• 소성∙가공
• /
• 제8권5호
• /
• pp.482-490
• /
• 1999

7000 series Al alloy with good mechanical properties has been focused with tendency to reduce the components weight of aircraft and automobile. However, it is difficult to manufacture a sound extruded product because of segregation, grain growth, casting defect, surface defect, decreasing extrudability and so on. The objective of this study is to manufacture a new 7000 al alloy more than the extrudability of A7N01 and A7003 through controlling the weight (%) Mg, Zn, Si. Hot extrusion experiments on the axisymmetric rod are performed in 500℃ and also performed analysis of the same process using unmerical analysis method, a coupled rigid-thermoviscoplastic finite element method. Extrusion limit diagram was obtained for the developed alloy by FE-simulation in order to define the relationship of extrusion speed and initial billet temperature.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.336-340
• /
• 2014

The noise and vibration have been evaluated by using the finite element model in the vehicle developing stage. The sound pressure of the vehicle compartment is predicted by the acoustic cavity model coupled with the body structure. In general, the structural model has been focused to study in the improvement of the noise. It is not easy to treat the structural model, instead the acoustic cavity model is relatively simple and aids in root cause analysis of vibro-acoustic issues. Therefore, the acoustic transfer function of the cavity is more efficient for finding out the main contribution parts of the vehicle booming noise. And examples about the run-up booming noise demonstrate the validity of the AFT analysis for improving the vibro-acoustic sensitivity.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.701-708
• /
• 1997

A direct boundary element method(DBEM) is developed for thin bodies whose surfaces are rigid or compliant. Th eHelmholtz integral equation and its normal derivative integral equation are adopted simultaneously to calculate the pressure on both sides of the thin body, instead of the jump values across it, to account for the different surface conditions of each side. Unlike the usual assumption, the normal velocity is assumed to be discontinuous across the thin body. In this approach, only the neutral surface of the thin body has to be discontinuous across the thin body. In this approach, only the neural surface of the thin body has to be discretized. The method is validated by comparison with analytic and/or numerical results for acoustic scattering and radiation from several surface conditions of the thin body; the surfaces are rigid when stationary or vibrating, and part of the interior surface is lined with a sound-absorbing material.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.141-150
• /
• 1998

The measurement of strains in stamped sheet metal is essential to the design and manufacture of sound sheet metal products. The measured strains can also be used in verifying the reliability of the computer analysis such as finite element analysis. In most engineering applications, strains are measured from the deformed square grids or deformed circular grids in comparison with the initial undeformed grids. In such a case, however, strains are averaged in each grid and the localized strain in a region smaller than a grid size can not be measured. In the present study, the B-spline surface interpolation technique is introduced in order to measure the strains more exactly and effectively. The strains calculated by using the surface interpolation technique are compared with the strains calculated from the three-noded grids as well as with the finite element analysis.

• 대한기계학회논문집
• /
• 제17권12호
• /
• pp.2970-2981
• /
• 1993

In hot closed-die forging the load increases rapidly near the final stage. Preforming operation is important to both the sound final forging and die-service life. In this study, the material flows during preforming and final forging are investigated. The physical modeling with Plasticine as a model material showed clear flow patterns. The forging process were numerically simulated by the finite element method with the isothermal and the non-isothermal models. The flow patten of the isothermal simulation showed good agreements with the experiments. Temperature changes and pressure distributions on the die surfaces during one cycle of the forging process were obtained from the non-isothermal simulation. High pressure and temperature were developed at certain areas of the die surfaces. It was concluded that those areas usually coincide with each other and should be distributed by the preforming operations to enhance the die life.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.2805-2816
• /
• 1994

This paper describes dynamic finite element analyses performed to study the dynamic behaviors of a shipping container under the impact onto rigid target due to the accidental fall from the hight of 9 m. Using two and three dimensional techniques, the shipping container which gave the maximum damage, ten different drop orientations are considered ; at intervals of $5^{\circ}$ from $45^{\circ}$ to $90^{\circ}$ According to the present results, the orientation of the shipping container which gave the maximum damage is $85^{\circ}$ from horizontal for oblique drop in the primary impact. In the optimal design of the shipping container, the impact limiter material must be considered importantly because it's proper selection affects the weight and the manufacturing cost of the shipping container. The analysis of the shipping container in this paper demonstrated that the shipping container is structurally sound relative to the regulatory drop test requirements.

• 대한조선학회논문집
• /
• 제41권2호
• /
• pp.21-32
• /
• 2004

The non-cavitating noise of underwater propeller is considered numerically in this study. The main purpose is to analyze non-cavitating noise from underwater propellers in various operating conditions with different configurations. Noise is predicted by using time-domain acoustic analogy, boundary element method, and computational hydro-acoustics. The flow field is analyzed with potential-based panel method, and then time-dependant pressure data are used as the input for Focus Williams-Hawkings formulation to predict far field acoustics. Furthermore, boundary element method and computational hydro-acoustics are also considered to investigate duct propeller and ducted multi-stage propeller to consider the reflection and diffraction of sound waves. With this methodology, noise intensity and directivity of each noise sources could be well analyzed.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2002년도 하계학술발표대회 논문집 제21권 1호
• /
• pp.465-468
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the change of the modal frequencies was examined with the variation of the tuning fork length and width. Analytical model equations were derived from the numerically relating results of the modal frequency-tuning fork length by approximating minimization. Finally the BEM was used for the sound pressure field calculation from the structural displacement data.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 추계학술대회논문집; 한국과학기술회관, 8 Nov. 1996
• /
• pp.153-159
• /
• 1996

The acoustic characteristics of a direct radiator type loudspeaker has been studied in this paper. The vibration displacement of the speaker cone paper obtained by the finite element analysis has been converted into the vibration velocity and used as a boundary condition for the acoustic analysis. The frequency characteristics and the sound pressure distribution of the loudspeaker resulted from the radiation of the cone vibration have been calculated by the boundary element analysis. The numerical results have been verified by experiments carried out in an anechoic chamber. The variations of the acoustic characteristics due to the changes of some design parameters have been examined using the numerical model.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 1998년도 춘계종합학술대회
• /
• pp.394-399
• /
• 1998

This paper describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a hydrophone. The particular structure considered is a flooded piezoelectric spherical shell. The hydrophone is three-dimensionally simulated to transduce an incident plane acoustic pressure onto the outer surface of the sonar spherical shell to electrical potentials on inner and outer surfaces of the shell. The acoustic field formed from the scattered sound pressure is also simulated. And the displacement of the shell caused by the externally incident acosutic pressure is shown in temporal motion. The coupled FE-BE method is described in detail.