• Textile Coloration and Finishing
• /
• v.8 no.1
• /
• pp.1-7
• /
• 1996

In discharge printing of cotton fabrics dyed with C.I. Reactive Orange 16(O-16), C.I. Reactive Blue 19(B-19) and C.I. Reactive Black 5(Bl-5), when the dyes were discharged by some chemicals, such as $K_{2}CO_{3}$, BASB, DSR, sarcosine and GSB, the single use of those chemicals made a very poor discharge, but mixing them with $K_{2}CO_{3}$ resulted to the outstanding improvement of discharge. Especially the dischargeability of $K_{2}CO_{3}$ BASB or $K_{2}CO_{3}$+DSR was very gratifying. For O―16, $K_{2}CO_{3}$+ DSR was slightly more effective than $K_{2}$CO$_{3}$+BASB, but for B―19 and Bl―5 $K_{2}CO_{3}$+BASB and $K_{2}CO_{3}$+DSR showed similar good results. In discharging of O―16 and B―19 by $K_{2}CO_{3}$+BASB or $K_{2}CO_{3}$ +DSR, the dischargeabilities of them increased as the time of 102$^{\circ}C$ steaming increased under the condition of 102$^{\circ}C$ steaming and no baking, but not under the condition of 102$^{\circ}C$ steaming and 16$0^{\circ}C$ baking. However for Bl-5, without regard to baking, the 102$^{\circ}C$ steaming of more than 15 minutes caused the discharge to be much more remarkable than that of 8 minutes did. Generally baking elevated the dischargeability, and this was sure in discharging by $K_{2}CO_{3}$+BASB or $K_{2}CO_{3}$+DSR. And it was confirmed that the structure of vinylsulfonyl reactive dyes could effect on the dischargeability because the three dyes, though little, showed different discharge behaviors.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.4
• /
• pp.274-279
• /
• 2008

In the perspective of saving energy in buildings, high performance of insulation and air tightness for improving the heating and the cooling efficiency has brought the positive effect in an economical view. However, these building energy saving technologies cause the lack of ventilation, which is the direct cause of increasing the indoor contaminants, and it is also very harmful to residents because they spend over 90% of their time in the indoor area. Therefore, the ventilation is important to keep indoor environment clean and it can also save energy consumption. In this study, a HEPA type breathing wall is designed as a passive ventilation system to collect airborne particles and to supply fresh outdoor air. To make fine porous structures, polymer nano fibers which were made by electro spinning method are used as a precursor. The nano fibers are coated with SiO2 nano particles and finally the HEPA type breathing wall is made by sintering in the electric furnace at $300\sim500^{\circ}C$. The pressure drops of nano ceramic structure are 8.2, 25.5 and 44.9 mmAq at the face velocity of 2.0, 5.9 and 8.8 cm/s, respectively. Also the water vapor permeability is $3.6g/m^2{\cdot}h{\cdot}mmHg$. In this research, the porous nano ceramic structures are obtained and the possibility for the usage of a material for HEPA type breathing wall can be obtained.

• Composites Research
• /
• v.26 no.2
• /
• pp.123-128
• /
• 2013

The PVDF (polyvinylidene fluoride) fibers were prepared using the wet spinning processing. To improve ${\beta}$-phase crystalline which closely related piezoelectric property PVDF wet spun fibers conducted post treatment. Post treatment is consisted of heat stretching and annealing process. The heat stretching and annealing conditions were controlled by changing temperature between glass transition temperature and melting temperature. From these experimental data, the resulting crystal structure of the ${\beta}$-phase crystalline was confirmed by FT-IR and XRD experiments. From these analysis results, optimum stretching and annealing conditions of the wet spun PVDF fibers were founded to increase high ${\beta}$-phase crystalline. Furthermore results showed that thermal processing had a direct effect on modifying the crystalline microstructure and also confirmed that heat stretching and annealing could increase the degree of crystallinity and ${\beta}$-phase crystalline. Finally, piezoelectric constant ($d_{11}$) of the post heat treated PVDF fibers reinforced composite were measured to investigate the feasibility for the sensing materials.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.581-587
• /
• 2009

PLA/PEG blend fibers composed of poly (lactic acid) (PLA) and poly (ethylene glycol) (PEG) were prepared via melt blending and spinning for bioabsorbable filament sutures. The blend fibers hydrolyzed with the immersion in a phosphate buffer solution at pH 7.4 and $37\;^{\circ}C$ for 1~8 weeks. The effects of blending time, blend composition, and hydrolysis time on the weight loss and tensile strength of the hydrolyzed blend fibers were investigated. After hydrolysis, the weight loss of the blend fibers increased with increasing PEG content, blending time, and hydrolysis time. The tensile strength and tensile modulus of the blend fibers decreased with increasing PEG content, blending time, and hydrolysis time. Therefore, it can be concluded that the weight loss of the PLA/PEG blend fibers was less than 0.9% even at hydrolysis time of 2 weeks and their strength retentions were over 90%.

