• Journal of Welding and Joining
• /
• 제7권3호
• /
• pp.55-62
• /
• 1989

Variation of the spray droplet velocity with spraying distance and the microstructural characteristics of spray deposits fromed by oxy-fuel thermal spraying with Ni-base alloy powder contained chrome boride for hard facing were examined. Measurements of spray droplet velocity as a function of distance from the nozzle tip were inexcellent agreement with computer simulated predictions. Optimum condition for thermal spray deposits in this experiment was found to be under #10kg/cm^2$ of acceleration gas pressure with 15cm of spraying distance. Fine microstructure and higher microhardness of the initial part of the deposits due to rapid solidification were found to be able to maintained in a thickness up to 0.4mm, and this initial microstructure and properties could be maintained throughout the thickness of a thick spray deposits by performing the multipass spraying with 0.4mm thickness of each pass.

• 한국분무공학회지
• /
• 제28권1호
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.

• 치위생과학회지
• /
• 제19권2호
• /
• pp.107-112
• /
• 2019

Background: Good oral health is important for systemic body health and quality of life. Spray oral cleansers are increasingly preferred because of their convenience of carrying and the ease of oral hygiene management. In addition, many kinds of oral cleanser products containing various ingredients with antibacterial, washing, and moisturizing effects are being manufactured. However, concerns about the safety and side effects of oral sprays are increasing, and there is very little information regarding the use and care of oral sprays is available to consumers. This study aimed to investigate the effects of oral spray on oral bacteria and tissue to elucidate the factors that need to be considered when using oral sprays. Methods: The effects of oral spray on the growth of dental plaque bacteria was assessed using disk diffusion assays. Cytotoxicity and morphological changes in oral epithelial cells were observed by microscopy. The effects of oral spray on dental plaque growth were also confirmed on specimens from permanent incisors of bovines by Coomassie staining. Results: The pH of spray products, such as Perioe Dental Cooling, Cool Sense, and Dentrix, were 3.65, 3.61, and 6.15, respectively. All tested spray products showed strong toxicity to dental plaque bacteria and oral epithelial cells. Compared with those on the control, dental plaque bacteria deposits on the enamel surface increased following the use of oral spray. Conclusion: Three types of oral spray, namely Perioe Dental Cooling, Cool Sense, and Dentrix, strongly inhibited the growth of dental plaque bacteria and oral epithelial cells. The oral spray ingredient enhanced dental plaque growth on the enamel surface. Users should be informed of precautions when using oral sprays and the need for oral hygiene after its use.

• Journal of Biosystems Engineering
• /
• 제29권1호
• /
• pp.21-28
• /
• 2004

Spraying is one of the most efficient methods for pesticide and insecticide control. Generally, orchard sprayers(aircarrier sprayer) are used for such applications. However, when an orchard sprayer is used, only 20% of total amount of spray deposits on the target. The rest of spray are not only wasted but are also potential sources of environmental pollution. The research far the development of electrostatic spraying system for orchard sprayer was conducted to develop the new pesticide application technology for the reduction of environmental pollution and f3r the production of safe agricultural products. The spray characteristics for nozzles with the different charging methods were tested and the effect of electrostatic charge was analyzed, in the laboratory experiments. The results of this study indicate that the capacitive type of electrostatic spraying nozzle exhibits a large current deposition of water sprays on the sample target. The covering area ratio by conventional spraying system was 10.2%, while that of electrostatic sprays with pulse induction charging method gave the increased covering area ratio by 4.3 times.

