• Journal of Climate Change Research
• /
• v.7 no.3
• /
• pp.249-256
• /
• 2016

Porous $Al_2O_3$ hollow fiber membranes were successfully prepared by dry-wet spinning/sintering method. The SEM image shows that the $Al_2O_3$ hollow fiber membrane consists mostly of sponge pore structure. The contact angle and the breakthrough pressure were $126^{\circ}$ and 1.91 bar, respectively. This results indicate that the $Al_2O_3$ hollow fiber membranes were successfully modified to hydrophobic surface. The hydrophobic modified $Al_2O_3$ hollow fiber membranes were assembled into a membrane contactor system to separate $CO_2$ from a model gas mixture of the flue gas at elevated gas velocity. The $CO_2$ absorption flux was enhanced when the gas velocity increased from $1{\times}10^{-3}$ to $6{\times}10^{-3}$ m/s. Whereas the $CO_2$ absorption flux was decreased with the number of hollow fiber membrane of a module because of the concentration polarization. Furthermore, we developed an lab-scale $Al_2O_3$ hollow fiber membrane contactor modules and their system (i.e., $CO_2$ absorption using the $Al_2O_3$ membrane and monoethanolamine (MEA)) that could dispose of over $0.02Nm^3/h$ mixture gas (15% $CO_2$) with the removal efficiency higher than 95%. The results can be useful in a field of the membrane contactor for $CO_2$ separation, helping to design and extend a equipment.

• PNF and Movement
• /
• v.12 no.4
• /
• pp.209-215
• /
• 2014

Purpose: This study aims to understand the effect of balance training on ankle muscle activity and static balance in stroke patients. Methods: The subjects were composed of 12 patients who were admitted with chronic stroke in H, K, and R hospitals located in Gangwon-do from August to October 2014. This study conducted balance training on the subjects for 20 min a session, twice a day, five times a week for six weeks. This study measured the surface electromyogram (EMG) of the paretic side's tibialis anterior and medial gastrocnemius for muscle activity. Static balance was measured as a TETRAX stability index. The measurements were conducted before the experiment and six weeks after. The result was statistically analyzed using paired t-test at the significance level of 0.05. Result: Muscle activity of the paretic side's tibialis anterior and medial gastrocnemius did not show a significant difference in the comparison between pre- and post-balancing training. However, the stability index showed a significant difference (p<0.05) between standing with eyes open (NO) and standing on a sponge with eyes open (PO). Conclusion: Although balance training did not affect the muscle activity of chronic stroke patients, it had an effective influence on the stability index. That is, balance training was effective at the functional level, but it did not change the structure level in terms of the ICF evaluation standard. Balance training becomes more effective when it is applied in relation to task.

• Membrane Journal
• /
• v.24 no.2
• /
• pp.113-122
• /
• 2014

Porous poly(L-lactic acid)(PLLA) scaffold membranes were prepared via. phase separation process. Chloroform, dichloromethane and 1,4-dioxane were used as solvent and, ethyl alcohol was used as non-solvent. Morphologies, mechanical properties and mass transfer characteristics of the scaffold membranes were investigated through SEM, stress-strain test and glucose diffusion test. The scaffold membranes obtained from the casting solutions with chloroform and with dichloromethane showed similar morphologies. They showed sponge-like porous structure with the pore size in the range of $3-10{\mu}m$ and, their porosities were in 50-80% range. Using 1,4-dioxane as solvent, nano-fibrous scaffold membranes with porosities over 80% were fabricated. When the polymer content in the solution with 1,4-dioxane was lowered to 4%, highly porous, macroporous and nano-fibrous scaffold membranes were obtained. The size of the macropore was tens of the microns and the porosity was around 90%. These results indicate that the solvent has significant effect on the scaffold membrane structure and, that scaffold membranes with various structures can be fabricated through phase separation method by choosing solvent and by controlling polymer concentration in the casting solution.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.1-8
• /
• 2006

