• 전기의세계
• /
• 제28권1호
• /
• pp.73-82
• /
• 1979

There are a great number of papers on the Townsend discharge in gases, and many of them are concerned with the effect of the cathode. It has been regarded that there are two kinds of effect of the electrodes, especially of the cathode; (a) the effect caused by the difference of the cathode material and (b) the effect by the change of the cathode surface state even in the same material. Both of them may change the secondary coefficient following after the change of the work function, and the atter may further change the primary ionization coefficient as foreign atoms on the surface may be dseorbed in sparks to decrease the purity of the gas. Thus the two effects must be investigated independently to study the roles of the cathode in gas discharges. In this report the effect of the cathode material on the sparking voltage is described. The experiment is also carried out under the condition that the desorption of impurities from the cathode be negligible. From these the new correlativity between the work function of the cathode and the sparking voltage is obtained. In addition, the interesting character of the minimum point of the Paschen's curve can be found.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 방전 플라즈마 유기절연재료 초전도 자성체연구회
• /
• pp.104-108
• /
• 2004

The effect of magnetic field was measured on NOx removal for cylinder-wire plasma reactor with magnetic field applied to electric field vertically. Power was supplied to plasma reactor using rotating spark gap switch. Consumption power increased with increasing discharge voltage. When magnetic field was applied to electric field vertically, consumption power was less than that without magnetic field because of lorenz's force. NOx removal rate of plasma reactor with magnetic field were higher, 10-15%, than that of plsama reactor without magnetic field. And NOx removal rate decreased with increasing gas flow rate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.366-369
• /
• 2005

Electrochemical discharge machining (ECDM) has been found to be potential fur the micro-machining of non-conductive materials such as ceramics or glass. However this machining process has its own inherent problem that the reproducibility is too low to get the available geometric accuracy fur micromachining applications. One main challenge in reaching this goal is the control of the hydrogen built around the tool-electrode in which happen the discharges. This paper proposes the methods to improve the geometric accuracy using powder-mixed ECDM process. The experimental results show the effects of powder producing improved geometric accuracy by averaging and decreasing the concentration of spark energy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2195-2197
• /
• 1999

Electric breakdown in the liquid produces a spark channel. The energy input into the channel causes expansion of a vapor gas cavity. If the power of the discharge is high enough, this expansion is fast enough to produce a shock wave which propagates through the liquid to the subject of destruction. We focused our attention on the correlation between electric parameters and the characteristics of the flash caused by point to-point electrode discharge in the water. By varying firing voltage and gap length, we obtained the features of the flash : amplitude, pulse width, and so on. In this paper, We have known that there is a concrete interrelation between underwater firing voltage and photodiode output.

• 한국가스학회지
• /
• 제2권4호
• /
• pp.79-84
• /
• 1998

본 논문은 고주파 발생장치와 IEC형 불꽃점화 시험장치를 이용하여 라디오 주파수 범위내에서 발생하는 개폐불꽃에 의한 LPG-Air 5.25[Vol$\%$]의 혼합가스에 대한 최소점화한계전압을 구하였다. 그 결과 LPG-Air 혼합가스는 주파수가 높을수록 최소점화한계전압도 높아졌으며, 특히 3[KHz]에서 10[KHz]사이에서 현저히 증가함을 알 수 있었다. 이는 3[KHz]까지는 1회의 방전에너지에 의해 점화가 발생되지만 3[KHz]이상에서는 2회 이상의 방전에너지가 누적되어 점화가 일어남을 알 수 있었고 그 이유는 방전과 방전간의 휴지기간이 존재하므로써 생기는 에너지의 손실이 그 원인으로 생각된다. 본 연구결과는 가스가 존재하는 위험장소에서도 안전하게 사용될 수 있는 통신장비나 각종탐지기 등에 응용될 수 있는 본질안전 방폭형 고주파 전기기기의 연구개발을 위한 기본자료로서 뿐만 아니라 이들 장비의 방폭성능에 대한 시험자료로도 활용가능할 것으로 사료된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1394-1397
• /
• 1995