• 농약과학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2016

농약의 효율적인 방제효과를 얻기 위해서는 적절한 시기에 원하는 작물체의 부위에 균일하게 부착되도록 하는 것이 중요하다. 농약 살포기술(application technology)은 노즐의 형태 및 종류와 같은 미세 조절이 가능한 기계적인 인자가 약효 발현과 작물 잔류성에 영향을 미치는 중요한 요인으로 작용하고 있다. 본 연구에서는 감귤의 더뎅이병에 사용되는 디티아논 액상수화제를 이용하여 감귤 과원에서 사용중인 약제 살포방식 차이에 따른 감귤 잎의 부착량 분포도를 조사하여 살포 방식의 효율성을 비교하였다. 이를 위해 기계식 살포기를 대조구로 하고 노즐 및 살포 방식에 변화를 준 sprinkler 살포시스템 및 speed spray 분사 방법에 대한 감귤잎 부착량을 비교 평가하였다. 시험은 제주도에 위치한 감귤시험장 감귤과원에서 진행하였으며, 감귤잎의 높이 위치별 부착량, 전후면 부착량을 알아보기 위하여 디티아논 43% 액상수화제 1,000배 희석 액을 살포한 후 filter paper와 나뭇잎을 상, 중, 하로 높이로 채취하여 실험에 사용하였다. Speed spray 방식이 engine type spray 방식보다 부착량 및 부착균일성 우수하였고, 모든 살포방식이 잎 뒷면의 부착량을 증가 할 수 있는 방식으로 개선되어야 하며 감귤의 상부 위치의 부착량 평가에서는 마른안개 sprinkler 방식이 가장 우수하였다.

• 태양에너지
• /
• 제18권2호
• /
• pp.137-144
• /
• 1998

분무열분해법으로 $SnO_2$ 박막을 증착하여 기판표면의 온도에 따른 방향성과 결함을 조사하였다. 기판의 온도가 $300^{\circ}C$일 때부터 결정성 박막이 증착되었다. 기판의 온도가 $400^{\circ}C$까지 증가함에 따라 (200)면이 우선적으로 성장하였으며 결정립의 크기도 증가하였다. Sb를 첨가하지 않은 박막은 Sn과 O로 구성되어 있으며 산소공위를 포함한다. Sb를 첨가한 박막은 산소공위 외에 Sn 위치와 O 위치에 각각 치환된 Sb와 Cl을 가진다.

• Journal of Biosystems Engineering
• /
• 제26권5호
• /
• pp.431-440
• /
• 2001

Generated agri-chemical droplets by orchard sprayers are evaporated regenerated and transported along wind streams. The droplets are deposited to targets after changing their sizes, affecting the retention of droplets. An orchard sprayer, designed for spraying grapevines was studied on the spatial distribution of droplet size. The experimental variables were spray direction (0, 22.5, 45, 67.5 and 90˚), distance(2.5, 3.0 and 3.5 m) and fan speed (2,075 and 3,031 rpm). Droplet sizes were converted and analyzed from spray stains, sampled using water sensitive papers. The number median diameter (NMD) increased with an increase of the distance due to disappeared fine droplets (<50 ㎛): however, the volume median diameter (VMD) decreased due to shrunken large droplets (>100 ㎛). Fast fan speed delivered large droplets to 3.5 m, but the spatial distributions of NMD and VMD were not uniform. Slower fan speed decreased the possibility of evaporation and drift; therefore, plenty of droplets were maintained up to 3.0 m. The upward blasting distance was limited within 3 m, but the limit to the ground level was extended to 3.5 m. Concentrated wind and droplets to the ground level should be redistributed to upper canopy direction, leading more uniform deposits. High speed wind and system pressure should be avoided because of generating fine droplets, which would be disappeared and drifted away.

