• Progress in Superconductivity
• /
• 제3권2호
• /
• pp.224-228
• /
• 2002

We investigated the quench properties of superconducting fault current limiters (SFCLs) connected in parallel. It was carried out as an effort to scale up the current capacity of SFCL toys texts. SFCLs were based on $YBa_2$$Cu_3$$O_{7}$ films coated in-situ with a gold layer and fabricated by patterning the films into 2 mm wide and 42 cm long meander lines by photolithography. Two SFCLS were connected in parallel and tested with simulated AC fault currents. Initially the current was divided unequally into branches of parallel connection due to unequal resistance of the branches. However, once quench started in the SFCLs, the current oscillated between the branches and then was distributed nearly equally between the branches. In other words, the elements quenched simultaneously. The oscillation amplitude decreased as the source voltage was increased: the oscillation was the most prominent near the quench current. The observed oscillation and the consequent simultaneous quench was understood in terms of quench start and development in the SFCLs.

• Journal of Power Electronics
• /
• 제14권3호
• /
• pp.531-540
• /
• 2014

A novel carrier-based PWM (CBPWM) strategy of a three-level NPC converter is proposed in this paper. The novel strategy can eliminate the low-frequency neutral point (NP) voltage oscillation under the entire modulation index and full power factor. The basic principle of the novel strategy is introduced. The internal modulation wave relationship between the novel CBPWM strategy and traditional SPWM strategy is also studied. All 64 modulation wave solutions of the CBPWM strategy are derived. Furthermore, the proposed CBPWM strategy is compared with traditional SPWM strategy regarding the output phase voltage THD characteristics, DC voltage utilization ratio, and device switching losses. Comparison results show that the proposed strategy does not cause NP voltage oscillation. As a result, no low-frequency harmonics occur on output line-to-line voltage and phase current. The novel strategy also has higher DC voltage utilization ratio (15.47% higher than that of SPWM strategy), whereas it causes larger device switching losses (4/3 times of SPWM strategy). The effectiveness of the proposed modulation strategy is verified by simulation and experiment results.

• 천문학회보
• /
• 제44권2호
• /
• pp.40.3-40.3
• /
• 2019

Our recent observations of the Sun through strong spectral lines have revealed several important properties of the three-minute umbral oscillations inside sunspots -- the oscillations of intensity and Doppler velocity with periods of 2 to 3 minutes. The oscillations usually occur in the form of a time series of oscillation packets each of which lasts 10 to 20 minutes, not as continuous trains. Each oscillation packet is characterized by a singly peaked power spectrum of velocity oscillation. The oscillations propagate in the vertical direction from the photosphere to the corona. In the upper chromosphere, they develop into shocks that eventually collide with the transition region. When shocks propagate along a highly inclined direction, the merging of two successive shocks can take place. Once they enter the corona, they change to linear compressional waves. In the image plane, the three-minute oscillations propagate with high speeds in the transverse direction as well, usually propagating radially outwards from a point, and sometimes accompanying spiraling patterns of Doppler velocity. These observational properties can be theoretically explained by postulating the spatio-temporally localized source of fast MHD waves at a depth of about 2000 km below the surface, the excitation of slow MHD waves via mode conversion near the photosphere, and the resonance of the slow waves in the photospheric layer below the temperature minimum, and the nonlinear development of slow waves in the chromosphere.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.645-648
• /
• 1991

In conventional sinusoidal wave PWM control, torque oscillation is a problem on account of harmonic component. This paper deals with the choice of line-to-line voltage modulation method, which is effective in using DC(direct current) source voltage and in controlling harmonic oscillation, and the pattern to reduce swiching loss through 1/3 pause of switching interral. So, this paper deals with valid realization of harmonic component and high torque response on variable load by simulation and experiments to compensate occurring problems when line-to-line modulation are applied to PWM inverter.