• Journal of Magnetics
• /
• v.10 no.3
• /
• pp.122-127
• /
• 2005

New classes of LC resonators for micro magnetic sensor device were proposed and fabricated. The first type LC resonator (Type I) consists of a small piece of microwire and two cylindrical electrodes at the end of the microwire without direct contact to its ferromagnetic core. In type I resonator the ferromagnetic core of the microwire and cylindrical electrodes act as an inductor and two capacitors respectively to form a LC circuit. The second type LC resonator (Type II) consists of a solenoidal micro-inductor with a bundle of soft magnetic microwires as a core. The solenoidal micro-inductors fabricated by MEMS technique were $500\sim1,000\;\mu{m}$ in length with $10\sim20$ turns. A capacitor is connected in parallel to the micro-inductor to form a LC circuit. A tiny glass coated $CO_{83.2}B_{3.3}Si_{5.9}Mn_{7.6}$ microwire was fabricated by a glass-coated melt spinning technique. A supergiant magneto-impedance effect was found in a type I resonator as much as 400,000% by precise tuning frequency at around 518.51 MHz. In type II resonator the changes of inductance as a function of external magnetic field in micro-inductors with properly annealed microwire cores were varied as much as 370%. The phase angle between current and voltage was also strongly dependent on the magnetic field. The drastic increments of magnetoimpedance at near the resonance frequency were observed in both types of LC resonators. Accordingly, the sudden change of the phase angle, as large as $180^{\circ}C$, evidenced the occurrence of the resonance at a given external magnetic field.

• Journal of the Korean Magnetic Resonance Society
• /
• v.25 no.2
• /
• pp.12-16
• /
• 2021

Daphnia magna is used as target organism for environmental metabolomics. The metabolome of D. magna was studied with NMR spectroscopy. Most studies used the extract of D. magna, but the reproducibility cannot be obtained using extracted sample. In this study, lyophilized D. magna samples were analyzed with two different ¹H NMR techniques, HR-MAS on intact tissues and solution NMR on extracted tissues. Samples were measured three times using 600 MHz NMR spectrometer. Metabolite extraction required more than twice as many D. magna, but the metabolite intensity was lower in solution NMR. In the spectra of HR-MAS NMR, the lipid signal was observed, but they did not interfere with metabolite profiling. We also confirmed the effect of swelling time on signal intensities of metabolites in HR-MAS NMR, and the results suggest that appropriate swelling should be used in lyophilized D. magna to improve the accuracy of metabolite profiles.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.401-406
• /
• 2023

With the development of industry, fine dust is causing difficulties in various fields such as environment, health, and life, and a large amount of pollutants generated from human social activities are emerging as a serious environmental problem due to air pollution. Therefore, in this study, activated carbon was added to remove fine dust and volatile organic compounds by spinning cellulose acetate polymer fibers on a silicon support using the electrospinning method. By varying the activated carbon ratio and electrospinning time, the fine dust blocking effect and toluene adsorption performance were confirmed according to the activated carbon ratio and filter thickness. As a result, it was shown that the particles were effectively blocked with the increase in the electrospinning time due to the filter thickness increase. Adsorbed amount of toluene was increased with increase in activated carbon amount. Light transmittance was decrease with increase in electrospinning time, showing that there were light transmittance in filters electrospun for 20~30 minutes.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.

• Clean Technology
• /
• v.21 no.3
• /
• pp.164-170
• /
• 2015

In this study, polysulfone-Escherichia coli biomass composite fiber (PSBF) was prepared by spinning the suspension of PS and E. coli biomass and amine-methylated PSBF (AM-PSBF) was fabricated through the methylation of amine groups in PSBF. As comparing the adsorption characteristics of basic dye, Basic Blue 3 (BB3) by the PSBF and AM-PSBF, the effect of the methylation of amine groups on BB3 adsorption was confirmed. pH edge experiments showed that the BB3 uptake of PSBF and AM-PSBF increased as pH was increased and the BB3 uptake of AM-PSBF was higher than that of PSBF at the same pH. Both of PSBF and AM-PSBF was reached at equilibrium within 5 h and kinetic experimental data were well fitted by the pseudo-first-order kinetic model. By the Langmuir model, the maximum adsorption capacities of PSBF and AM-PSBF at pH 8 were evaluated to be 28.9 and 20.7 mg/g, respectively. The maximum adsorption capacity of AM-PSBF was enhanced 1.4 times comparing that of PSBF. These results indicate that the methylation of amine groups in PSBF leads to the improvement of BB3 adsorption capacity. In addition, the results of desorption experiments revealed that AM-PSBF was repeatedly reusable.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.219-225
• /
• 2014

In this study, effect of cosurfactant on the solubilization rate of n-octane, n-decane and n-dodecane oil was performed by micellar solutions of polymeric nonionic surfactant Pluronic L64($EO_{13}PO_{30}EO_{13}$) at room temperature. It has been found that the solubilization rate of a hydrocarbon oil was enhanced with an increase in both chain length and amount of alcohol added. In case of addition of a short chain alcohol such as 1-butanol, the solubilization rate of a hydrocarbon oil was slightly increased since most of alcohol molecules remained in an aqueous surfactant solution. On the other hand, the addition of a relatively long chain alcohol such as 1-hexanol and 1-octanol produced a big increase in solubilization rate of a hydrocarbon oil mainly due to incorporation of alcohol molecules into micelles and thus producing more flexible micellar packing density. Dynamic interfacial tension measurements showed the same trend found in solubilization rate measurement. Both interfacial tension value at equilibrium and time required to reach equilibrium decreased with an increase in chain length of an alcohol.