• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.165-173
• /
• 2019

Lithium anodes (13, 15, 17, and 20 wt% Li) were fabricated by mixing molten lithium and iron powder, which was used as a binder to hold the molten lithium, at about $500^{\circ}C$ (discharge temp.). In this study, the effect of applied pressure and lithium content on the discharge properties of a thermal battery's single cell was investigated. A single cell using a Li anode with a lithium content of less than 15 wt% presented reliable performance without any abrupt voltage drop resulting from molten lithium leakage under an applied pressure of less than $6kgf/cm^2$. Furthermore, it was confirmed that even when the solid electrolyte is thinner, the Li anode of the single cell normally discharges well without a deterioration in performance. The Li anode of the single cell presented a significantly improved open-circuit voltage of 2.06 V, compared to that of a Li-Si anode (1.93 V). The cut-off voltage and specific capacity were 1.83 V and $1,380As\;g^{-1}$ (Li anode), and 1.72 V and $1,364As\;g^{-1}$ (Li-Si anode). Additionally, the Li anode exhibited a stable and flat discharge curve until 1.83 V because of the absence of phase change phenomena of Li metal and a subsequent rapid voltage drop below 1.83 V due to the complete depletion of Li at the end state of discharge. On the other hand, the voltage of the Li-Si anode cell decreased in steps, $1.93V{\rightarrow}1.72V(Li_{13}Si_4{\rightarrow}Li_7Si_3){\rightarrow}1.65V(Li_7Si_3{\rightarrow}Li_{12}Si_7)$, according to the Li-Si phase changes during the discharge reaction. The energy density of the Li anode cell was $807.1Wh\;l^{-1}$, which was about 50% higher than that of the Li-Si cell ($522.2Wh\;l^{-1}$).

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.3
• /
• pp.201-207
• /
• 2019

In this study, the direct tensile properties of amorphous metallic fiber-reinforced cement based composites according to the strain was evaluated. A thin plate-shape amorphous metallic fiber with 15mm and 30mm in length was used. And fiber-reinforced cement based composites were prepared with contents of 1.0, 1.5, 2.0%. The direct tensile test was conducted under the conditions of $10^{-6}/s(static)$ and $10^1/s(dynamic)$ strain rate. As a results, amorphous metallic fiber with a length of 15mm was observed in pull-out behavior from the cement matrix because of the short fiber length and large portion of mixed fiber. On the other hand, amorphous metallic fiber with a length of 30mm were not pulled out from matrix because the bonding force between the fiber and matrix was large due to rough surface and large specific surface area. However, fracture occurred because thin plate shape fibers were vulnerable to shear force. Tensile strength, strain capacity and toughness were improved due to the increase in the fiber length. The dynamic increase factor of L15 was larger that of L30 because the bonding performance of the fiber-matrix interface is significantly affected by the strain rate.

• Clean Technology
• /
• v.26 no.4
• /
• pp.263-269
• /
• 2020

Zeolite was synthesized hydrothermally using the water-treatment sludge, and the effects of various synthesis parameters like reaction temperature, reaction time, and Na2O/SiO2 molar ratio on the crystallization of zeolite were investigated. Crystal structure, physical property, and thermal stability of zeolite crystals were characterized by X-ray powder diffraction, FTIR spectroscopy, BET nitrogen adsorption, and TGA measurements. The removal efficiencies of nitrogen in ammonia, heavy metal ions, and TOC were calculated to evaluate zeolite's adsorption capacity. The primary chemical composition of water-treatment sludge was 28.79% Al2O3 and 27.06% SiO2. The zeolites were synthesized by merely employing the water-treatment sludge as silica and alumina sources without additional chemicals. Zeolite crystals synthesized through the water-treatment sludge were confirmed as an A-type zeolite structure. Zeolite A had the highest crystallinity obtained from a gel with the molar composition 2.1Na2O-Al2O3-1.6SiO2-65H2O after 5 h at a temperature of 90 ℃. The specific surface area of zeolite obtained was 55 ㎡ g-1, which was higher than commercial zeolite A. The removal efficiency of nitrogen in ammonia was 68% after 3 h of reaction time, while the removal efficiencies of Pb2+ and Cd2+ ions were 99.1% and 99.3%, respectively. These results indicate active ion exchange between Pb2+ or Cd2+ ion and Na+ ion in the zeolite framework. The adsorption experiments on the different zeolite addition conditions were performed for 3 h with 300 ppm humic acid. Based on the results, TOC's highest efficiency was 83% when 5 g of zeolite was added.

