• Journal of Energy Engineering
• /
• v.14 no.4 s.44
• /
• pp.226-231
• /
• 2005

Essentially combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NOx and Particulate Matter (PM) emissions as well as high efficiency under part load. This paper is concerned with the Homogeneous Charge Compression Ignition (HCCI) engine as a new concept in engines and a power source for future automotive applications. In this research, a 4 cylinder diesel engine was converted into a HCCI engine, and propane was used as the fuel. The purpose of this research is to show the effects of fuel flow rate and the temperature of the intake manifold on the performance and exhaust of an HCCI engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.213-221
• /
• 1998

The investigation regarding the ignition system of a plasma jet explored by using a constant volume vessel. The purpose of this study is to elucidate relation between the characteristics of the configuration and jet ejection of plasma jet plug, when the sub energy were supplied at plasma jet ignition system. From the results of a visualization by the schlieren system, the jut ejection for plasma jet ignition are depended on the jet plug configuration and sub energy, but the configuration of plasma jet plug is more influenced than the sub energy on the plasma jet ejection. And the plasma jet ignition strongly influences upon the combustion enhancement than the conventional spark ignition.

• International Journal of Automotive Technology
• /
• v.5 no.3
• /
• pp.195-200
• /
• 2004

This paper is concerned with the Homogeneous Charge Compression Ignition (HCCI) engine as a new concept in engines and a power source for future automotive applications. Essentially a combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NOx and Particulate Matter (PM) emissions as well as high efficiency under part load. The objective of this research is to determine the effects of Exhaust Gas Recirculation (EGR) rate on the combustion processes of HCCI. For this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2088-2093
• /
• 2004

Harmful elements from the exhaust gases are caused by incomplete combustion of mixture inside the engine cylinder and this abnormal combustion like misfire or partial burning is the direct cause of the air pollution and engine performance degradation. In this study, I obtain the shapes of spark, voltage and current generated when changing the experimental parameters such as grounded electrode shapes, electrode gap and the material of center electrodes. After that, I produce ignition energy by using the voltage and current and classify ignition energy into capacitive discharge energy and inductive discharge energy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.209-215
• /
• 2004

This paper presents the frequency range and an analysis method to find the dominant source of electro-magnetic wave which originates from a spark ignition in engine room. Applying the distributed constant equivalent circuit theory the radiation of probable electro-magnetic wave around an ignition plug and a high voltage cable is studied analytically. Experimental studies are also conducted by measuring the frequency spectrum to obtain the radiating characteristics of electro-magnetic wave. Results from both analytical and experimental studies confirm that an ignition plug and a high voltage cable are dominant sources of electro-magnetic wave and that the radiating frequency is ranged from 1.3[GHz] to 2[GHz] band.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3317-3322
• /
• 2007

THC(Total Hydrocarbon) emissions during cold start and warm-up phase constitute the majority of THC emissions during the FTP-75 mode. As the basic approach to improve the emission performance of Gasoline engine during transient phase, the effect of spark timing retard from MBT on THC emission characteristics is studied by engine test using a Fast response Flame Ionization Detector(FFID). A cyclic analysis of the combustion process shows that high THC emissions are produced first few cycles during the transient phase. This paper presents the results of engine performance and emission of Gasoline engine with various spark timing. consequently, This paper was focused on the combustion phenomena with various spark timing during transient phase which was analyzed by Fast response Flame Ionization Detector (FFID) equipment to measure the cyclic THC emission characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.28-35
• /
• 1999

In this study, investigation of transient knock characteristics in a spark-ignition engine has been carried out. The universal knock threshold values were found by a DFDD method and a NSDBP method which is a non-dimensional version of the SDBP method. Also modified NSDBP method could be used for transient knock detection. In a commercial ECU , spark timing was retarded from the steady -state spark timing during rapid throttle opening to avoid uncomfortable feeling and knock. Knock usually occurred just after the start of rapid throttle opening when spark timing was set, as values for the steady state condition. We found that air/fuel ratio deeply involved with the knock during transient condition. Due to the difference of initial heat release rate, knock occurred more easily at rich air/fuel ratio than at lean air/fuel ratio.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.160.2-160
• /
• 2001

This paper presents an individual cylinder spark advance control strategy based upon the location of peak pressure (LPP) in spark ignition engines using artificial neural networks. The LPP is estimated using a feedforward multi-layer perceptron network (MLPN), which needs only five samples of output voltage from the cylinder pressure sensor. The cyclic variation of LPP restricts the gain of the feedback controller, and results in poor regulation performance during the transient operation of the engine. The transient performance of the spark advance controller is improved by adding a feedforward controller which reflects the abrupt changes of the engine operating conditions such as engine speed and manifold absolute pressure (MAP)...

• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1997

In case of using the electrical apparatus in the hazardous atmosphere which exist flammable gas mixtures, There is a dangerosity of gas explosion accident by the electrical spark. The most general method to prevent the explosion by the spark is to use the flame-proof type electrical apparatus to isolate the ignition source. from the flammable atmosphere. But actualy it is impossible to isolate the ignition sources from the atmosphere. So it was needed to find the safe gap which prevent ignition of flammable atmosphere by transmission of flame or heat when a flammable gas mixture exploded inside the apparatus. In this study we tried to find the maximum experimental safe gap(MESG) of $H_2$-air, and $CH_4$-air mixtures by using the 8 litre spherical vessel with 25mm flange. The experiment parameter were ignition position, concentration and initial pressure before explosion. From the experiment the ignition position was affected to the MESG. MESG value was minimum near the stoichiometric concentration of gas mixtures, and according to the increase of initial pressure MESG was decreased.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.368-373
• /
• 2015

As a preliminary study for the development of the gas fueled marine engine, prediction of indicated performances was carried out for a spark-ignition engine using commercial software, GT-POWER. The optimized models through a previous study were applied for the simulation of the intake and exhaust systems in a SI engine. The Spark-Ignition Wiebe model was used to calculate the burn rate in the cylinders and the modified Woschni model was used to calculate the heat transfer to the walls. The predicted performances, such as air delivery, cylinder pressures and indicated mean effective pressures under a range of operating conditions showed good agreement with the experiments.