• 오토저널
• /
• 제15권3호
• /
• pp.120-125
• /
• 1993

The surface roughness of workpiece is reduced during spark-out. The reduction of roughness is a benefit of spark-out, but spark-out lowers productivity. The characteristics of spark-out are different to those of plunge grinding to which feed is applied. This difference is due to overlapping cutting during spark-out. Effect of spark-out is in proportion to volume of grain wear. This phenomenon is due to different overlapping area. Dressing interval can be enlarged by spark-out, when volume of grain wear is large. In this study, the characteristic of spark-out was studied by spark-out obserbation in various grinding conditions. For this purpose thrust force, spark-out time and surface roughness of workpiece were experimentally investigated in various grinding conditions.

• 한국정밀공학회지
• /
• 제13권6호
• /
• pp.52-58
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Through the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding efficiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the residual stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface roughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as possible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20~25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 춘계학술대회 논문집
• /
• pp.425-428
• /
• 1994

Non-uniform minute deformation of a cylinderical workpiece resulted from the heat treatment process prior to the grinding makes it diffeclt to control the approaching feedrate of a grinding wheelto a workpiece optimallywithout on-site detection of the grinding states in the plunge grinding. The 4-stage model of the plunge grinding process is proposed according to the state of contact between grinding wheel and workpiece ; precontact, partial contact, entire contact and spark-out. Despite of being scrious to the precision of workpiece finished, the duration of spark-out is determined empirically. The purpose of this research is to develop a monitoring/control system for saving non- production time and setting the optimal spark-out time based on sensor information in the plunge grinding using AE and ultra sonic sensor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.39-43
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Though the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding effciiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the resiudal stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface foughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as polssible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20 .approx. 25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.614-623
• /
• 2005

This study aims to perform the characteristic evaluation of surface grinding for the STD11 material with experimental and analytic techniques based on the response surface model. The grinding force acting on the workpiece and the ground surface roughness were measured according to the change of grain size, table speed and depth of cut. The effect of spark-out on the grinding force and the surface roughness was also characterized. The frictional coefficient between workpiece and grinding wheel could be determined by the analysis of spark-out effect. From the experimental data, the second-order response surface models were developed to predict the grinding force and the surface roughness. Validation of the developed model was examined.

• 대한기계학회논문집A
• /
• 제23권6호
• /
• pp.881-894
• /
• 1999

Cylindrical plunge grinding is widely used for final machining process of precision parts such as automobile, aircraft, measurement units. But in order to make parts which have high precision accuracy and high surface integrity, it is necessary to consider grinding characteristics due to accumulation phenomena of grinding wheel in plunge grinding process. In this study, in order to examine closely plunge grinding process, grinding power, grinding force, real depth of cut are monitored in transient state, steady state and spark out state. As the result, it is shown that grinding power and force are affected by dressing condition, depth of cut and speed ratio and that there exist threshold grinding force and it also affected by dressing condition. Also considered effects of grinding conditions on surface roughness and roundness of workpiece

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.55-61
• /
• 2015

In this paper, the grinding characteristics of internal thrust grinding were studied with vitreous CBN wheels using a machining center. Grinding experiments were performed according to grinding conditions, such as wheel feed speed and depth of cut, workpiece speed, and rate of grinding width. Additionally, the grinding force and grinding ratio were investigated though these experiments. Based on the experimental results, the grinding characteristics of internal thrust grinding were discussed.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.

• 한국정밀공학회지
• /
• 제12권9호
• /
• pp.66-73
• /
• 1995

This paper presents monitoring and control system to decrease non-production time such as air grinding and partial contact in cylindrical plunge grindings. The 4-stage model of the plunge grinding process is proposed according to the state of contact between grinding wheel and workpiece; air grinding, partial contact, entire contact and spark out. Experimentally it is seen that the AE sensor and ultrasonic sensor are very effective to detect the grinding states. Monitoring and control algorithm using recognized grinding process was introduced and a experiment were conducted to verify the developed system.

• 한국정밀공학회지
• /
• 제10권1호
• /
• pp.42-51
• /
• 1993

Recently, WC-Co have some excellent properities as the material for the mechanical component such as metallic moulding parts, ball dies parts, and punch parts. This paper describes the surface roughness and grinding force caused by experimental study on the surface grinding of WC-Co with ultra-precision like a mirror shape using diamond wheel. Also, some investigations are carried out using WA grinding wheel to increase improved ground surface roughness such as polishing, lapping effect. Some important results obtained here are summarized as follow. 1) Within this experimental grinding condition, we can be obtained $R_{max}.\;2\mu\textrm{m}\;R_a\;0.3\mu\textrm{m}$ whichare the most favourable ground surface roughness using #140 diamond wheel, and improved surface roughness values about 20 .approx. 25% throughout 5 times sparkout grinding 2) The value of surface roughness is Rmax. $0.49\mu\textrm{m},\;R_a\;0.06\mu\textrm{m}$ using #600 diamond wheel. 3) The area of no rack zone is less than $F_{n}$ 0.27N/mm, Ft 0.009N/mm