• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.309-314
• /
• 2001

The balance of high speed spindle system with high precision rotation like grinding machine is very important. Traditionally, we use trial and error method to balance the spindle. It takes much time. So we are developing the automatic balancing equipment being used in the grinding machine. The balancing head we develop is wireless. It will be used high-speed grinding machine. We use influence coefficient method to control the automatic balancer. Experiments are based on automatic and manual balancing. We perform test of the vibration filter. It helps to remove noise. The filter and experiments with automatic balancing controller show that automatic balancing control can be successfully achieved with the quick response and good stability characteristics.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.393-398
• /
• 2004

This paper is focused on practical applicability of the optical fiber sensor considering the machine center which is going to use them. Optical fibers may be fluctuated because the machine center operates as column moving type. This causes distortion of the sensor output signal. To reduce this problem, we have improved the sensor structure and its bracket. And we evaluated performances of the sensor.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.466-470
• /
• 2000

Externally pressurized air journal bearing has been widely used in high-speed spindle system and precision machinery because of its characteristics such as substantially low frictional loss, low heat generation and averaging effect leading better running accuracy. But air journal bearing have a disadvantage of the low load capacity due to the low viscosity. In this paper, The air journal bearing design to overcome the defects of air bearing such as low stiffness and dimping coefficients was investigated theoretically.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.11-15
• /
• 2002

This paper presents the thermal characteristic analysis of a high-speed HMC with spindle speed of 50,000rpm. The spindle is supported by two radial and axial magnetic bearings. and the built-in motor is located between the axial and rear radial magnetic bearings. The X-axis and Y-axis feeding systems are composed of linear motor and linear motion guides, and the Z-axis feeding system is composed of servo-motor, ballscrew and linear motion guide. The thermal analysis model of high-speed HMC is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on the temperature distribution and thermal deformation under the conditions related to the heat generation of built-in motor, magnetic bearings, linear motors, servo-motor, ballscrew, and so on.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.598-604
• /
• 2003

In order to meet the growing demands for higher storage density as well as lower noise level, the spindles In hard disk drives are to be supported by hydrodynamic bearings in place of conventional ones. However, the existing models are inappropriate to apply to accurate Prediction or vibration characteristics because the Inn spindle tends to take quite a complex shape to secure the performance of the new type bearings. In this context, this paper treats analysis of free and forced vibrations of such-designed HDD spindles based on more sophisticated models and validation by means of experiments. Remarkably, to this end each component in the system is modeled as elastic adopting the finite element method.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.99-103
• /
• 2001

Though the research and the development in the field of machine tool was focused on high precision and high speed machine these days, traditional gear reduction device has been used to increase the cutting force which was transmitted from power source, motor In this study, analysis of 2 step gear reducer used in machining center spindle was carried out by using APM WinMachine which is commercial software for the analysis of machine element and system. For the analysis of this device, first of all, the analysis of power source and the transmitting of it were carried out. Then, machine elements like gear, shaft, bearing, and the forth, was analyzed in the view point of life time, static strength, stiffness, fatigue failure, etc. Consequently, we can estimate them and introduce new idea of the design modification of reduction device by this study.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.131-136
• /
• 2003

Five expensive sensors are necessary to control a magnetic bearing system. The sensor price rate of magnetic bearing system is high. So it is necessary that cheap and good sensor is developed. The optical fiber displacement sensor is adaptive to satisfy this condition. We can design magnetically suspended spindle based on static characteristic of optical fiber displacement sensor developed. The controller can be designed by decoupled feedback PD. Therefore, it is simpler than any other controller comparatively.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.377-382
• /
• 2005

This paper describes the design of micro machine tools system for mechanical machining of micro/meso scale mechanical parts. The micro machining systems such as $\mu-Late$, $\mu-milling/drilling$ machine and $\mu-grinding$ machine are the basic elements constructing $\mu-factory$ which gains more attention recently because of increasing needs of mico and nano-parts in various industrial and medical area. A miniaturized 3-axis milling machine with VCM stage and air spindle and palm-top size micro-late are designed, and air bearing stage and stepwise linear motion system with PZT are studied for motion system. The micro cutting characteristics are investigated experimentally, and reconfigurable machine structures are also considered.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.1
• /
• pp.104-111
• /
• 1995

The needs of ultraprecision machine tools, which manufacture and machine the high precision parts used in computers, semiconductors and othe rprecise machines, have been increased recentrly. So it is important to design the driving parts of the ultraprecision machine tools which affect significantly on the performance of them. In this paper, the dynamic analyses on the belt-drive system were studied. The correlational equations between the acoustic natural frequency and the tension of belt were derived by experiments. The dynamic delections while the dynamic loads on the motor system changed were analyzed by the finite element analysis. The nonlinear characteristics of the bearings on the dynamic performance was studied and the belt connecting the motor to the spindle of a machine tool was modeled by the truss element and the beam element.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.128-135
• /
• 2006

This paper presents a finite element method to analyze the free vibration of a flexible HDD composed of the spinning disk-spindle system with fluid dynamic bearings(FDBs), the head-suspension-actuator with pivot bearings, and the base plate with complicated geometry. Experimental modal testing shows that the proposed method well predicts tue vibration characteristics of a HDD. This research also shows that even the vibration motion of the spinning disk corresponding to half-speed whirl and the pure disk mode are transferred to a head-suspension-actuator and base plate through the air bearing and the pivot bearing consecutively. The proposed method can be effectively extended to investigate the forced vibration of a HDD and to design a robust HDD against shock.