In the hazardous areas where explosive gases, vapor or mists exist, electrical apparatus and installations must be of explosion-proof construction to prevent or limit the danger of the ignition of potentially explosive atmosphere. In Korea, nine types of protection have been specified in the government regulations at present: flameproof enclosure, pressurization, oil immersion, increased safety, intrinsic safety, non-incendive, sand filling, encapsulation, and special types. Among these types, the intrinsic safety has the construction which limit or by-pass igniting the electric energy using electronic devices. This type has lots of merits but at the same time requires a high-degree of technology. In this paper, we investigated several dominating factors which affect the minimum ignition energy: this energy plays a very important role in design and evaluation of the intrinsic safety type electrical apparatus. Eletrode material, which is one of the most important factors, was intensively studied for the five sorts of material(Al, Cd, Mg, Sn, and Zn) with performing experiment in a low-voltage inductive circuit using IEC-type spark apparatus. The experimental results show that the minimum ignition energy of electrode material is varied: highest in Cd and lowest in Sn. We also confirmed the effect of eletrode make-and-break speed and magnetic field magnitude.

• 대한기계학회논문집A
• /
• 제27권10호
• /
• pp.1800-1808
• /
• 2003

This work deals with the electrical conductivity of dielectric on output parameters such as metal removal rate and surface roughness value of a carbon steel(SM25C) and sintered carbides cut by wire-electrical discharge machining(W-EDM). Dielectric has several functions like insulation, ionization, cooling, the removal of waste metal particles. The presence of minute particles(gap debris) in spark gap contaminates and lowers the breakdown strength of dielectric. And it is considered that too much debris in spark gap is generally believed to be the cause of arcing. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a lower metal removal rate because the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. Debris were analyzed also through scanning electron microscopy(SEM) and surface roughness tester. Micro cracks and some of electrode material are found on the workpiece surface by energy dispersive spectrometer(EDS).

• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.15-21
• /
• 2006

This work deals with the electrical conductivity of dielectric on output parameters such as metal removal rate and surface roughness value of a carbon steel(SM25C) and sintered carbides cut by wire electrical discharge machining (WEDM). Dielectric has several functions like insulation, ionization, cooling, the removal of waste metal particles. The presence of minute metal particles(debris) in spark gap contaminates and lowers the breakdown strength of dielectric. And it is considered that too much debris in spark gap is generally believed to be the cause of arcing. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a lower metal removal rate because the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. Debris were analyzed also through scanning electron microscopy(SEM) and surface roughness tester. Micro cracks and some of electrode material are found on the workpiece surface by energy dispersive spectrometer(EDS).

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.130-137
• /
• 1997

The demand for wire-cut EDM is increasing rapidly in the die and tool making industry. In this study machining characteristics such as machining rate, surface roughness, hand drum form and hardness of machined material are investigated experimentally under the conditions varing pulse on time, pulse off time, peak voltage, wire tension after fixing other conditions in SKD 11 and brass and brass workpiece. It was found that various operating conditions had significant influences on machining characteristics. But the hardness of workpiece was uneffected by operating conditions. Also it was obtained experimentally that brass workpeice had better machinability than SKD 11 one.dition according to the current(Ip) in an electric spark machine : 1) Electrode is utilized Cu and Graphite. 2) Work piece is used the material of carbon steel. The condition of experiment is : 1) Current is varied 0.7(A) to 50(A) and the time of electric discharging to work piece in each time is 30(min) to 60(min). 2) After the upper side of work piece was measured in radius(5$\mu$m) of stylus analyzed the surface roughness to ade the table and graph of Rmax by yielding data. 3) Electro wear ratio is : \circled1Cooper was measured ex-machining and post-machining by the electronic balance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume $\times$specific gravity and analyzed to made its table and graph on ground the data. 4) In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V. R and the memory scope was sticked to the electric spark machine. 5) In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid , it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging.