• 한국세라믹학회지
• /
• 제29권1호
• /
• pp.35-40
• /
• 1992

Porous glass in the ZrO2-SiO2 system containing up to 30 mol% zirconia were prepared from the mixed solutions of Zr(O.nC3H7)4 and partially prehydrolyzed TEOS by the sol-gel method. Pore characteristics, physical properties and alkali resistance were investigated. The gels converted into the porous glass by heating at $700^{\circ}C$, it was found that the glass like skeleton was already made up in lower temperature regions. The specific surface area of the porous glass was 227 $m^2$/g, average mean pore size was about 19$\AA$ and porosity was 19.2%, pore characteristics and physical properties depended on heating temperature. Alkali resistance of the porous glass increased as the zirconia content increased, because of the appearance of Zr-enriched layer at glass surface.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2008년도 하계학술발표회 논문집
• /
• pp.247-248
• /
• 2008

We investigated the influence of uniparabolic graded distributed Bragg reflector (DBR) using digital alloy on vertical series resistance and reflectivity of DBRs. Measured specific DBR series resistance was reduced to about 8.787${\times}$$10^{-6}$${\ohm}$ $cm^2$/period for digital alloy uniparabolic graded DBR. This was better than various graded DBRs, especially biparabolic graded DBR. Reflectivity of 42 pair uniparabolic graded DBR was found to be comparable to that of biparabolic graded DBRs.

• 대한임상검사과학회지
• /
• 제46권2호
• /
• pp.64-67
• /
• 2014

Vancomycin-resistant Enterococci (VRE) are a leading cause of a nosocomial infection. While seven glycopeptide resistance genotypes have been found in Enterococci, vanA and vanB are the most common resistance genotypes. Aims of this study were to detect antibiotic susceptibilities of 23 Enterococcus spp, which broke out in a university hospital by the disk diffusion test, to investigate specific genes of vanA and vanB by conventional and real-time PCR. PCR for vanA and vanB was performed on 23 Enterococci, all 23 were positive for vanA type. This study reports the validation of a simple and rapid VRE detection method that can be easily incorporated into the daily routine of a clinical laboratory. Early detection of VRE strains, including those with susceptibility to Vancomycin, is of paramount clinical importance, as it allows a rapid initiation of strict infection control practices as well as a therapeutic guidance for a confirmed infection. The real-time PCR method is a rapid technique to detect vanA in Enterococci. It is simple and reliable for the rapid characterization of VRE.

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.96-104
• /
• 1997

The present study was aimed to correlate the microstructure and the hardness as well as the wear resistance of the metal-ceramic particulated composite layer on the pure Al plate. The composite layers were constructed by the addition of TiC particles on the surface of Al-Cu alloyed layers by PTA overlaying process. Initially, the Al-Cu alloyed layers were achieved by the deposition of Al-(25 ~ 48%) Cu alloys on the pure Al plate by TIG process. It was revealed that TiC particles were uniformly dispersed without any reaction with matrix in the composite layer. The volume fraction of TiC particles (TiC V F) increased from 12% to 55% with increasing the number of pass of composite layer. Hardnesses of (Al-48%Cu + TiC (3&4layers)) composite layer were Hv450 and Hv560, respectively, due to the increase of TiC V/F. Hardnesses of (Al-Cu + TiC) composite layers decreased gradually with insreasing temperature from 100$^{\circ}$C to 400$^{\circ}$C, and hardnesses at 400$^{\circ}$C were then reached to 1/5 - 1/10 of room temperature hardness depending on the construction of composite layers. The Specific wear of (Al + Tic) layer and Al-48%Cu alloyed layer decreased to 1/10 of the of pure Al, while the specific wear of (Al-48%Cu + TiC (4 layers)) composite layer exhibited 1/15 of that of steel such as SS400 and STS304.

• 식물병연구
• /
• 제12권2호
• /
• pp.75-80
• /
• 2006

2003 년부터 2005 년까지 장미 주요 재배단지를 중심으로 뿌리혹병 발생을 조사한 결과 전지역에서 발생이 확인되었으며, 주로 토양재배보다는 양액재배되는 장미에서 발생이 더 심하였다. 뿌리혹병에 감염된 장미는 주로 지제부에 발생이 많았으며, 뿌리에 발생하여 생육이 부진해지는 피해를 나타내었다. 저항성 품종 선발에서는 '리틀 실버' 등 10 품종만이 저항성 품종으로 검정되었을 뿐 대부분이 감수성이었다. 특히 '골든게이트', '리틀마블', '로사로제티' 등은 매우 감수성이 높았다.

