• Journal of Ocean Engineering and Technology
• /
• v.25 no.2
• /
• pp.1-6
• /
• 2011

Vibration-based Structural Health Monitoring (SHM) systems use field measurements of operational signals, which are distorted by noise from many sources. Reducing this noise allows a more accurate assessment of the original "clean" signal and improves analysis results. The implementation of a noise reduction methodology for the Modal Distribution Method (MDM) is reported here. The spectral subtraction method is a popular broadband noise reduction technique used in speech signal processing. Its basic principle is to subtract the magnitude of the noise from the total noisy signal in the frequency domain. The underlying assumption of the method is that noise is additive and uncorrelated with the signal. In speech signal processing, noise can be measured when there is no signal. In the MDM, however, the magnitude of the noise profile can be estimated only from the magnitude of the Power Spectral Density (PSD) at higher frequencies than the frequency range of the true signal associated with structural vibrations under the additional assumption of white noise. The implementation of the spectral subtraction method to MDM may decrease the energy of the individual mode. In this work, a modification of the spectral subtraction method is introduced that enables the conservation of the energies of individual modes. The main difference is that any (negative) bars with a height below zero after subtraction are set to the absolute value of their height. Both noise reduction methods are implemented in the MDM, and an application example is presented that demonstrates its effectiveness when used with a signal corrupted by noise.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.293-294
• /
• 2009

The spectral responsivity of solar cells has been measured under high background irradiance using an LED-based differential spectral responsivity Comparator (DSR-C). The comparator developed is fully automated and has some advantages: It does not need a chopper to modulate the light. Unlike the conventional method, it does not require a monochromator to select wavelength. It covers a wavelength range up to 1200 nm. The wavelength range of the comparator is limited by the spectral power distribution of the LEDs and the spectral responsivity of the standard detector. An active temperature control was utilized to meet the specified standard conditions of solar cell test. This work shows the effect of different levels of background irradiance on the spectral responsivity and the importance of same background irradiance for solar cell test as specified by the corresponding standard.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.168-173
• /
• 2011

Recently, from a saving energy and environmental lighting sources point of view, using LED lighting have been increased rapidly. The colors of light was applied to the control of dimmers that is composed of red, green, blue, and white(RGBW) to improve the quality of visual environment. Moreover this study has been processed to develop adjustable dynamic LED lighting system on SPD and definitize the various spectral power distribution and color temperature of light through the control of the four dimmers. It is possible to combine up to $432^4$ kinds of light. Measurement of illuminance of range on working surface was as 7~l,831 lux. Application of visual environment for occupants can be expected according to control of lighting performance.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.11
• /
• pp.609-615
• /
• 2000

A prototype electrodeless sulfur lamp was developed and investigated the spectroscopic characteristics. The emission spectra of $S_2$ in the microwave-discharged eletrodeless sulfur lamp (ESL) were studied at various input power. The emission spectra of the ESL shift to longer wavelength with increasing of the input power. We have shown that this is due to the self reversal effect in the high pressure gas discharge. We also show that the self reversal effect increases as the rotation of the discharged bulb. The spectral distribution of the ESL shifts about 45 nm toward visible region from UV region due to the rotation of the lamp bulb.

• Structural Engineering and Mechanics
• /
• v.86 no.2
• /
• pp.237-247
• /
• 2023

Fourier series-based models in the time domain are frequently established to represent individual bouncing loads, which neglects the stochastic property of human bouncing activity. A power spectral density (PSD) model in the frequency domain for individual bouncing loads is developed herein. An experiment was conducted on individual bouncing loads, resulting in 957 records linked to form long samples to achieve a fine frequency resolution. The Welch method was applied to the linked samples to obtain the experimental PSD, which was normalized by the bouncing frequency and the harmonic order. The energy, energy distribution center, and energy distribution shape of the experimental PSD were investigated to establish the PSD model. The proposed model was used to analyze structural vibration responses using stochastic vibration theory, which was verified via field measurements. It is believed that this framework can evaluate the vibration capacity of structures excited by bouncing crowds, such as concert halls and grandstands.

