simulation and the possibility of securing the optimum condition of weight-variable drone that has flying stability and easiness of controlling.

• Applied Biological Chemistry
• /
• v.32 no.3
• /
• pp.255-264
• /
• 1989

The minimum concentrations of organic solvents inducing phytotoxicity were investigated after spraying or flooding solvent solutions to annual plants. In the foliar treatment of upland test, solvents with high-boiling point or low-polarity induced severe phytotoxicity. Especially, aromatic solvents induced severe phytotoxicity. The most sensitive plant to phytotoxicity was soybean. In the pre-emergence treatment of upland test, the solvents with high-boiling point only induced phytotoxicity at high concentration. The degree of phytotoxicity induced by foliar spray in the condition of paddy field was similiar to that of upland test, but in the pre-emergence test, the former was more severe than the latter. Among 6 treatments, phytotoxicity induced by solvents was most severe in the pre-emergence test under the condition of flooding paddy field. Generally, alcohols induced severe phytotoxicity, especially, ethanol at 0.001%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3296-3301
• /
• 2011

The Porous pavement gains popularity because of several benefits. It is to minimize hydro-planning condition, spraying condition, and splash to increase friction resistance, and decrease noise. Also, other studies showed that it is important to have appropriate porosity to reduce noise and water flush. The purpose of this study is an evaluation on the mechanical properties of asphalt pavements for surface course. In this study the specimen was manufactured using the Gyratory compactor in order to compact the strengthened surface course that involved the two-layer pavement. This study is conducted by using Marshall stability test(KS F 2377), Impact resonance test, Schmidt hammer test(KS F 2730), and the Uniaxial compression test(KS F 2314). Using the Uniaxial compression test and Schmidt hammer test, the values of compressive strength and bearing capacity were measured, and the modulus of elasticity for each specimen was respectively measured using the Uniaxial compression test, Impact Resonance test.

• Research in Plant Disease
• /
• v.20 no.1
• /
• pp.31-36
• /
• 2014

Alternative spraying was developed using fungicides and potassium phosphonate to control watermelon powdery mildew (WPM) caused by Sphaerotheca fusca under greenhouse condition. In 2010 trial, a total of 9 combinations of 6 fungicides which are legally registered in Korea and currently used on watermelon farms were tested for the control efficacy against WPM. Though the combination of chlorothalonil (Chl)-myclobutanil (My)-fenarimol (Fen)-hexaconazole (Hex) was the most effective (82.6%) in the first-year trial, it had the problem that My, Fen and Hex have the same mode of action. Therefore, in the second-year trial to improve the fungicide combination and to reduce fungicide application, fungicides and potassium phosphonate (P) combinations were tested for WPM control using 500 ppm aqueous potassium phosphonate solution which is both eco-friendly and showing different mode of action from the fungicides tested. The P-My-Fen-Hex applied at 10-day intervals provided relatively high control (75.6%), whereas Chl-My-Fen-P provided 31.8% control. To improve the control, fungicides and P were applied at 7-day intervals in the third-year trial. Though Chl-My-Fen-Hex provided the highest control (89.6%), P-My-Fen-Hex also provided relatively high control (83.5%) compared to 65.9 % control with Chl-My-Fen-P, which suggests that Chl-My-Fen-Hex could be replaced with P-My-Fen-Hex for WPM control.