• Journal of Korean Society of Steel Construction
• /
• v.16 no.3 s.70
• /
• pp.333-344
• /
• 2004

In civil engineering applications, the establishment of standards and procedures for analysis, design, fabrication, construction, and quality control are essential in facilitating the economic and efficient use of composite materials. Many bridge systems, including girders. cross beams, and concrete decks, function as specially orthotropic plates. in general, the analytical solution for such complex systems is very difficult to achieve. Thus, the finite difference method is used for the analysis of the problem. The rate of tensile strength reduction due to increased size is considered. Strength reduction is necessary to ensure the safe design of building structures. This paper suggests the use of a strength-failure analysis procedure using the reduced tensile strength. A numerical study is conducted for different cases. The Tasi-Wu failure criterion for stress space is also used.

• Journal of Biosystems Engineering
• /
• v.28 no.5
• /
• pp.429-438
• /
• 2003

This study exploits the robot system which is necessary in gene study and bio-technology industry. As well, a DNA chip, which of use has been increased recently, can be manufactured with this system. The robot consists of a device spotting DNA on the silylated slide, a well plate, a bed for fixing well plates, devices of washing and drying the pin in DNA spotting .device, a distillation-water vessel, and a discharge vessel of wash water. We made the period of sticking DNA to the pin on the well plate to be 15 seconds. The spot size of DNA was set to be 0.28 mm on the average by bringing the slide into contact with pin during 1 second. If DNA is spotted in minimum space possible about 0.32mm, this system can stick about 8,100 DNA spots on the well plate with this rate. Analyzing the procedure: Movement starts, Pin washes, dries, and smears DNA on the well plate. Spotting DNA onto 12 chips took 2 minutes and 50 seconds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.274-275
• /
• 2006

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. Linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 17 [%] under the speed 0.14 [m/s], thrust 345 [gf] and preload 280 [gf], operating frequency is 57.6 [kHz].

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.3
• /
• pp.1-15
• /
• 1992

A Practical and easily applicable methods for the numerical analysis and the optimum design of continuous and horizontally curved two-way slab systems with twelve possible edge conditions are presented. The proposed method for the numerical structural analysis is based on the use of design moment coefficients which are derived from the elastic theory of thin curved plates. The optimum values are selected from within the feasible region in the design space defined by the limit state requirements. The sequential linear programming is introduced as an analytical method of nonlinear optimization. The optimum design variables, including a effective depth and transformed steel ratios per unit width of middle and column strips of slabs, are then determined.

• Mycobiology
• /
• v.47 no.1
• /
• pp.126-133
• /
• 2019

Isaria javanica pf185 is an important entomopathogenic fungus with potential for use as an agricultural biocontrol agent. However, the effect of I. javanica pf185 on plant growth is unknown. Enhanced tobacco growth was observed when tobacco roots were exposed to spores, cultures, and fungal cell-free culture supernatants of this fungus. Tobacco seedlings were also exposed to the volatiles of I. javanica pf185 in vitro using I-plates in which the plant and fungus were growing in separate compartments connected only by air space. The length and weight of seedlings, content of leaf chlorophyll, and number of root branches were significantly increased by the fungal volatiles. Heptane, 3-hexanone, 2,4-dimethylhexane, and 2-nonanone were detected, by solid-phase micro-extraction and gas chromatography-mass spectrophotometry, as the key volatile compounds produced by I. javanica pf185. These findings illustrate that I. javanica pf185 can be used to promote plant growth, and also as a biocontrol agent of insect and plant diseases. Further studies are necessary to elucidate the mechanisms by which I. javanica pf185 promotes plant growth.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.910-912
• /
• 2006

Barrier ribs in plasma display panels (PDPs) function to maintain the discharge space between the glass plates as well as to prevent optical cross-talking. The barrier ribs currently employed are typically $300{\mu}m$ pitch, $110{\sim}120{\mu}m$ in height, with upper and lower widths of $50{\mu}m$ and $80{\mu}m$, respectively. It has been reported that barrier ribs can be fabricated by screen-printing, sand blasting, etching and photolithographic processes. In this study, photosensitive barrier rib pastes were formulated and systematically evaluated in terms of photolithographic process variables such as printing, drying, UV exposure, development and sintering. It was found that the use of UV absorbent, polymerization inhibitor and surfactant were very effective in controlling the width uniformity of barrier ribs in the photolithographic method of barrier rib patterning.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.823-827
• /
• 2005

Barrier ribs in the plasma display panel (PDP) function to maintain the discharge space between the glass plates as well as to prevent optical crosstalk. Patterning of barrier ribs is one of unique processes for making PDP. Barrier ribs could be formed by screen-printing, sand blasting, etching, and photolithographic process. In this work photosensitive barrier rib pastes were prepared by incorporating binder polymer, solvent, functional monomers photoinitiator, and barrier rib powder of which surface was treated with fumed silica particles. Studies on the function of materials for the barrier rib paste were undertaken. After optimization of paste formulation and photolithographic process, it was applied to the photosensitive barrier rib green sheet and was found that photolithographic patterning of barrier ribs could be formed with good resolution up to $110{\mu}m$ height and $60{\mu}m$ width after sintering.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.651-656
• /
• 2017

In this study, we designed the system that helps drivers check all information about parking space at the entrance and find out whether the places is available or not, because the system has 'Image recognition function' which can even recognize car number plates exactly. Besides, we place the webcam close to the car number plate, so that car number can be identified more quickly. Finally, since we set the webcam high, the system keeps us from parking wrong places by displaying on the screen.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.2
• /
• pp.58-62
• /
• 2019

Diffractive Optical Elements(DOEs) diffracts incident light using the diffraction phenomenon of light to generate a desired diffraction image. In recent years, the use of diffraction optics, which can replace existing refractive optical elements with flat plates, has been increased by implementing various optical functions that could not be implemented in refractive optical devices and by becoming miniaturized and compacted optical elements. Direct laser lithography is typically used to effectively fabrication such a diffractive optical element in a large area with a low process cost. In this study, the process conditions for fabricating patterns of diffractive optical elements in various shapes were found using direct laser lithographic system, and optical performance evaluation was performed through fabrication.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1093-1098
• /
• 2017

In this study, we designed the system that helps drivers check all information about parking space at the entrance and find out whether the places is available or not, because the system has 'Image recognition function' which can even recognize car number plates exactly. Besides, we place the webcam close to the car number plate, so that car number can be identified more quickly. Finally, since we set the webcam high, the system keeps us from parking wrong places by displaying on the screen.