• Current Applied Physics
• /
• 제18권12호
• /
• pp.1496-1506
• /
• 2018

Organic/inorganic ultraviolet photodetector was fabricated using thermal evaporation technique. Organic/inorganic heterojunction based on thermally evaporated copper (II) acetylacetonate thin film of thickness 200 nm deposited on an n-type silicon substrate is introduced. I-V characteristics of the fabricated heterojunction were investigated under UV illumination of intensity $65mW/cm^2$. The diode parameters such as ideality factor, n, barrier height, ${\Phi}_B$, and reverse saturation current, $I_s$, were determined using thermionic emission theory. The series resistance of the fabricated diode was determined using modified Nord's method. The estimated values of series resistance and barrier height of the diode were about $0.33K{\Omega}$ and 0.72 eV, respectively. The fabricated photodetector exhibited a responsivity and specific detectivity about 9 mA/W and $4.6{\times}10^9$ Jones, respectively. The response behavior of the fabricated photodetector was analyzed through ON-OFF switching behavior. The estimated values of rise and fall time of the present architecture under UV illumination were about 199 ms and 154 ms, respectively. Finally, enhancing the photoresponsivity of the fabricated photodetector, post-deposition plasma treatment process was employed. A remarkable modification of the device performance was noticed as a result of plasma treatment. These modifications are representative in a decrease of series resistance and an increase of photoresponsivity and specific detectivity. The process of plasma treatment achieved an increment of external quantum efficiency from 5.53% to 8.34% at -3.5 V under UV illumination.

• International Journal of Oncology
• /
• 제56권6호
• /
• pp.1540-1550
• /
• 2020

The epidermal growth factor receptor (EGFR)-tyrosine kinase inhibitor (TKI), gefitinib, is an effective therapeutic drug used in the treatment of non-small cell lung cancers (NSCLCs) harboring EGFR mutations. However, acquired resistance significantly limits the efficacy of EGFR-TKIs and consequently, the current chemotherapeutic strategies for NSCLCs. It is, therefore, necessary to overcome this resistance. In the present study, the anticancer potential of natural extracts of Coptis chinensis (ECC) against gefitinib-resistant (GR) NSCLC cells were investigated in vitro and in vivo. ECC inhibited the viability, migration and invasion, and effectively induced the apoptosis of GR cells. These effects were associated with the suppression of EGFR/AKT signaling and the expression of anti-apoptotic proteins, Mcl-1 and Bcl-2, which were overexpressed in GR NSCLC cells. Combination treatment with ECC and gefitinib enhanced the sensitivity of GR cells to gefitinib in vitro, but not in vivo. However, ECC increased the survival of individual zebrafish without affecting the anticancer effect to cancer cells in vivo, which indicated a specific cytotoxic effect of ECC on cancer cells, but not on normal cells; this is an important property for the development of novel anticancer drugs. On the whole, the findings of the present study indicate the potential of ECC for use in the treatment of NSCLC, particularly in combination with EGFR-TKI therapy, in EGFR-TKI-resistant cancers.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.302-307
• /
• 2002

In end milling process, the undeformed chip section area and cutting forces vary periodically with phase change of the tool. However, the real undeformed chip section area deviates from the geometrically ideal one owing to cutter runout and tool shape error. In this study, a method of estimating the real undeformed chip section area which reflects cutter runout and tool shape error was presented during up-end milling of Inconel 718 using measured cutting forces. The specific cutting resistance, K. and $K_t$ are defined as the radial and tangential cutting forces divided by the modified chip section area. Both of $K_r$, and $K_t$ values become smaller as the helix angle increases from $30^\circ$ to $40^\circ$ Whereas they become larder as the helix angle increases from $40^\circ$ to $50^\circ$. On the other hand, the $K_r$, and $K_t$ values show a tendency to decrease with increase of the modified chip section area and this tendency becomes distinct with smaller helix angle.

• 한국정밀공학회지
• /
• 제19권8호
• /
• pp.63-70
• /
• 2002

In end milling process, the undeformed chip section area and cutting forces vary periodically with phase change of the tool. However the real undeformed chip section area deviates from the geometrically ideal one owing to cutter runout and tool shape error. In this study, a method of estimating the real undeformed chip section area which reflects cutter runout and tool shape error was presented in up end milling process using measured cutting forces. The average specific cutting resistance, Ka is defined as the main cutting force component divided by the modified chip section area. Ka value becomes smaller as the helix angle increases from $30^circC \;to\;40\circC$. But it becomes larger as the helix angle increases from $40^\circ$to 50 . On one hand, the Ka value shows a tendency to decrease with increase of the modified chip section area and this tendency becomes distinct with smaller helix angle.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.834-837
• /
• 2003

In this study, Ohmic contacts make on 3C-SiC using TiN. Ohmic contact resistivity of TiN/3C-SiC was evaluated. Specific contact resistance was calculated by Circular-TLM(transmission line model) method and physics properties were measured using XRD, SEM, respectively. TiN contact is stable at high temperatures and a good diffusion barrier material. The TiN/3C-SiC contacts are thermally stable to annealing temperatures up to $1000^{\circ}C$. The TiN thin-film depostied on 3C-SiC substraes have good electrical properties. Therefore, the TiN/3C-SiC contact can be usefully applied for high-temperature MEMS applications over $500^{\circ}C$.