• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.43-49
• /
• 1997

The lengths of fibers and vessel elements, vessel diameters, and ray spacings of tension and opposite woods in Quercus mongolica Fischer and their radial variations were examined. Crystallinity indices and crystallites orientations of tension, opposite and lateral woods were also investigated. The lengths of fibers and vessel elements, and ray spacings of tension wood were longer and denser than those of opposite wood, respectively. In the latewood, the vessels of tension wood had a little larger diameters than those of opposite wood. whereas the vessel diameters of earlywood were similar in both woods. With the exception of vessel diameters of earlywood, there were differences between tension and opposite woods in all anatomical characteristics examined. In the radial variation pattern, the fiber lengths of both woods increased markedly to about 15th annual ring and thereafter remained virtually constant. The vessel element lengths of earlywood in tension wood increased to certain annual ring and thereafter were stabilized, but opposite wood had a relatively constant trend from pith to bark. Those of late wood in both woods increased to certain annual ring and thereafter showed constant patterns. Vessel diameters appeared to show similar trend in both woods. Ray spacings decreased to about 15 annual ring and thereafter were stabilized in both woods. In the fine structures, tension wood had higher crystallinity index and better crystallites orientation than opposite and lateral woods.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.4
• /
• pp.173-179
• /
• 2020

The purpose of this study was to investigate comparatively the microstructural characteristics and hardness of discontinuous precipitates (DPs) in Mg-9%Al alloy, which were formed by continuous cooling (CC) from 678 K to RT and isothermal aging (IA) at 413 K, respectively. In as-cast state, the Mg-9%Al alloy consisted of partially divorced eutectic β(Mg₁₇Al₁₂) particles with a small amount of DPs showing (α+β) lamellar morphology adjacent to the β particles. The DPs formed by CC had interlamellar spacings in a broad range of 0.85~2.12 ㎛ (1.51 ㎛ in average) owing to the various formation temperatures in response to continuous cooling process. Meanwhile, the DPs formed by IA had relatively narrower interlamellar spacings of 0.14~0.29 ㎛ (0.21 ㎛ in average), which is associated with the low and constant formation temperature. Thinner and higher volume fraction of β phase layers were noticeable in the DPs formed by IA. Higher hardness values were obtained in the DPs formed by IA than the DPs formed by CC, which may well be ascribed to the finer lamellar structure and higher β phase content of the DPs formed by IA.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.11
• /
• pp.1478-1485
• /
• 2000

An experimental study has been performed to investigated the forced convection heat transfer characteristics of 6 circular cylinders in staggered arrangement in a cross flow of air. The water scale deposited on condenser wall of power plant was used to investigate the effect of roughness of scaled surfaces. The relative roughness*average diameter of scale/cylinder diameter) was in a range of k/d=0.0066, 0.0111, 0.0167, 0.0222 and 0.0278. The cylinder spacings(L/d) varies from 1.5 to 4.0 where L denote the cylinder spacings along and normal to the upstream uniform flow direction. The Reynolds number was varied in a range of 10, 000$\leq$ Re $\leq$ 50,000. The local and mean Nusselt numbers were investigated as a function of scale roughness, the cylinder spacing and Reynolds number. The results are compared with those of clean cylinder and inline tube bank, subsequently the mean fouling resistance over the entire circumference was estimated from those results as a function of scale roughness, the cylinder spacing and Reynolds number.

• Economic and Environmental Geology
• /
• v.32 no.3
• /
• pp.307-315
• /
• 1999

Four organic polymers were mixed with mothmorillonite. Two cationic polymers a hi로 molecular weight polyacrylamide (494C) and a low molecular weight polymer (587C).Two anionic polymers include a high molecular weight polymer (aerotil). Each clay supension series were allowed to stand for 24 hours and were centrifuged, and the clay plugs were washed and dried. The dried samples investigated by XRD, IR and CEC measurement. The suspended clay containing anionic polymers was not flocculated at any concentratuons of polymer. But the suspendions containing two cationic polymers were rapidly flocculated at almost all concentrations. the d(001) spacings of Na-montmorillonite after being with cationic polymer 587C show about 15$\AA$ suggesting the polymers may have entered the interlayer spaces. The polymer 494C-treated sample produced double peaks of about 12 and 15$\AA$ in XRD. It indicates that the high molecular weight polymer. And cationic polymer 494C may be adsorbed mainy on the outside surface of clay, and some polymers may peretrate into olny interlayers in the margin of montmorillonite particles because of its high molecular weught. CEC of polumer 587-treated sample was reduecd mmarkedly suggesting polymer blocks CEC sites. The d(001) spacings of Ca-montmorillonite after being treated with cationic polymers show about 15$\AA$ suggesting that the interlayer spaces have not been expanded. In the experiment using a dilute Ca-bearing solution, the suspended caly containinf anionic polymers was flocculated. The results indicate that the flocculation behavior of montmorillonite-polymer supension depends on not only polymer properties such as concentration, electric charge and molecular weight but also compositions of solvent.

• Journal of Biosystems Engineering
• /
• v.28 no.5
• /
• pp.395-402
• /
• 2003

Standard ginseng seedling, selected after one year's rearing in the seedling bed has been conventionally transplanted in Korea. Recently, the direct seeding areas have been increasing to product high quality ginsengs for red-ginseng processing. Reciprocating push-rod brush, holed-roller and vacuum suction seeders, planting with 30 ${\times}$ 30mm spacings and adjustable to the folds were designed and theirs performances were evaluated. The developed three types of seeders reliably performed at the success rate over 95% with less than 10% in slip rate, and could be used a seeder for the greater spacings by adjusting metering parts. The research concluded that the vacuum suction seeder was the most feasible and practical with the greatest metering success and the least slip among three type seeders of the reciprocating push-rod brush, holed-roller and vacuum suction seeders. The vacuum suction seeder holds a seed with each needle nozzle using the negative pressure created by a vacuum pump. The capacity was 24.5 times greater than a man power at the speed of 5 m/min.

