• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.5
• /
• pp.743-749
• /
• 2010

Multi-nozzle spray painting procedure of the inorganic zinc shop primer was established in order to obtain uniform film thickness. The shop primer paint prevents the corrosion of steel block during shipbuilding. When the dry film thickness of shop primer is insufficient, rust will be generated on the steel block. Otherwise, thick coating of shop primer may be a problem of weld defect. So, it is important to obtain the uniform film thickness of shop primer. The uniformity of dry film thickness is affected by spray speed, distance from spray gun to target surface and overlapping span of spray path. In order to uniformly maintain coating thickness of shop primer, the coating procedure was established based on the correlation of shop primer spray variables.

• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.27-32
• /
• 2003

It is important to improve the efficiency of the existing small scale burner which used in agricultural product dry system and gardening dry system. In order to economize fuel Consumption and decrease the exhaust emission especially $CO_2$, the better design for the small scale burner is needed. Spray characteristics are the essential element for the design. Macroscopic spray characteristics such as spray angle and breakup length were measured. SMD which is contained the Microscopic spray characteristics was measured too. SMD was measured at 8mm, I2mm, I6mm downstream of the nozzle tip for both Hago and Danfoss nozzles by the Malvern Particle Sizer.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.43-52
• /
• 2014

Recent developing tendency of thermal spray for green automotive industry are studied by searching of NDSL, KIPRIS, ScienceDirect and so on. Spraying techniques such as plasma spray, microwave treatment, dry-ice blasting, HVOF thermal spray, cold spraying, aerosol deposition are introduced, further more spraying materials such as nano particles, intermetallic compound, TiAlN, TiC, Si-Al alloys are investigated.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.5
• /
• pp.433-439
• /
• 2012

Anticorrosive paint is the most widely used in shipbuilding and the dry film thickness is very important in terms of productivity and assurance of anticorrosive performance. However, it is difficult to achieve the recommended target film thickness because the dry film thickness depends on labor's skill in practice and is affected by a number of parameters, such as spray pressure, paint flow rate, tip size, spray distance, SVR(Solid Volume Ratio), etc. Present paper derives an empirical equation through the correlation analysis of parameters selected by spray experiments of anti corrosive painting in order to predict the coated status. Comparing the calculated results with practical data, we show that the empirical equation can successfully expect DFT(Dry Film Thickness).

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.4
• /
• pp.353-360
• /
• 2000

The purpose of this research is to find the fundamental data for the design and optimum operation condition for the disk atomization comparing the atomization characteristics of the modified straight vane type disk atomizer and the cup type atomizer widely used in the field of spray dry. First, the experimental comparison of the characteristics of $Na_2SO_4$ atomization has been carried out using the cup type disk atomizer and the three kinds of vane type atomization designed specially for the experiment. After the comparison of the experimental data of the $Na_2SO_4$ and raw milk have been conducted using vane type atomizer.

• Journal of Bio-Environment Control
• /
• v.1 no.2
• /
• pp.154-161
• /
• 1992

This experiment was carried oui to determine the relativeness between growth, yield characters and bio-informations as influenced by the spray and rest time intervals of nutrient solution. Tomato(Lycopersicon esculentum Mill.) were grown in aeroponic system on a misting schedule of continuously 60 sec, 30 sec and 10 sec at 10 min intervals with full strength Yamazaki's solution recommended for tomato production. The results obtained were as follows : 1. Leaf area was highest in the plot of 30 sec spray and 10 min rest while the forest one was the plot of 60 sec spray and 10 min rest. Growth characteristics in terms of dry weight of each organ, number of flower, number of flower setted and fruit dry weight were greater in the plot of 30 sec spray and 10 min rest than the other treatments. 2. The number of flower increased with decreasing dry weight but number of flower sorted was not significantly different among treatment except for the plot of 60 sec spray and 10 min rest. 3. Leaf dry weight and fruit dry weight were highly correlated so that 30 sec spray and 10 min rest plot which is the highest fruit dry weight showed the largest leaf area. Continuously sprayed plot reduced markedly the fruit dry weight compared with leaf area. Optimum spray and rest time of nutrient solution in the range of this experiment was determined as 30 sec spray and 10 min rest. 4. Solar radiation within glasshouse during daytime reduced severely compared with outdoor one and air temperature within greenhouse was higher than the leaf temperature of tomato plant. The changes of environmental factors, solar radiation, temperature were accompanied with the sensitive change of bio-informations of tomato leaf Especially differences of spray intervals of nutrient solution affected greatly to the changes of bio-informations : leaf water potential, stomatal resistance and leaf temperature etc. 5. The changing patterns of leaf growth as influenced by the spray and rest intervals of nutrient solution were closely related to the leaf water potential, stomatal resistance and leaf temperature. Feasibility was demonstrated that measurement of bio-information of tomato leaf as influenced by the change of environmental factors could be expected to the amount of growth and fruit yield.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.38 no.4
• /
• pp.297-303
• /
• 1993

Seedling emergence and .stand establishment in dry-seeded rice is unstable at present due to deep seeding, low temperature at seeding time, excessive drought or raining etc. This experiment was conducted to elucidate the effect of gibberellic acid(GA$_3$) on the seedling emergence and growth in dry-seeded rice. GA$_3$, IBA and Metalaxyl were treated by seed-soaking or-spray. Hwaseongbyeo, a japonica rice, was used. The seed-soaking treatment with GA$_3$ significantly increased the seedling emergence and plant height as compared with untreated seed. However, no difference was observed in IBA and Metalaxyl treatment. The optimum concentration of GA$_3$ to promote the seedling emergence and growth in dry-seeded rice was about 100ppm for seed-soaking and about 200ppm for seed-spray treatment. The seed-spray treatment of GA$_3$ with 200ppm promoted earlier and faster seedling emergence and elongated seedling height as compared with untreated seed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.245-250
• /
• 2003

This research conducted milling tests to study effects of cutting environment conditions of ball end mills on the characteristics of hard milling process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAIN coated were utilized in the cutting tests. Dry cutting without coolant and semi-dry cutting using botanical oil coolant were conducted and MQL (Minimum Quantity Lubricant) device was used to spray coolant. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that dry cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than MQL spray cutting did.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.45-52
• /
• 2004

This research conducted milling tests to study effects of cutting environment conditions of ball end mills on the characteristics of hard milling process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAlN coated were utilized in the cutting tests. Dry cutting without coolant and semi-dry cutting using botanical oil coolant were conducted and MQL(Minimum Quantity Lubricant) device was used to spray coolant. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that dry cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than MQL spray cutting did.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.111-116
• /
• 2006

Tribologcal property of the ceramics used in severe condition was investigated and both $Al_2O_3$ ball and Al/SiC composite made by thermal spray process[TSP] were used as a specimen in this study. Four kinds of material couple in ball and disk specimens were tested in the dry condition by using ball-on-disk type tribo-tester. Friction coefficient, surface roughness, wear rate, and photograph of the worn surface were investigated. Generally, High SiC contents[$40{\sim}50%$] specimens showed very low friction coefficient below 0.05 and little wear rate in dry condition. And also, low SiC contents[0%] specimens showed a moderate wear rate and high coefficient of friction at the same condition.