Anatomy of Quercus variabilis charcoal was investigated by scanning electron microscopy. Charcoal was prepared in an electric furnace under nitrogen gas atmosphere at $400^{\circ}C$, $600^{\circ}C$, $800^{\circ}C$, and $1000^{\circ}C$ for 10 min. The structure of charcoal was significantly affected by charring temperature. In cross section, charcoal prepared at $400^{\circ}C$ exhibited a smooth clean surface. As the charring temperature increased, the surface became more rough and increasingly disrupted. The cell walls appeared homogeneous and glass-like. Ray parenchyma cells showed very little separation from each other in radial section at $400^{\circ}C$. At $600^{\circ}C$ and above there is an apparent disintegration of the middle lamella, resulting in a separation of the ray cells. The $2{\sim}4{\mu}m$ wart-like protuberances were observed on the surfaces of the parenchyma cells. These structures were seen in charcoal prepared at all temperatures. Distinctive features can be seen in multiseriate rays as large crack and split. Rhomboidal crystals in crystalliferous cells had a smooth surface at $400^{\circ}C$ and $600^{\circ}C$, but the crystals had a sponge like appearance at $800^{\circ}C$ and $1000^{\circ}C$.

• Journal of Korean Society of Forest Science
• /
• v.101 no.4
• /
• pp.613-618
• /
• 2012

The 5-year-old seedlings and emblings which regenerated from somatic embryos were compared to the height, DBH, foliar characteristics, content of chlorophyll (chlorophyll a, b and total chlorophyll), carotenoid and leaf microstructure in Liriodendron tulipifera. In comparison of height and DBH (diameter at breast height), no significant differences were found in height (seedling, 3.8 m; embling, 3.87 m) and DBH (seedling, 12.09 cm; embling, 12.53 cm). The emblings and seedlings were similar in values of length (seedling, 108.11 mm, embling, 113.59 mm), width (seedling, 149.1 mm; embling, 167.71 mm), surface area (seedling, $119.92mm^2$; embling, $164.43mm^2$), fresh weight (seedling, 2.1 g; embling, 2.62 g) of leaf, and length (seedling, 81.49 mm; embling, 98.41 mm) and thickness (seedling, 1.66 mm; embling, 1.98 mm) of petiole. In case of chlorophyll content in the leaves, the chlorophyll a (seedlings, $11.2{\mu}g/g$; emblings, $13.2{\mu}g/g$), b (seedlings, $4.8{\mu}g/g$; emblings, $5.4{\mu}g/g$) and total content were higher in emblings ($930.2{\mu}g/g$) than seedlings ($800.1{\mu}g/g$), however, content of carotenoid (seedlings, $260.3{\mu}g/g$; embling, $265.2{\mu}g/g$) showed similar in both plants. Leaves of emblings had a similar pattern of histological structure (palisade or sponge parenchyma) to that of seedlings leaves. Therefore, the results showed that there were no remarkable growth differences when compared with 5-year-emblings and seedlings of yellow poplar.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.660-667
• /
• 2010

In this research polyimide, Matrimid 5218, hollow fiber membrane was used to recover sulfur hexafluoride($SF_6$) which is one of the six greenhouse gases from $N_2/SF_6$ mixture gas. Fibers were spun from using dry-wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a sponge-like substructure. The developed module had a permeance of 0.78-1.36 GPU for $N_2$ with $N_2/SF_6$ selectivity of 2.44-5.08 at various pressure and temperature. For recovery of $SF_6$, a membrane module and 10 vol.% $SF_6$ from $N_2/SF_6$ mixture gas was used. The effects of various operating condition such as pressure, temperature, and retentate side flow rate were tested. When pressure and temperature were increased and retentate flow rate was decreased, the $SF_6$ purity in recovered gas was increased up to 37.5 vol.% with decreasing recovery ratio. When retentate flow rate was increased pressure and temperature was decreased, the $SF_6$ recovery ratio in retentate side was increased up to 89% with decreasing the $SF_6$ purity in retentate side.

• Journal of Conservation Science
• /
• v.30 no.4
• /
• pp.335-343
• /
• 2014

This study classified the result of non-metallic inclusion analysis and result of microstructure investigation on the ironware excavated in the Baekje region into Han River, Geum River, and Yeongsan River to estimate the iron making temperature and study the characteristics of regional and temporal characteristics of the heat treatment technology and steel making technology. Regardless of era, bloom iron and sponge iron are judged to be the major method for making as a directreduction process in all three regions. The result of the reinterpretation of the non-metallic inclusion by the oxide ternary constitutional diagram suggest that the temperature inside of the furnace is estimated to be between $1,100{\sim}1,300^{\circ}C$ while making the steel. The magnetic iron ores are the major raw material of steel ore and irons with high $TiO_2$ are estimated to use iron sands. Ironware with $CaO/SiO_2$ rate higher than 0.4% are considered to have artificially added the flux of calcareous materials. It was found that the iron making method is the solid caburizing-steel which caburizes low-carbon steels by the CO gas and $CO_2$ gas created when heating the forging furnace with charcoal. Also, the ironware manufacturers in the Baekje during 3rd century recognized the heat treatment technology as they performed carburizing process and quenching to intentionally increase the strength of necessary parts.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.250-255
• /
• 2011

