• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.619-619
• /
• 2013

The interfacial state between $Ta_2O_5$ and a Si substrate during the growth of $Ta_2O_5$ films by atomic layer deposition (ALD) was investigated using in-situ synchrotron radiation photoemission spectroscopy (SRPES). A newly synthesized liquid precursor Ta($N^tBu$) $(dmamp)_2Me$ was used as the metal precursor, with Ar as a purging gas and $H_2O$ as the oxidant source. After each half reaction cycle, samples were analyzed using in-situ SRPES under ultrahigh vacuum at room temperature. SRPES analysis revealed that Ta suboxide and Si dioxide were formed at the initial stages of $Ta_2O_5$ growth. However, the Ta suboxide states almostdisappeared as the ALD cycles progressed. Consequently, the $Ta^{5+}$ state, which corresponds with the stoichiometric $Ta_2O_5$, only appeared after 4.0 cycles. Additionally, tantalum silicate was not detected at the interfacial states between $Ta_2O_5$ and Si. The measured valence band offset between $Ta_2O_5$ and the Si substrate was 3.22 eV after 3.0 cycles.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.896-901
• /
• 2002

Since many process parameters of FHD(Flame Hydrolysis Deposition) are involved in forming multi-component amorphous silica film ($SiO_2-B_2O_3-P_2O_5-GeO_2$), it has not been easy to predict the optical, mechanical and thermal properties of deposited film from the simple process parameters, such as source flow rate. Furthermore, the prediction of final composition of film becomes even more difficult after sintering at high temperature due to the evaporation of volatile dopants. The motivation of the study was to clarify the quantitative relationship between simple process parameters such as the flow rate of source gases and resulting chemical composition of sintered film. Hence, the compositional analysis of silica soot by FTIR(Fourier Transformation Infrared Spectroscopy) and ICP-AES(Inductively Coupled Plasma-Atomic Emission Spectrometry) under the control of the amount of dopant was carried out to obtain the quantitative composition. By measuring spectrum of absorbance from FTIR, the compositional change of B-O, Si-O, OH($H_2O$) in silica film was measured. The concentrations of these dopants were also measured by ICP-AES, which were compared with the FTIR result. The final quantitative relationship between simple process parameters and composition was deduced from the comparison between two results.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2560-2564
• /
• 2011

Mesoporous silicon dioxide (meso-$SiO_2$) was prepared using cetyltrimethylammonium bromide as the structure-directing reagent and tetraethyl orthosicate as the silicon source. The influence of pH value on the adsorption behavior of bisphenol A (BPA) was investigated. The adsorption capacity of BPA onto meso-$SiO_2$ increases slightly with pH value from 2 to 6, and then gradually decreases as further improving pH value. The effect of temperature was also studied, and the adsorption capacity of BPA gradually declines with increasing temperature. The adsorption kinetics and thermodynamics of BPA were examined. It is found that the adsorption of BPA onto meso-$SiO_2$ is in good agreement with Langmuir adsorption model. The rate constant of adsorption is $5.17{\times}10^{-3}g\;mg^{-1}\;min^{-1}$, and the maximum adsorption capacity is as high as 353.4 $mg\;g^{-1}$ at 20 $^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.238-239
• /
• 2011

