• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.1
• /
• pp.24-31
• /
• 2003

In the gas cutting of plate steel, the quality of the cut surfaces and sections is strongly dependent on the cutting conditions such as cutting speed, kerf width, plate thickness, material, distance between tip and specimen, and cutting oxygen pressure etc. The cutting tests of plate steel were carried out using CNC gas cutting machine. This paper deals with cut surface and section characteristics of plate steel in CNC gas cutting. Both top and bottom widths of kerf, the surface roughness(Ra, Rmax) of cutting surfaces are measured under various cutting conditions such as cutting speed, material, distance between tip and specimen, and cutting thickness. The photographs of cut surface and cut section are also analyzed under various cutting conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.154-161
• /
• 2003

The effects of specimen geometry, and loading conditions on the J-integral fur CCT (center cracked tension) specimens are investigated by using FEM. It is found that the J-integral tends to decrease according to the parallel tensile loading to crack line. Furthermore, it is verified that the compressive parallel loading to crack line is likely to increase the J-integral. A stress ratio of length to width of the center CCT specimen is confirmed to affect the J-integral significantly.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.10
• /
• pp.1636-1643
• /
• 2003

In this study, bolted joint made of Glass-Mat Reinforced Thermoplastics (GMT) specimen was under tensile loading to investigate the relation between joint strength and glass-fiber weight fraction of the flat plate specimen. The effect of molding conditions such as the initial size of a GMT charge and molding temperatures was investigated under plane strain condition. In consideration of the specimen geometry, minimum end distance and width of the specimen to induce the bearing fracture mode of the bolted joint were determined. And finally, the effect of the outer diameter of washer and clamping pressure on joint strength was also investigated. Since joint strength is dependent on the local glass-fiber weight fraction, experimentally measured strength was modified, considering its irregular values of the specimen molded under various processing conditions in order to obtain a reasonable correlation between the two.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.643-648
• /
• 2002

In the cutting of plate steel, the quality of the cut surfaces is strongly dependent on the cutting conditions such as cutting speed, kerf width, plate thickness, length of tip-specimen and oxygen pressure etc. the cutting tests of plate steel were carried out using CNC gas cutting machine. this paper deals with cutting characteristics of plate steel using CNC cutting machine. the width of cutting entrance and exit, the surface roughness of cutting surfaces and the cutting surface are examined at various cutting conditions.

• Journal of Conservation Science
• /
• v.37 no.6
• /
• pp.689-700
• /
• 2021

This study aims to optimize the measurement conditions of handmade Hanji paper to reduce the time required for measurement while meeting folding endurance standards, for various basis weights. Thirteen types were selected, including 12 types of Hanji with grammages of 17 g/m², 30 g/m², and 45 g/m², and one type of 75 g/m² copy paper, and 24 sheets were prepared in the laid and chain directions. Subsequently, folding endurance experiments at different load (14.72 N, 9.81 N, 4.91 N) and specimen width conditions (15 mm, 10 mm, 5 mm) were performed, using a 4-MIT folding endurance tester. The results showed that, for specimen widths of 15 mm and 10 mm under a load of 4.91 N, the folding endurance falls within the reference range (10~10000 times). In particular, reduced folding endurance range and measurement time were observed at a width of 10 mm under a load of 4.91 N. Moreover, the endurance trend lines based on the average values of load and specimen width ranges enabled the prediction of the folding endurance within those ranges, according to the decreasing slope. Furthermore, for a specimen width of 15 mm under a load of 4.91 N, the folding endurance in the comparison group (35 to 17723 times) significantly exceeds the upper limit of the reference range (10~10000 times). Therefore, the measurement conditions of 4.91 N with a specimen width of 10 mm are proposed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.149-154
• /
• 2003

The cutting tests of high tensile steel plate(AH36) were carried out using CNC plasma arc cutting machine. Both top and bottom width of kerf and the surface roughness(Ra, Rmax) of cut surface are measured under various cutting conditions such as cutting speed, steel plate thickness, etc. In the CNC plasma arc cutting, the surface roughness decreases as cutting speed increases. The hardness is high up to 4mm depth from the cutting surface. In the cutting speed 1300~2100mm/min, the ratio of proper kerf width(Wt/Wb) is around 2.6. Through the series the series of experiments, the satisfactory cutting conditions of high tensile steel plate were found.

