• Journal of ILASS-Korea
• /
• v.11 no.2
• /
• pp.59-68
• /
• 2006

Experimental results of the metal powder production with internal mixing, internal impinging and the atomizer coupled with substrate design are presented in this paper. In a test with internal mixing atomizer, mean powder size was decreased from $37{\mu}m\;to\;23{\mu}m$ for Pb65Sn35 alloy as the gas-to-melt mass ratio was increased from 0.04 to 0.17. The particle size further reduces to $16.01{\mu}m$ as the orifice area is increased to $24mm^2$. The micrograph of the metal powder indicates that very fine and spherical metal powder has been produced by this process. In a test program using the internal impinging atomizers, the mean particle size of the metal powder was decreased from $22{\mu}m\;to\;12{\mu}m$ as the gas-to-melt-mass ratio increased from 0.05 to 0.22. The test results of an atomizer coupled with a substrate indicates that the deposition rate of the molten spray on the substrate is controlled by the diameter of the substrate, the height of the substrate ring and the distance of the substrate from the outlet of the atomizer. This in rum determines the powder production rate of the spraying processes. Experimental results indicate that the deposition rate of the spray forming material decreases as the distance between the substrate and the atomizer increases. For example, the deposition rate decreases from 48% to 19% as the substrate is placed at a distance from 20cm to 40cm. On the other hand, the metal powder production rate and its particle size increases as the subsrate is placed far away from the atomizer. The production of metal powder with mean particle size as low as $3.13{\mu}m$ has been achieved, a level which is not achievable by the conventional gas atomization processes.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.442-449
• /
• 2015

The effects of coating parameters were investigated in wear resistance coatings of Diamalloy-406 on Inconel 718 to obtain an optimum coating condition by high velocity oxy-fuel spraying. The coating parameters, the flow rates of source gases (hydrogen and oxygen), the powder feed rate, and the spray distance, were designed by the Taguchi method. The optimal conditions were determined: oxygen flow rate 34 FRM, hydrogen flow rate 57 FRM, powder feed rate 35 g/min, and spray distance 7 inch. Friction coefficients of the coating and the substrate decreased with an increasing sliding surface temperature from $25^{\circ}C$ to $450^{\circ}C$. The friction coefficient of Diamalloy-4006 coating decreased as the sliding surface temperature increased from $0.43{\pm}0.01$ at $25^{\circ}C$ to $0.29{\pm}0.01$ at $450^{\circ}C$. The wear trace and wear depth of the coating were smaller than the substrate at all temperatures tested. The relationship between spray parameters and wear resistance was discussed extensively, based on the measured roughness, hardness, and porosity in each coating.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.683-689
• /
• 2012

This research was carried out to investigate the effect of installation spacing of subsurface drip irrigation pipe on the mineral content, nutrient uptake, yield of lettuce, water requirement for irrigation, and soil chemical properties in greenhouse cultivation. Semi-forcing and retarding culture were implemented in this experiment, with four treatments containing overhead spray irrigation and three subsurface irrigation lateral spacing intervals of 30, 40, 50 cm at a depth of 30 cm from soil surface, respectively. Each mineral content of lettuce grown under subirrigation system did not show significant difference between treatments, however the uptake of nutrients was lower at 50 cm-distance. The yield was largest in 30 cm-subirrigation (SI), followed by 40 cm-SI, overhead spray, and 50 cm-treatment. Water requirement for irrigation was highest in overhead spray, and it was in reverse proportion to the distance of irrigation pipes. $NO_3$-N content in the soil, at a depth of 10 cm, showed a higher value in 50 cm-SI, followed by 40 cm-SI, overhead spray and 30 cm-SI. Exchangeable K content was highest in 50 cm-SI, Mg was highest in 40 cm-SI, and Ca was lowest in 30 cm-SI. In conclusion, the lettuce yield was not different between 30 and 40 cm-SI, but water requirement for irrigation was lower as the distance of irrigation pipes was further. And it seems to be needed more precise research on this theme, because crop yield and the dynamics of soil minerals in subsurface irrigation can vary with the depth and distance of irrigation pipes, dripper, water flow depending on the soil texture, and plant response to soil minerals.

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.16-23
• /
• 2002

Electrostatic pressure-swirl nozzle for practical oil burner application has been designed. The charge injection method has been used in this design, where the nozzle consists of a sharp pointed tungsten wire as a charge injector and the nozzle body grounded. The spray characteristics of the nozzles have been investigated by using an insulating liquid, i.e. kerosene without active surface agent. Breakup length of liquid decreased with an increase in applied voltage and injection pressure, while the spray angle increased with an increased in both applied voltage and injection pressure. An empirical equations have been suggested to predict the breakup length for electrostatic pressure-swirl atomizer. The experimental result was within the range of the predicted equations. The SMD decreased between the ranges of 2.8 ${\sim}$ 33% when the conventional nozzle was compared to the electrostatic with -10 kV applied to the electrode at a radial distance from 5 to 20 mm.

