• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.896-902
• /
• 2009

EGR is applied in order to lower temperature of combustion chamber by using the specific heat of carbon dioxide in engine exhaust gas. However, the problem of EGR system in diesel engine is high PM concentration. Combined EGR system can be reduced it by mixing exhaust gas of gas engine into the intake air of diesel engine. This experimental study was designed for EGR system for both engines use. The results of EGR experimental study by using diesel engine and gas engine are as follows. 1) The pressure of combustion and rate of heat release decreased. 2) The specific fuel consumption increased. But, up to middle load, it little increased. 3) NO concentration has decreased up to 50% in almost all combustion area. 4) The variation of the PM concentration at low load is not so seen. But at high load, PM increased rapidly when concentration of oxygen is decreased and most of it caused the increasing of Dry Soot.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.508-516
• /
• 1989

The objective of this study is to investigate on the pulsating combustion of a granular coal in a Rijke type pulse combustor. The combustor is made of a 120cm long pipe with a honeycomb as a fire grate in the lower half. A fixed amount of coal is laid on the honeycomb and burned downward after ignition by using propane gas. Then the combustion driven acoustic oscillation occurs and makes the combustion pulsate with a very high amplitude. The effect of the pulsation and the air flow rate on the combustion characteristics is examined in comparison with the normal combustion. The non-pulsating combustion is made possible by placing absorbing material under the honeycomb. The combustion phenomena are observed visually, the burning time is measured in order to evaluate the combustion rate, and the variation of the gas temperatures is recorded. It is found that the fuel particle is greatly agitated like boiling by the flow pulsation and the burning-down velocity is so fast that the fuel is burned almost simultaneously. The combustion rate can be increased as twice as that of non-pulsating combustion with increase of the air flow rate. And the combustion becomes clean with less soot deposit and emission.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.6
• /
• pp.614-621
• /
• 2020

Recently, as the fine dust is increased and the emission regulations of diesel engines are strengthened, interest in diesel soot filtration devices is rapidly increased. In particular, there is a demand for technology development for higher efficiency of diesel exhaust gas after-treatment devices. As part of this, many studies conducted to increase the exhaust gas treatment efficiency by improving the flow uniformity of the exhaust gas in the DPF and reducing the pressure drop between the inlet and outlet of disel particle filter (DPF). In this study, computational fluid dynamics (CFD) simulation was performed when exhaust gas flows into the canning reduction device equipped with a 13" asymmetric DPF in order to maintain the flow uniformity in the diesel exhaust system and reduce the pressure. In particular, a study was conducted to find the geometry with the smallest pressure drop and the highest flow uniformity by simulating the DPF I/O ratio, exhaust gas temperature, inlet-outlet pressure and flow uniformity according to the geometry and hole size of distributor.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.5
• /
• pp.518-524
• /
• 2013

In this study, we conducted a study on characteristics of exhaust gas emissions from boiler when water-bunker oil mixed by homogenizer was burned in boiler. The results showed that NOx concentration and CO concentration of the homogenized bunker oil was decreased by 19% and 54% compared to pure bunker oil pretreatment was not being performed. And, in the case of water-bunker A oil, the NOx concentration was decreased with increasing water mixing ratio in bunker A oil. In particular, the NOx concentration in exhaust gas of 20 %water-80 %bunker A oil decrease by 45 % compared with pure bunker-A. However, the CO concentration in exhaust gas of 20 %water-80 %bunker A oil shows irregular changes. This means that the mixing of water more than a certain amount can cause a decrease in combustion performance. From this result, it can be found that critical mixing ratio of water in bunker A oil for normal combustion is 15% in this study. Deposition amount of soot that is collected in the vicinity of the chimney was decreased with increasing water mixing ratio.

