• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제24회 KOSCO SYMPOSIUM 논문집
• /
• pp.179-184
• /
• 2002

Interaction between flames and non-thermal plasmas of DBD type has been experimentally investigated. Vigorous streamers were observed under flame conditions because of the increase of reduced field (electrical) at high temperature as well as the seeding of free electrons and ions generated inside the flame. Flame lengths were significantly shortened as the applied voltage increased on account of intense mixing by ionic winds and soot-induced flows. Flame luminosities severely decreased under plasma conditions, which means the reduction of soot, since the residence time was reduced because of the flame shortening. Temperature and major species concentrations measured by FTIR were not changed despite the plasma generation. which shows overall chemistries were not affected by non-thermal plasmas.

• 한국수소및신에너지학회논문집
• /
• 제22권5호
• /
• pp.686-698
• /
• 2011

Mathematical models for char-slag interaction and near-wall particle segregation developed by Montagnaro et. al. were applied to predict various aspects of coal gasification in an up-flow entrained gasifier of commercial scale. For this purpose, some computer simulations were performed using gPROMS as the numerical solver. Typical design parameters and operating conditions of the commercial gasifiers were used as input values for the simulation. Development of a densely dispersed phase of solid carbon was found to have a critical effect on both carbon conversion and ash flow behavior. In general, such a slow-moving phase was turned out to enhance carbon conversion by lengthening the residence time of char or soot particles. Furthermore, it was also found that guiding the transfer of char or soot into the closer part of the wall to coal burner is favorable in terms of gasification efficiency and vitrified ash collection. Finally, to a certain degree densely dispersed phase of carbon showed an yield-enhancing effect of syngas.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.292-299
• /
• 2004

This study is intended to check a temperature of the flame to raise by burning A heavy oil in a boiler. to measure the concentration of DS and SOF after collecting the PM(Particulate Matters). and to analyze the components ingredients of SOF by G.C Mass for presupposing the generation of particulate matters(soot). It is thought that the methyl(CH3) of the cyclic compound is changed to the materials of 2 cycles and 3 cycles after becoming CH by dehydrogenation and also mixing with the CH of a chain compound. form H-$\cdot$C=C$\cdot$-H that is mentioned before. in order to become Polycyclic Aromatic Hydrocarbon.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.255-258
• /
• 2002

Liquid rocket engines using liquefied natural gas (LNG) or methane as a fuel is known to have several good characteristics, such as high specific impulse compared to other hydrocarbon fuels, environment-friendly exhaust gas, low production cost, and re-usability with low soot generation in the cooling channel. In this study, experimental combustion chambers capable of using LNC and $CH_{4}$ are being researched through experimental firing tests, and within easy range of eyes' inspection, there are the periodical existence of soot or discoloration in the chamber wall surface. This result means that mixture ratio of oxidizer and fuel fluctuates periodically between outer-row injectors in the mixing head in the circumferential direction. Therefore, based on this phenomenon, the variation of mixture ratio near the chamber wall caused by the spill pattern of a shear coaxial injector was analyzed quantitatively and the thermal heat flux Into the cooling channel is modified. Then, the calculated and modified results are compared with the measured ones.

• 반도체디스플레이기술학회지
• /
• 제12권4호
• /
• pp.45-48
• /
• 2013

The electronic device, such as flat panel display (FPD), is very important in our life as a means of communication between humans. Liquid crystal display (LCD), which is categorized as a flat panel display, has been used in many display products, especially in TV industry. An LED TV is composed of several electrical components, such as liquid critical module (LCM), analog to digital convertor (AD), power supplier, and inverter board. These modules are very vulnerable to particulate contamination, and causing malfunction or visibility degradation. In this study, we developed a test method for prediction of LCM's lifetime. The test system consists of carbon particle generation flame, dilution system, test chamber, and particle concentration monitoring instrument. Since the carbon particles are the most abundant in the atmosphere and easily absorb light, soot particles are used as a challenging material for this test. The concentration of generated soot particles is set around 4,000,000 #/cc, which is 400 times higher than that of usual atmospheric particles. Through this experiment, we deduced the relationship between the dust concentration and life time of the test specimen.