In this study, by using the polymeric membrane separation process, the $CO_{2}/CH_{4}$ separation and $H_{2}S$ removal from biogas were performed in order to $CH_{4}$ purification and enrichment for the fuel cell energy source application. Fibers were spun by dry/wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a porous, sponge substructure. The permeance of $CO_{2}$ and $CO_{2}/CH_{4}$ selectivity increased with pressure and temperature. Mixture gas with increasing pressure and temperature, removal efficiency of the $CO_{2}$ and $H_{2}S$ were decreased while concentration of $CH_{4}$ was increased up to 100%. When retentate flow rate was increased with the decreasing of pressure and temperature the $CH_{4}$ recovery ratio in retentate side was increased while the $CH_{4}$ purity in retentate side was decreased.

• Archives of Plastic Surgery
• /
• v.32 no.3
• /
• pp.335-342
• /
• 2005

This study was undertaken to investigate possibility of the allogenic type I collagen inducing osteoinduction or osteoconduction at critical sized bone defect in the rabbit. Twenty Newzealand white rabbit, weighted from 2.8 kg to 3.5 kg, were used in this study. The skull was exposed and two bony defects were created with diameter of 10 mm. Group I(n=10), the bony defects was grafted from the other side bone. Group II(n=10), the bony defects was grafted by the allogenic type I collagen with bone morphogenic protein(BMP). Group III(n=10), the bony defects was grafted by the allogenic type I collagen only. Group IV(n=10), the bony defects was lefted with no grafts. The grafted bones and allogenic type I collagen were investigated with radiologic densitometry, histologic analysis and immunohistochemistry after 12 weeks. No major difference was observed in the gross finding between Group I, II, III, but dura mater was exposed in bony defect,the Group IV. The radiologic study demonstrated more bony opacity in the Group I, but the other groups did not demonstrate a significant difference. In the histologic study, grafted bone edge was completely consolidated with original bone in group I and new bone ingrew into the grafted allogenic type I collagen(group II, III),but there is no bone regeneration from the original bony edge in the group IV. The percent of the new bone formation by cross-sectional area was considered statistically significant at a p value of less than 0.05(p<0.05). In the immunohistochemistry study about BMP antibodies, the group IV demonstrated osteogenic activity in front of advancing original bone edge, in which the osteoblast stained strongly for BMP antibodies, but other group does not demonstrated any osteoblastic expression. There was no immunologic rejection. In conclusion, this results do not demonstrate that the allogenic type I collagen is useful for bone substitute, but the characters of the collagen, such as pliability, easy-handling, sponge-like structure, are useful in interpositional bone graft substitutes. The further evaluation of long term results about the resorption, immunologic tissue reaction, response of applied tissue growth factor to the allogenic collagen is needed.

• Membrane Journal
• /
• v.18 no.1
• /
• pp.84-93
• /
• 2008

Poly(vinylidene fluoride) has received much attention in the last several years for the lithium secondary batteries. In this study, to enhance the porosity, PVdF was prepared by phase inversion method using as an additive, PEG (poly(ethylene glycol)), with N,N-dimethylformamid as a solvent. The pores are generated during the solvent and non-solvent exchange process in the coagulation bath filled with non-solvent (distilled water). The surface and cross-section of the membranes were observed with a scanning electron microscopy (SEM). The mechanical property of the membrane was determined by using an universal testing machine (UTM) and thermal property was verified by heat shrinkage. Uniformed sponge structure of PVdF-PEG membrane for the lithium secondary batteries was prepared with 10 wt% of PEG concentration in the PVdF-PEG solution. Porosity, elongation and tensile strengh of the membrane were 87%, 75.45%, and 275. 27 MPa respectively.