• 전기학회논문지
• /
• 제56권5호
• /
• pp.829-833
• /
• 2007

In this paper, the RCF method is applied to analyze small signal stability of power systems including GTO controlled parallel FACTS equipments such as STATCOM. To apply the RCF method in power system small signal stability problems, state transition equations of generator, controllers and STATCOM are presented. In eigenvalue analysis of power systems, STATCOM is modelled as the equivalents voltage source model and the PWM switching circuit model. As a result of simulation, the RCF method is very powerful to calculate the oscillation modes exactly after the switching operations, and useful to analyze the small signal stability of power systems with periodically operated switching devices such as STATCOM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.228-229
• /
• 2006

The RCF analysis method is used to analyze small signal stability of power systems including GTO controlled FACTS equipment such as STATCOM. To apply the RCF analysis method in power system small signal stability problems, the state transition equations of power system equipments and power systems with STATCOM are presented. In eigenvalue analysis of power systems by the RCF analysis method, the STATCOM is modelled into the equivalents voltage source model and the PWM switching circuit model. As a result of simulation, the RCF analysis method is very powerful to calculate the oscillation modes exactly after the switching operations, and useful to analyze the small signal stability of power systems with periodically operated switching device such as the STATCOM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2207-2208
• /
• 1999

In this paper, we would like to study the oscillation characteristics of single mode fiber laser which is composed of a Fabry-Perot resonator, a pump source of 808nm Laser Diode, a $Er^{3+}$ doped single mode fiber with 0.5um diameter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 D
• /
• pp.848-850
• /
• 1997

A control method of UPFC (Unified Power Flow Controller) to reduce low frequency oscillation is proposed. UPFC is modelled by voltage source, which magnitude and phase angle can be controlled. Because there needs some time to change to desired value, d-axis voltage and Q-axis voltage is modeled by 1st order delay. LQG(Linear Quadratic Gaussian) is used. It is shown that low frequency can be damped by control of UPFC effectively.

• 대한조선학회지
• /
• 제27권1호
• /
• pp.57-62
• /
• 1990

본 논문에서는 표면장력 효과를 포함한 선형포텐셜이론을 이용하여 전진하며 동요하는 2차원 소오스에 의하여 발생되는 자유표면파를 해석하였다. 속도를 U, 진동수를 $\omega$ 그리고 중력가속도를 g라 할 때, ${\tau}=U{\omega}/g$로 정의된 무차원 진동수가 임계치 1/4보다 작을 때에는 6개의 파성분이 나타남을 보였다. 이 중에서 특히 2개의 파성분은 표면장력의 영향을 지배적으로 받아 소오스 앞면에 발생하는 데, 그중 하나는 전진속도 방향으로 다른 하나는 반대방향으로 매우 느리게 전파한다. 동요수가 작을 경우에는 표면장력의 영향이 약해지며 임계치 1/4보다 조금 큰 진동수에서 공진이 발생한다. 그러나 동요수가 클 때에는 (${\upsilon}={\omega}^2/g>20$) 표면장력효과가 크게 작용하여 발생파의 진폭이 감소하며 분산되어 임계치에서의 공진현상이 사라진다. 한편 전진속도가 표면장력파의 최소위상속도인 0.232m/sec일 때어는 해가 존재하지 않는다.

• Journal of electromagnetic engineering and science
• /
• 제15권4호
• /
• pp.232-238
• /
• 2015

This work describes the development of a D-band (110-170 GHz) signal source based on a SiGe BiCMOS technology. This D-band signal source consists of a V-band (50-75 GHz) oscillator, a V-band amplifier, and a D-band frequency doubler. The V-band signal from the oscillator is amplified for power boost, and then the frequency is doubled for D-band signal generation. The V-band oscillator showed an output power of 2.7 dBm at 67.3 GHz. Including a buffer stage, it had a DC power consumption of 145 mW. The peak gain of the V-band amplifier was 10.9 dB, which was achieved at 64.0 GHz and consumed 110 mW of DC power. The active frequency doubler consumed 60 mW for D-band signal generation. The integrated D-band source exhibited a measured output oscillation frequency of 133.2 GHz with an output power of 3.1 dBm and a phase noise of -107.2 dBc/Hz at 10 MHz offset. The chip size is $900{\times}1,890{\mu}m^2$, including RF and DC pads.