• Journal of Biomedical Engineering Research
• /
• v.6 no.1
• /
• pp.19-30
• /
• 1985

This paper describes the EMG signals in frequency domain using power spectral density, The changes in the moan frequency can represent the energy distribution which results from changing in load before and during fatigue. Most of EMG signal power spectrum is located between 10 and 200Hz. Shifts of the high-energy regions of the power spectra can be inferred from the changes in the mean frequency. If the load is increased without fatigue-ocurring, the high frequency regions have more energy than the low frequency regions. And if load is increased during fatigue, the low frequency regions have more energy than the high frequency regions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.2
• /
• pp.75-82
• /
• 1994

The existence of peroodic impulse noises in distribution line carrier (DLC) communication system is known to be the most serious obstacle for improving DLC communication quality in reliability and capacity. From the spectral points, impulse noises can be divided into baseband type and modulation type the noise width of whichs are much different each other. With each nose type, this study presents the basic characteristics in relation to what they originate from and how their spectrum properties are revealed. The baseband type impulse noise is normally caused from thyristor circuit running with low switching speed and the modulation type noise from the circuit of switching power supply. The base wave of modulation noise is shown to be the pulsuatic charging current to primary condenser in switching power circuit. The study result indicates also that placing the DLC carrier frequency away the band predominated by modulated noise especially from RCC type switching power circuit is very important in DLC design.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.4
• /
• pp.392-400
• /
• 2001

This paper proposes an illuminant estimation algorithm that estimates the spectral power distribution of an incident light source from a single image. The proposed illumination recovery procedure has two phases. First, the surface spectral reflectances are recovered in the maximum achromatic region (MAR) which is the most achromatic and highly bright region of an image after removing partially the effect of illumination using a modified gray world algorithm. Here, the surface reflectances of MAR are estimated using the principal component analysis method along with a set of given 1269 Munsell samples. Second, the Population of reflected lights is determined with 1269 Munsell samples and a set of illuminations then the spectral distribution of re(looted lights of MAR is selected from the spectral database. That is, color differences are compared between the reflected lights of the MAR and the spectral database, which is the set of reflected lights built by the given set of Munsell samples and illuminants. Then the closest colors from the spectral database are selected. Finally, the illuminant of an image can be calculated dividing the average spectral distributions of reflected lights of MAR by the average surface reflectances of the MAR. In order to evaluate the proposed algorithm, experiments with artificial scenes, which are exposed to chromatic illuminants, were performed and the spectral distribution of estimated illumination and color difference are compared with results of the conventional method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.6
• /
• pp.744-750
• /
• 2020

In this paper, we propose a deep learning based transmit power control (TPC) scheme to improve the spectral and energy efficiency of wireless communication systems. In the wireless communication system, the positions of multiple transceivers follow a uniform distribution, and the performances of spectral and energy efficiency for the proposed TPC scheme are analyzed assuming the Nakagami fading channels. The proposed TPC scheme uses batch normalization to improve spectral and energy efficiency in deep learning based training. Through simulation, we compare the results of the spectral and energy efficiency of the proposed TPC scheme and the conventional one for various area sizes that limit the position range of the transceivers and Nakagami fading factors. Comparing the performance results, we verify that the proposed scheme provides better performance than the conventional one.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.11
• /
• pp.5218-5233
• /
• 2018

The coexisting wireless body area networks (WBAN) is a very challenging issue because of strong inter-networks interference, which seriously affects energy consumption and spectrum utilization ratio. In this paper, we study a power control strategy with nearest neighbor nodes distribution for coexisting WBAN based on stochastic geometry. Using homogeneous Poisson point processes (PPP) model, the relationship between the transmission power and the networks distribution is analytically derived to reduce interference to other devices. The goal of this paper is to increase the transmission success probability and throughput through power control strategy. In addition, we evaluate the area spectral efficiency simultaneously active WBAN in the same channel. Finally, extensive simulations are conducted to evaluate the power control algorithm.