• 한국분무공학회지
• /
• 제21권1호
• /
• pp.29-36
• /
• 2016

The effect of high ambient temperature and pressure conditions on the combustion performance of n-butanol, n-heptane and its mixing fuel (BH 20) were studied in this work. To reveal this, the closed homogeneous reactor model applied and 1000-1200 K of the initial temperature, 20-30 atm of initial pressure and 1.0 of equivalence ratio were set to numerical analysis. It was found that the results of combustion temperature was increased and the ignition delay was decreased when the ambient conditions were elevated since the combustion reactivity increased at the high ambient conditions. On the contrary, under the low combustion temperature condition, the combustion pressure was more influenced by the ambient temperature in the same ambient conditions. In addition, the total mass and the mass density of tested fuels were influenced by the ambient pressure and temperature. Also, soot generation of mixing fuel was decreased than n-heptane fuel due to the oxygen content of n-butanol fuel.

• 전기학회논문지
• /
• 제65권6호
• /
• pp.1001-1006
• /
• 2016

As consumption of energy is increasing rapidly, energy saving is emphasized in nowadays. Thermal power plant occupies a large proportion in various type of power plant. Major causes of decreased power generation efficiency on thermal power stations is deposition of fly ash. Soot Blower is a facility to remove the ash which is deposited outside of tube by steam blowing on boiler. Residual stream which caused by lance tube in soot blower cannot be discharged steam effectively in lance tube causes reducing the thickness of lance tube. On the contrary, increasing discharge ratio of steam, lance tube cannot sustain proper pressure to remove ash on tube. This study suggests increasing discharge ratio of steam with proper pressure to remove ash on tube by optimization on shape of lance tube nozzle. To optimize shape of nozzle, discharge ratio and maximum blowing pressure on nozzle is selected as object functions. Diameter of nozzle, distance between nozzles, angle of nozzle and gap between nozzle is selected as design parameters. Then the design of experiment (DOE) with an orthogonal array is performed to analyze the effect of design parameters. And grey relational analysis and analysis of mean (ANOM) is performed to optimize shape of lance tube.

• 공업화학
• /
• 제20권4호
• /
• pp.355-362
• /
• 2009

석유를 기반으로 한 연료는 가까운 미래에 고갈될 것이다. 디메틸에테르(Di-methyl Ether, DME)는 청정에너지이며 천연가스,석탄 및 바이오매스 등으로 생산이 가능하다.DME는 분자구조 내에 탄소-탄소 결합이 없는 함산소 연료로 연소시 그을음과 황산화물을 발생하지 않으며, 물리적 특성이 액화석유가스(Liquified Petroleum Gas, LPG)와 매우 유사하여 LPG 유통인프라를 그대로 활용할 수 있다. DME는 세탄값이 55~60 정도로 높아 디젤 자동차용 연료로도 활용이 가능하다.차세대 청정연료로 혹은 차세대 화학공업 원료물질로 전력생산,디젤 연료, 가정용 연료 및 연료전지 등에 사용이 가능하다.본 총설에서는DME의 특성, 표준화, 국내외의 기술개발현황, 대체연료로서의 활용에 대해 살펴보고자 한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.364-370
• /
• 2008

Spinning detonations propagating in a circular tube were numerically investigated with a one-step irreversible reaction model governed by Arrhenius kinetics. The time evolution of the simulation results was utilized to reveal the propagation mechanism of single-headed spinning detonation. The track angle of soot record on the tube wall was numerically reproduced with various levels of activation energy, and the simulated unique angle was the same as that of the previous reports. The maximum pressure histories of the shock front on the tube wall showed stable and unstable pitch modes for the lower and higher activation energies, respectively. The shock front shapes and the pressure profiles on the tube wall clarified the mechanisms of two modes. The maximum pressure history in the stable pitch remained nearly constant, and the single Mach leg existing on the shock front rotated at a constant speed. The high and low frequency pressure oscillations appeared in the unstable pitch due to the generation and decay of complex Mach interaction on the shock front shape. The high frequency oscillation was self-induced because the intensity of the transverse wave was changed during propagation in one cycle. The high frequency behavior was not always the same for each cycle, and therefore the low frequency oscillation was also induced in the pressure history.

• 한국분무공학회지
• /
• 제28권1호
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.