• Microbiology and Biotechnology Letters
• /
• v.48 no.4
• /
• pp.547-555
• /
• 2020

Microalgae are a promising resource in energy and food production as they are cost-effective for biomass production and accumulate valuable biological resources. In this study, CO2 assimilation, biomass, and lipid production of 4 microalgal species (Chlorella vulgaris, Mychonastes homosphaera, Coelastrella sp., and Coelastrella vacuolata) were characterized at different CO2 concentrations ranging from 1% to 9%. Microscopic observation indicated that C. vulgaris was the smallest, followed by M. homosphaera, C. vacuolata, and Coelastrella sp. in order of size. C. vulgaris grew and consumed CO2 more rapidly than any other species. C. vulgaris exhibited a linear increase in CO2 assimilation (up to 9.62 mmol·day-1·l-1) as initial biomass increased, while the others did not (up to about 3 mmol·day-1·l-1). C. vulgaris, Coelastrella sp., and C. vacuolata showed a linear increase in the specific CO2 assimilation rate with CO2 concentration, whereas M. homosphaera did not. Moreover, C. vulgaris had a greater CO2 assimilation rate compared to those of the other species (14.6 vs. ≤ 11.9 mmol·day-1·l-1). Nile-red lipid analysis showed that lipid production per volume increased linearly with CO2 concentration in all species. However, C. vulgaris increased lipid production to 18 mg·l-1, compared to the 12 mg·l-1 produced by the other species. Thus, C. vulgaris exhibited higher biomass and lipid production rates with greater CO2 assimilation capacity than any other species.

• Journal of the Korea Convergence Society
• /
• v.12 no.8
• /
• pp.131-144
• /
• 2021

In recent years, China has gradually made clear its decision to modernize the governance system and governance capacity of the government by the virtue of digital transformation. As for the smart prison, as a penal institution of the state, technological reform is a key element in the sustainable development of smart prisons; however, relying on technology does not necessarily lead to a better service experience. Service design concept, as a coordinator of technology and social sustainability, needs to be adapted to the technological integration of smart prisons and to the needs for service design in the prison context in a new mode of thinking about services. This paper takes the development of the Jail Pay financial services system, one of the twelve sub-systems of the Smart Prison, as an entry point to explore the characteristics and shortcomings of the service design approach in achieving sustainable service innovation in the Smart Prison, it proposes an experience-based lead collaborative design (EBLCD) that is suitable for the specific needs in the prison context. The EBLCD is a theoretical framework and practical experience for sustainable service innovation in the construction of smart prisons.

• Journal of Korea Water Resources Association
• /
• v.55 no.7
• /
• pp.531-543
• /
• 2022

Integrated water resources management (IWRM) has focused on efficient response to various water related disasters by climate change. In particular, more flexible usage of conventional water resources infrastructures is expected to provide an eco-friendly water management. Multi-purpose dams and water supply dams are well known as water management facilities for securing and supplying water in drought season. Recently, based on the report '2021 multi-purpose use of hydropower dams in Han river', contribution of hydropower dams on water resources management is becoming more significant beyond the traditional role of hydropower generation. In drought conditions, the dams control water supply depending on the pre-defined drought stages. In the case of multi-purpose dams, an operation standard during drought has been already prepared and applied; however, for the hydropower dams, specific standards are not fully prepared yet in South Korea. In this study, a method for calculation of standard water storage and discharge reduction of hydropower dams according to drought stage is newly proposed reflecting the characteristics of hydropower dams. The proposed method was applied to the hydropower dams in Han river, where six hydropower dams are located. A case study of the historical droughts occurred in 2014-2017 demonstrated that the proposed hydropower dam operation rule could improve the water supply stability under severe drought conditions compared to the conventional operations. In the future, the role of hydropower dams for water resources management is expected to become more important, and this study can be widely used for water supply planning such as drought response using hydropower dams.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.624-629
• /
• 2022

Formaldehyde is an indoor pollutant that is harmful to humans, such as causing respiratory and skin diseases. Nitrogen plasma treatment was performed to introduce nitrogen groups on the surface of the activated carbon fibers (ACFs), and the adsorption characteristics of formaldehyde for the surface-modified ACFs were considered. As the nitrogen gas flow rate increased, the content of nitrogen functional groups introduced to the surface of the ACFs increased by about 7%, and the ratio of nitrogen functional groups to each type present was similar. Ultramicropores increased on the ACFs surface due to the etching effect of plasma treatment. The adsorption efficiency of formaldehyde on the modified ACFs surface was also enhanced. However, under the nitrogen flow rate of 120 sccm or more, the surface of the ACFs was excessively etched, and the specific surface area and the formaldehyde adsorption capacity decreased. Therefore, the content of the nitrogen groups is the main factor in the adsorption of formaldehyde on the nitrogen plasma-treated ACFs, but it can be found that the adsorption efficiency of formaldehyde is improved when the ACFs have a suitable pore structure.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.4
• /
• pp.491-501
• /
• 2021