최근 반도체 산업은 더 높은 성능의 회로 제작을 통해 초고집적화를 추구하고 있다. 이를 위해서 회로 설계의 최소 선폭과 소자 크기는 지속적으로 감소하고 있고 이를 위한 배선 기술들은 플라즈마 공정을 이용한 식각공정에 크게 의존하고 있다. 식각공정에 있어서 반응가스의 조성은 식각 속도와 선택도를 결정하는 중요한 요소이다. 본 연구에서는 CIS QMS (closed ion source quadrupole mass spectrometer)를 이용하여 CF4+Ar를 이용한 실리콘 산화막의 플라즈마 식각 공정 시 생성되는 라디칼과 이온 종들을 측정하였다. Ar 이온이 기판표면과 충돌하여 기판물질간의 결합을 깨놓으면, 반응성 기체 및 라디칼과의 반응성이 커져서 식각 속도를 향상 시키게 된다. 본 실험에서는 2 MHz의 RPS (remote plasma source)를 이용하여 플라즈마를 발생시키고 13.56 MHz의 rf 전력을 기판에 인가하여 식각할 웨이퍼에 바이어스 전압을 유도하였다. CF4/(CF4+Ar)의 가스 혼합비가 커질수록 식각 부산물인 SiF3의 양은 증가 하였으며, CF4 혼합비가 0일 때(Ar 100%) 비하여 1일 때(CF4 100%) SiF3의 QMS 이온 전류는 106배 증가하였다. 이때의 Si와 결합하여 SiF3를 형성하는 F라디칼의 소모는 0.5배로 감소하였다. 또한 RPS power가 800 W일 때 플라즈마에 의해서 CF4는 CF3, CF2, CF로 해리 되며 SiO2 식각 시 라디칼의 직접적인 식각과 Si_F2의 흡착에 관여되는 F라디칼의 양은 CF3 대비 7%로 검출되었고, 식각 부산물인 SiF3는 13%로 측정되었다. Ar의 혼합비를 0 %에서 100%까지 증가시켜 가면서 측정한 결과 F/CF3는 $1.0{\times}105$에서 $2.8{\times}102$로 변화하였다. SiF3/CF3는 1.8에서 6.3으로 증가하여 Ar을 25% 이상 혼합하는 것은 이온 충돌 효과에 의한 식각 속도의 증진 기대와는 반대로 작용하는 것으로 판단된다.

• Corrosion Science and Technology
• /
• v.2 no.5
• /
• pp.238-242
• /
• 2003

The characteristics of Ru etching using $O_2/Cl_2$ plasmas were investigated by employing inductively coupled plasma (ICP) etcher. The changes of Ru etch rate, Ru to $SiO_2$ etch selectivity and Ru electrode etching slope with the gas flow ratio, bias power, total gas flow rate, and source power were scrutinized. A high etching slope (${\sim}86^{\circ}$) and a smooth surface after etching was attained using $O_2/Cl_2$ inductively coupled plasma.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.148-152
• /
• 1999

the low temperature magnetoresistance effect, electron mobilities, and 2 Dimensional electron Gases (2DEG) properties were investigated in $Si/Si_{1-x}Ge_x$ quantum well devices. N-type $Si/Si_{1-x}Ge_x$ structures were fabricated by utilizing a gas source Molecular Beam Epitaxy (GSMBE). Thermal oxidation was carried out in a dry O atmosphere at $700^{\circ}C$ for 7 hours. Electron mobilities were measured by using a Hall effect and a magnetoresistant effect at low temperatures down to 0.4K. Pronounced Shubnikov-de Haas (SdH) oscillations were observed at a low temperature showing two dimensional electron gases (2DEG) in s tensile strained Si quantum well. The electron sheet density (ns) of $1.5\times10^{12}[\textrm{cm}^{-2}]$ and corresponding electron mobility of 14200 $[\textrm{cm}^2V^{-1}s^{-1}]$ were obtained at a low temperature of 0.4K from $Si/Si_{1-x}Ge_x$ structures with thermally grown oxides.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.134-134
• /
• 2011