• Journal of Korea Foundry Society
• /
• v.3 no.1
• /
• pp.3-12
• /
• 1983

The influence of columnar dendirtes on the mechanical properties of Al-1% Cu alloys as unifirectionalloy solidified under the conditions of controlled crystal growth rate (R) and temperature gradient (G) was investigated. And the change of metallography and mechanical properties when unifirectionalloy solidified alloys and cast alloys were cold-rolled from 10% to 90% in reduction ratio was studied. The results are as follows: 1. The elongation and yield strength of unifirectionalloy solidified alloy are higher then those of cast alloy, but there is a little decrease in ultimate tensile strength. 2. The metallography and mechanical properties are changeable with the primary arm spacings when the unidirectionalloy solidified alloys were cold-rolled from 10% to 90% in reduction ratio. An alloy with larger primary arm spacings was easily changeable in metallography and mechanical properties when it was cold-rolled. 3. The tensile strength of transversely cold-rolled to 90% in reduction ratio was higher then that of longitudionalloy cold-rolled to 90% in reduction ratio. In the case, the fractorgraphs of fractured surface showed that the cast alloy and the unifirectionalloy solidified alloy was ductile-fractured, but the surface of transversely cold-rolled to 90% reduction of unidirection alloy solidified was slip plane qracture.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.28-37
• /
• 1992

Fine structures of some Korean woods were investigated by X-ray diffraction methods. Relative crystallinity measured by the Segal's method and by the area method was $53{\pm}6%$ and $43{\pm}8%$ in softwoods, and $54{\pm}5%$ and $45{\pm}5%$ in hardwoods, respectively. The crystallite dimension in width was $3.11{\pm}0.45nm$ in softwoods and $3.22{\pm}0.25nm$ in hardwoods. In the longitudinal direction, the dimension was $12.79{\pm}0.89nm$ in softwoods and $12.60{\pm}0.72nm$ in hardwoods. The d-spacings of (200) in equatorial and (004) in meridional layers were about 0. 397 run and about. 0.260 nm, respectively. As a result, relative crystallinity, crystallite dimensions and d-spacings of (200) did not show any differences between the softwoods and hardwoods. The ratio of integrated intensities of (002) and (004), however, showed some differences between the softwoods and hardwoods. Namely, it was $0.101{\pm}0.027$ in softwoods and $0.138{\pm}0.037$ in hardwoods.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.515-520
• /
• 2005

The behavior of jointed rock mass is much different from that of intact rock due to the presence of joints. Similarly, the characteristics of elastic wave propagation in jointed rock are considerably different from those of intact rock. The propagation of elastic waves in jointed rock is greatly dependent on the state of stress. The roughness, filling materials, and spacing of joints also affect wave propagation in jointed rock. If the wavelength of elastic waves is much larger than the spacing between joints, wave propagation in jointed rock mass can be considered as wave propagation in equivalent continuum. A rock resonant column testing apparatus is made to measure elastic waves propagating through jointed rock in the state of equivalent continuum. Three types of wave, i.e, torsional, longitudinal and flexural waves are monitored during rock resonant column tests. Various roughness and filling materials are applied to joints, and rock columns with various spacings are used to understand how these factors affect wave propagation under a small strain condition. The experimental results suggest that the characteristics of wave propagation in jointed rock mass are governed by the state of stress and influenced by roughness, filling materials and joint spacings.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.29-32
• /
• 2000

Ozone has been widely applied to many industrial fields because of its strong oxidation effects. Therefore, the studies have been progressed for the effective and high concentration of one generation. The silent or surface discharge have been mainly used for high concentration ozone generation until now. But these two types of ozone generators have shortcomings to be improved. In this study, the ozone generator which improved the shortcomings of above two type of ozone generators was proposed and manufactured for high concentration ozone generation. And the proposed ozone generator could generate the surface and barrier discharge simultaneously. For this purpose, a mesh type discharge electrodes were proposed and the experiments were fulfilled as a function of the widths and spacings of mesh electrodes and gap spacings between the dielectric barrier and mesh electrode. When the width of mesh electrode[WM] and spacing of mesh electrode[SM] are 0.3[mm] and 0.8[mm] respectively, the maximum ozone concentration of 2.96[vol%] was obtained at 5.6[kV], 830[mA], gap spacing (S)=0.65[mm].

• Journal of Mechanical Science and Technology
• /
• v.19 no.9
• /
• pp.1801-1810
• /
• 2005

The effect of longitudinal thin rectangular riblets aligned with the flow direction on turbulent channel flow has been investigated using direct numerical simulation. The thin riblets have been modeled using the immersed boundary method (IBM) where the velocities at only one set of vertical nodes at the riblets positions are enforced to be zeros. Different spacings, ranging between 11 and 43 wall units, have been simulated aiming at getting the optimum spacing corresponding to the maximum drag reduction while keeping the height/spacing ratio at 0.5. Reynolds number based on the friction velocity ${\mu}_\tau$ and the channel half depth $\delta$ is set to 150. The flow is driven by adjusted pressure gradient so that the mass flow rate is kept constant in all the simulations. This study shows similar trend of the drag ratio to that of the experiments at the different spacings. Also, this research provides an optimum spacing of around 17 wall units leading to maximum drag reduction as experimental data. Explanation of drag increasing/decreasing mechanism is highlighted.