• Corrosion Science and Technology
• /
• 제6권5호
• /
• pp.257-260
• /
• 2007

In order to further improve the corrosion resistance and wear resistance of the Ni-P coatings of electroless plating, electroless Ni-P/n-$Al_2O_3$ composite deposits were prepared by adding some nano $Al_2O_3$ Particles in Ni-P plating bath. The bath composition and proproties were studied in this paper. The orthogonal test was applied in order to get the new composite solution, taking the initial stable potential as evaluation standard and considering the elements correlation at the same time. The processing parameters have been optimized by single factor experiment in which the depositing speed was chosen as the evaluation standard. The results showed that the process is stable and the composite Ni-P/n-$Al_2O_3$ deposits werebright and smooth, whose hardness and corrosion resistance are much better than simple Ni-P coatings. Furthermore the surface appearance and structure of the composite Ni-P/n-$Al_2O_3$ coating were investigated by SEM and XRD method. It was proved that the coating surface is typical cystiform cells and its structure is amorphous. All test results ofcomposite coating showed that all various physical coating properties had been improved by adding nano-particles. The hardness of optimal coating is more than 600HV and increases to 1000HV after heat-treating, and its hardness is 20~50% higher than Ni-P coating. The rust points appeared in 200 hour by immersing the coating into the 10%HCl solution and the corrosive speed is $3{\times}10^{-3}mg/(cm^2{\cdot}h)$which was obtained after 300 hour. In the same condition Ni-P coating is $5.6{\times}10^{-3}mg/(cm^2{\cdot}h)$. The salt spray resistance of the layers can exceed 600h with the thickness $20{\mu}m$.

• 한국분무공학회지
• /
• 제17권3호
• /
• pp.140-145
• /
• 2012

Recent common-rail injector of a diesel engine needs more smaller nozzle hole to meet the stringent emission regulation. But, small nozzle hole diameter can cause nozzle coking which is occurred due to the deposits of post-combustion products. Nozzle coking has a negative effect on the performance of fuel injector because it obstructs the fuel flow inside a nozzle hole. In this study DFSS (Design for six sigma) method was applied to find the effect of nozzle design parameter on nozzle coking. Total 9 injector samples were chosen and tested at diesel engine. The results show that nozzle hole diameter and K-factor have more effect on nozzle coking than A-mass and hole length. Large hole diameter and A-mass, small hole length and K-factor give more positive performance on nozzle coking in these experimental conditions. But, a performance about nozzle coking and exhaust gas emission shows the opposite tendency. Further study is needed to find the relation between nozzle coking and emission characteristic for the optimization of injector nozzle design.

• 농약과학회지
• /
• 제16권4호
• /
• pp.315-321
• /
• 2012

소나무재선충 매개충인 솔수염하늘소 방제용으로 살포되는 농약성분의 산림환경 중 분포, 이동 및 잔류소장 등 행적을 파악하고 방제지역으로부터 수계유출에 대한 평가를 목적으로 acetamiprid 액제와 imidacloprid 분산성 액제에 대한 행적실험을 경상남도 함안군 소재 산림에서 실시하였다. 농약의 살포량은 100배 희석액 50 L/ha이었는데 imidacloprid는 배량 시험을 추가하였고 Bell 206L 헬리콥터로 두 번 살포하였다. Acetamiprid의 평균 지표면 낙하량은 표준살포량의 2~4% 수준이었다. 솔잎 중의 잔류량은 살포 직후에 1.8~8.5 mg/kg이었으나 48일 후에는 1.2~2.1 mg/kg로 감소하였고, 빗물에 씻겨 내린 양은 살포량의 17% 수준이었다. 토양표면에 도달한 acetamiprid의 대부분은 부엽토층에 존재하였으며 살포 48일 후에는 표면도달량의 4분의 1 수준으로 감소하였고, 부엽토 밑 토양에서는 전 기간 동안 검출되지 않았다. Acetamiprid는 인접 소류지에서 비산에 의하여 0.0003 mg/L의 낮은 수준으로 검출된 외에는 검출되지 않았다. Imidacloprid의 평균 지표면 낙하량은 표준살포량의 1~3% 수준이었다. 솔잎 중의 잔류량은 살포 직후에도 0.1 mg/kg 수준에 불과하여 솔잎에는 수분과다 등의 원인으로 거의 부착되지 않은 것으로 판단되었으나, 목질부로부터 빗물에 씻겨 내린 량은 살포량의 4~8% 수준이었다. 토양표면에 도달한 imidacloprid의 대부분도 부엽토층에 존재하였으며 살포 111일 후에는 표면도달량의 20분의 1 수준으로 감소하였고, 부엽토 밑 토양에서는 살포량의 0.5% 미만으로 검출되었다. Imidacloprid는 계곡수에서 0.0003~0.0017 mg/L의 낮은 수준으로 검출되었으나 수계오염을 우려할 수준은 아니었다.