High-k dielectric materials such as $HfO_2$, $ZrO_2$ and $Al_2O_3$ increase gate capacitance and reduce gate leakage current in MOSFET structures. This behavior suggests that high-k materials will be promise candidates to substitute as a tunnel barrier. Furthermore, stack structure of low-k and high-k tunnel barrier named variable oxide thickness (VARIOT) is more efficient.[1] In this study, we fabricated the $WSi_2$ nanocrystals nonvolatile memory device with $SiO_2/HfO_2/Al_2O_3$ tunnel layer. The $WSi_2$ nano-floating gate capacitors were fabricated on p-type Si (100) wafers. After wafer cleaning, the phosphorus in-situ doped poly-Si layer with a thickness of 100 nm was deposited on isolated active region to confine source and drain. Then, on the gate region defined by using reactive ion etching, the barrier engineered multi-stack tunnel layers of $SiO_2/HfO_2/Al_2O_3$ (2 nm/1 nm/3 nm) were deposited the gate region on Si substrate by using atomic layer deposition. To fabricate $WSi_2$ nanocrystals, the ultrathin $WSi_2$ film with a thickness of 3-4 nm was deposited on the multi-stack tunnel layer by using direct current magnetron sputtering system [2]. Subsequently, the first post annealing process was carried out at $900^{\circ}C$ for 1 min by using rapid thermal annealing system in nitrogen gas ambient. The 15-nm-thick $SiO_2$ control layer was deposited by using ultra-high vacuum magnetron sputtering. For $SiO_2$ layer density, the second post annealing process was carried out at $900^{\circ}C$ for 30 seconds by using rapid thermal annealing system in nitrogen gas ambient. The aluminum gate electrodes of 200-nm thickness were formed by thermal evaporation. The electrical properties of devices were measured by using a HP 4156A precision semiconductor parameter analyzer with HP 41501A pulse generator, an Agillent 81104A 80MHz pulse/pattern generator and an Agillent E5250A low leakage switch mainframe. We will discuss the electrical properties for application next generation non-volatile memory device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.4
• /
• pp.304-308
• /
• 2012

Transparent thin film transistors (TTFT) were fabricated using the rf magnetron sputtered ZnO-$SnO_2$ films as active layers. A ceramic target whose Zn atomic ratio to Sn is 2:1 was employed for the deposition of ZnO-$SnO_2$ films. To study the post-annealing effects on the properties of TTFT, ZnO-$SnO_2$ films were annealed at $200^{\circ}C$ or $400^{\circ}C$ for 5 min before In deposition for source and drain electrodes. Oxygen was added into chamber during sputtering to raise the resistivity of ZnO-$SnO_2$ films. The effects of oxygen addition on the properties of TTFT were also investigated. 100 nm $Si_3N_4$ film grown on 100 nm $SiO_2$ film was used as gate dielectrics. The mobility, $I_{on}/I_{off}$, interface state density etc. were obtained from the transfer characteristics of ZnO-$SnO_2$ TTFTs.

• Korean Journal of Materials Research
• /
• v.29 no.7
• /
• pp.456-462
• /
• 2019

ZnO thin-films are grown on a p-Si(111) substrate by RF sputtering. The effects of growth temperature and $O_2$ mixture ratio on the ZnO films are investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and room-temperature photoluminescence (PL) measurements. All the grown ZnO thin films show a strong preferred orientation along the c-axis, with an intense ultraviolet emission centered at 377 nm. However, when $O_2$ is mixed with the sputtering gas, the half width at half maximum (FWHM) of the XRD peak increases and the deep-level defect-related emission PL band becomes pronounced. In addition, an n-ZnO/p-Si heterojunction diode is fabricated by photolithographic processes and characterized using its current-voltage (I-V) characteristic curve and photoresponsivity. The fabricated n-ZnO/p-Si heterojunction diode exhibits typical rectifying I-V characteristics, with turn-on voltage of about 1.1 V and ideality factor of 1.7. The ratio of current density at ${\pm}3V$ of the reverse and forward bias voltage is about $5.8{\times}10^3$, which demonstrates the switching performance of the fabricated diode. The photoresponse of the diode under illumination of chopped with 40 Hz white light source shows fast response time and recovery time of 0.5 msec and 0.4 msec, respectively.

• Journal of the Korean Ceramic Society
• /
• v.15 no.4
• /
• pp.199-204
• /
• 1978

In the present investigation, refined alumina obtained from alunite locally available was used as a aluminous source to synthesize monocalcium aluminate $(CA)_3$ the major mineral constituent of alumina cement. The influence of $SiO_2$ and $Fe_2O_3$ contents on the formation of monocalcium aluminate was studied by X-ray diffraction analysis mainly. About 0.8-1.0 of $Al_2O_3/C_3O$ mol ratio and less than 4 percent of $SiO_2$ were desirable for the effective formation of CA. The small amount of alkali and sulphur contents contained in refined alumina from alunite as the impurities were affected to form $C_4A_3S$ and $C_3S_2$, disadvantageous compounds for the alumina cement, therefore the impurities should be restricted in minimum content as possible.