• Journal of Powder Materials
• /
• v.6 no.3
• /
• pp.224-230
• /
• 1999

Oxide powders of $Cr_2O_3 \;and\;Cr_2O_3+3{\%}TiO_2$ were prepared by spray drying, plasma densification and fused+crushed processes. The oxide coating layers were made by plasma spray and characterized by microstructure, hardness, adhesion strength and relative density. The optimum spray distance for the high quality coatings by spraying dried powders was found to be 9cm. A small amount addition of $TiO_2\;in\;Cr_2O_3$ powder significantly improved coating characteristics by lowering the melting point of powders. The hardness and relative density of coating layers of the plasma densified powders were comparable to fused and crushed powders, however, the adhesion strength was much higher in the former case.

• Journal of ILASS-Korea
• /
• v.7 no.4
• /
• pp.23-31
• /
• 2002

In this study, the sizes and velocities of droplets in sprays were measured by image processing method from digital images of local region of sprays. The morphological method based on the Euclidean distance transform, Watershed separation, and perimeter image was adopted for the recognition and separation of overlapped particles. The match probability method was used for the particle tracking and pairing. The measurement results show that the present method may be reliable for the analysis of the motion and distribution of droplets produced by spray and atomization devices.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1534-1539
• /
• 2004

The objective of this study is to simulate the etching characteristics with oscillation angle for the optimization of etching system. The etching characteristics were analyzed under different etching conditions. The spray characteristics were measured by Phase Doppler Anemometer (PDA). The correlation between the spray characteristics and the etching characteristics was investigated and used for fundamental data to simulate the etching characteristics with oscillation angle. The smaller coefficient of variation, the more uniform etching characteristic distribution became. It was found that numerical predictions of etching factor generally agreed well with the measured results with distance from nozzle tip. Oscillation leads to decrease of etching factor and increase of uniformity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.79-87
• /
• 2024

This paper is a study on the optimal microdroplet generation conditions in indirect charging electrostatic spraying. Unlike the direct charging method, which applies power to the nozzle, the indirect charging method applies power to the discharge electrode between the nozzle and the collection electrode. Therefore, an electrically simplified system can be obtained by minimizing the insulation part a stable spray pattern can be obtained with a wide spray angle, and a stable spray pattern can be obtained with a wide spray angle. To conduct the study, an indirect charging type electrostatic spray visualization system was constructed and the static characteristics of the microdroplets were analyzed through image processing of the spray shape of the microdroplets. The total number of microdroplets and the number of microdroplets per power consumption are confirmed according to the changes in the distance between the discharge electrode and the collection electrode, the flow rate, and the applied voltage, which affect the generation of microdroplets, and using this, the optimal generation conditions are derived and the corresponding microdroplet size distribution was analyzed. As a result of the experiment, it was confirmed that the optimal generation condition was at a flow rate of 15 to 20 mL/min and a voltage of -22.5 to -25 kV in terms of the number of microdroplets, and at a flow rate of 15 to 20 mL/min and a voltage of -20 kV in terms of energy consumption efficiency.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.72-79
• /
• 2006

The objective of this work is to simulate the etching characteristics for the optimization on the etching process of Lead-Frame. The etching characteristics such as etching factor, etching uniformity were investigated under different the actual operating conditions. The correlation between the etching characteristics and the spray ones were analyzed to simulate the etching characteristics in the etching process. To improve the etching characteristics in the etching process, effects of the various operating conditions such as pressure, distance from nozzle tip, pipe pitch, and feed speed should be understood in detail. The spray characteristics obtained by experiment using PDA system were simulated by the Monte-Carlo simulation. The etching process model was coded by Java language. It was found that the spray characteristics were correlated with the etching ones and simulation results generally agreed well with the measured results of etching characteristics in the etching process of Lead-Frame. The optimal operating parameters were successfully found under variable conditions.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.287-292
• /
• 2015

The possibility of chemical precipitation for recycled ammonium paratungstate (APT) was studied. WO₃ particles were synthesized by chemical precipitation method using a 1:2 weight ratio of APT:DI-water. At the 500℃ sintering temperature, the X-ray diffraction results showed that APT completely decomposed to WO₃. For the granulated powder WC-Co, vacuum heat treatment at proper temperatures increases tap density and flow-ability. Hardness of the WC-Co thermal spray coating layer was measured in the range HV 831~1266. Spray conditions for the best characteristic values were an oxygen flow rate=1500 scfh, a fuel flow rate = 5.25gph and a gun distance = 320mm.