Purpose: This study is designed to provide care workers with basic data on the development of job training programs for enhancing professionalism of senior care services by identifying and analyzing job recognition and education requirements according to the type of work place. Methods: Data were collected from April to July 2019 from 177 care workers working at the Elderly Care Facilities, Elderly Housing Welfare Facilities and Rehabilitation Facilities in the B Metropolitan City. It was analyzed using the SPSS Win 21.0 Statistical Program. Results: The results of job recognition of care worker according to the type of work place shows as follows. As for health care welfare facilities for senior citizens and residential welfare facilities for the elderly was the highest level for physical change and mobile care protection belonging to basic care protection technologies. For the rehabilitation and welfare facility, human rights and prevention of abuse among senior citizens which is belonging to occupational ethics and attitudes of care workers showed the highest. Conclusion: It is required for differentiated job training to enhance capacity for care workers according to the type of work place, and it is needed to developed systematic and specific customized hands-on training to perform, not for simple knowledge.

• Journal of the Society of Disaster Information
• /
• v.18 no.3
• /
• pp.622-635
• /
• 2022

Purpose: Due to the change of demography, the ratio of senior drivers has increased and the transition to a super-aged society is expected to make more seniors drive in the future. Method: In this research, we analyzed medical characteristics of the driver's age-specific decline in body function and saw that both the function of the physical as well as mental capacities deteriorates as people age. Among them, various functions are precipitously weakened after reaching 70, implying that those over the age of 70 are classified as seniors in a medical sense. In this context, we also could identify that based on such age criteria, various safety policies for senior drivers should be developed and set up in Korea. Result: We could find a steep fall in the physical function of body after reaching 70 from the chronological change of cognitive function and judgment ability. In particular, it is revealed that the driving license institution and aptitude test for drivers over 70 should be thoroughly examined, as physical functions necessary for driving such as eyesight and hearing ability is not strong enough in many drivers over 70. Conclusion: Focusing on the physical capacity to drive, we tried to find the hazardous age bracket of senior drivers which might influence driving behaviors. Going forward, we expect this work would help to understand the policies for senior drivers and drivers' physical differences.

• Journal of Korea Trade
• /
• v.23 no.8
• /
• pp.110-131
• /
• 2019

Purpose - This paper investigates the implications for facilitating trade in the products of Industry 4.0. To identify the issues caused by the conflicts of policy objectives such as applying the tariff concession under the ITA and imposing the export control, by exploring the case of classification of drones. Design/methodology - We adopted a single case study method to gain a deeper understanding of the complex and multifaceted issues of Customs classification in the context of facilitating trade in the products of Industry 4.0. This study employs the case of drones to explore how these issues of Customs classification affect trade facilitation. We ensured the internal validity of the study by confirming the pattern of the results with the existing theories. Findings - Our main findings can be summarised as follows: the intrinsic nature of the products that converge several technologies causes issues in the classification. The inconsistency in product classification delays customs clearance by hindering the Customs risk-management system that pinpoints products subject to controls. To address the issues, therefore, we proposed fundamental reforms of Customs to empower themselves with management roles. Facilitating trade in the products of Industry 4.0 requires more enhanced Customs capability. Therefore, the reforms should include comprehensive capacity-building activities, such as changes in staff-trainings, promotion system, organisation and culture. Customs also need roles in robust designing of cooperative systems to compensate for the lacks of controls and to ensure concrete risk management for expedited Customs procedures. As well, by equipping the Single Window of Customs with crucial control functions of other ministries, Customs need to support the cooperation. The role of harmonising various preaudits of other ministries with its own is another essential role that ensures predictability of clearance procedure. Originality/value - There are scanty studies in the field of knowledge about what obstacles exist and what solution is available in the course of transforming to 'Industry 4.0'. In filling out the gap of knowledge, this paper is of academic significance in that it applies the research theory on trade facilitation for the specific cases of classification of the product of Industry 4.0 to verify its effectiveness and to extend the subject of the studies to the scope of Industry 4.0. It also has practical significance in that the results have provided implications for reforms of Customs procedures to facilitate trade in the products of Industry 4.0.