• Geomechanics and Engineering
• /
• v.14 no.2
• /
• pp.131-139
• /
• 2018

The preparation of repeatable and uniformly reconstituted soil specimens up to the specified conditions is an essential requirement for the laboratory tests. In this study for large samples replication, the simultaneous usage of the traveling pluviation and curtain raining technique is used to develop a new method, called the curtain travelling pluviator (CTP). This simple and cost effective system is based on the air pluviation approach, whilst reducing the sample production time, can reproduce uniform samples with relative densities ranging from 25% to 96%. In order to investigate the resulting suitability and uniformity from the proposed method, a series of tests is performed. The effect of curtain traveling velocity, curtain width, drop height, and flow rate on the parameters of the sample is thoroughly investigated. Increase in the curtain velocity and drop height leads to the increase in relative density for the sand specimen. Increase in curtain width typically resulted in the reduction of relative density. Test results reveal that the terminal drop height for the sand specimen in this study is more than 500 mm. Relative density contour lines are presented that can be utilized in optimizing the drop height and curtain width parameters. Sample uniformity in the vertical and horizontal orientation is investigated through the sampling containers. Increasing relative density tends to result in the higher sample repeatability and uniformity.

• Structural Engineering and Mechanics
• /
• v.77 no.1
• /
• pp.89-102
• /
• 2021

Rapid construction of prefabricated bridges requires minimizing the field work of precast members and ensuring structural stability and constructability. In this study, we conducted experimental and analytical investigations of transverse joints of prefabricated T-girder bridge superstructures to verify the flexural performance and serviceability. In addition, we conducted parametric studies to identify the joint parameters. The results showed that both the segmented and continuous specimens satisfied the ultimate flexural strength criterion, and the segmented specimen exhibited unified behavior, with the flexural strength corresponding to that of the continuous specimen. The segmented specimens exhibited elastic behavior under service load conditions, and the maximum crack width satisfied the acceptance criteria. The reliability of the finite element model of the joint was verified, and parametric analysis of the convexity of the joint section and the compressive strength of the filler concrete showed that the minimum deflection and crack width occurred at a specific angle. As the strength of the filler concrete increased, the deflection and crack width decreased. However, we confirmed that the reduction in the crack width was hardly observed above a specific strength. Therefore, a design suitable for prefabricated bridges and accelerated construction can be achieved by improving the joint specifications based on the required criteria.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.186-191
• /
• 2002

In the CNC gas cutting of steel plate, the cutting quality are strongly dependent on the various cutting conditions. The cutting tests of high tensile steel plate(AH36) were carried out using CNC gas cutting machine at various cutting conditions such as cutting speed, steel plate thickness, distance between tip and specimen etc. The kerf width and the surface roughness of cutting surfaces are examined. The photographs of cutting surface and cutting section are also analyzed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.306-311
• /
• 1996

This paper persents the flexural behavior of high performance concrete beams having different concrete filling conditions. Three tests were conducted on full-scale beam specimens with design concrete compressive strength of 400 kg/$\textrm{cm}^2$. Different concrete filling conditions were intentionally made such that the first beam specimen was soundly cast to obtain the perfect concrete filling condition. Second beam specimen was cast in such a way that up to the longitudinal tensile reinforcement from the top, good concrete was filled while poor concrete was poured for the bottom part to simulate the poor workamanship, workability and unsatisfactory compaction. Third beam specimens was cast in such a way that up to the neutral axis of the beam section from the top, good concrete was filled while so did for the bottom part as the second beam specimen. The test results were analyzed in terms of load-displacement response, formation of crack, crack width, crack spacing and shift of neutral axis. An evaluation of the ductile response fo three different beam specimens was made in combination with the ultimate load accoding to the three different concrete filling conditions.