• Resources Recycling
• /
• v.8 no.5
• /
• pp.34-43
• /
• 1999

An elecmc arc cracking reaclor is developed for the productiol~o f ieusuble fuel gas by the thennal destruction of waste oil. The churaclensucs of product gas and ~esiduesf rom arc crachng of wnste lubr~cat~nogil are sludird. Thc product gas is mainly coruposcd of hydrogen 135-4076), acetylene (13-4076), ethylene 13-476) and olher hgdrocnrbons. The contenr of carbon monomde, one or the main product in a conventional low-temperature Lhennal cracking umt, 1s very slnvll in lhis atc cracking expcnmcnt. Total calocctic wlue of product gas shows 11,000-13.000 kcizlkg, which is hiph cnough to use as a ~ L I I I Cga~ s . and the concentralions oC loxic gases arc well below the rcguliltury emission critena The GCIMS analysis of llquld-phase residues shows that the high rnalccular welgllt hydrocilrbons in the waste oil arc cracked into the low malecular weight hydrocarbons snd hydroem,. The dehydrogcnntion is found lo be Lhe main cracking rcacuon due lo the high temperalure ~ ~ ~ d ubcyc edle ctric arc. The average parucle size of soot as the solid-phase residue is 10 3 wm, and the conlents of cabon a ~ hdea vy metals are abovc 60% and under 0.01 ppm, respecttrely. Thc utllizvtion or sool, as industl-id1 rcsource seems lo he reasible aIter refimng.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.196-205
• /
• 2016

The exhaust gas discharged by cars not only threatens the health of the human body, but also contributes to global warming, due to the resulting increase in the concentrations of ozone, fine dust and carbon dioxide. Therefore, the government has steadily implemented careful inspection systems for exhaust emissions, in order to efficiently regulate the exhaust gas of cars. Studies on reducing the exhaust emissions of automobiles have been conducted in various fields, including ones designed to reduce the generation of HC, NOx, and $CO_2$ in the exhaust emission of vehicles. However, there have been insufficient studies on the reduction of the exhaust emission for old diesel vehicles. To develop careful inspection systems for the exhaust emissions of old diesel vehicles, studies on the reduction of the exhaust emissions and improvement of power are necessary by cleaning the carbon sediment in both the intake manifold and injector. Therefore, in this study, we analyzed and compared the amounts of gas emitted when simultaneously cleaning or not cleaning the intake manifold and injector of diesel automobiles with mileages over 80,000 km and operating periods over 5 years. The experimental results showed that in the case where the intake manifold and injector were simultaneously cleaned, there was a decline of 75.2% in the gas emission compared to the cases where only the manifold or injector is cleaned. Also, it was found that simultaneously cleansing the intake manifold and injector enabled the exhaust standard to be satisfied for less than 30% within 8.5 sec.

• Advances in aircraft and spacecraft science
• /
• v.1 no.3
• /
• pp.311-330
• /
• 2014

Environmental impact of aircraft emissions can be addressed in two ways. Air quality impact occurs during landings and takeoffs while in-flight impact during climbs and cruises influences climate change, ozone and UV-radiation. The aim of this paper is to investigate airports related local emissions and fuel consumption (FC). It gives flight path optimization model linked to a dispersion model as well as numerical methods. Operational factors are considered and the cost function integrates objectives taking into account FC and induced pollutant concentrations. We have compared pollutants emitted and their reduction during LTO cycles, optimized flight path and with analysis by Dopelheuer. Pollutants appearing from incomplete and complete combustion processes have been discussed. Because of calculation difficulties, no assessment has been made for the soot, $H_2O$ and $PM_{2.5}$. In addition, because of the low reliability of models quantifying pollutant emissions of the APU, an empirical evaluation has been done. This is based on Benson's fuel flow method. A new model, giving FC and predicting the in-flight emissions, has been developed. It fits with the Boeing FC model. We confirm that FC can be reduced by 3% for takeoffs and 27% for landings. This contributes to analyze the intelligent fuel gauge computing the in-flight fuel flow. Further research is needed to define the role of $NO_x$ which is emitted during the combustion process derived from the ambient air, not the fuel. Models are needed for analyzing the effects of fleet composition and engine combinations on emission factors and fuel flow assessment.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.4
• /
• pp.351-358
• /
• 2015

In the recent times, the use of gasoline direct injection (GDI) engines has been regarded as a means of enhancing conformance to emission regulations and improving fuel efficiency. GDI engines have been widely adopted in the recent years for their better engine performance and fuel economy compared to those of conventional MPI gasoline engines. However, they present some disadvantages related to the mass and quantity of particulate matter generated during their use. This study investigated the nanoparticle characteristics of the particulate matter exhausted from a GDI engine vehicle installed with different types of gasoline particulate filters, after subjecting it to ultra-lean burn driving conditions. Three metal foam and metal fiber filters were used for each experimental condition. The number concentrations of particles were analyzed for understanding their behavior, and the reduction characteristics were obtained for each type of filter.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.603-608
• /
• 2012

Recently we have a growing interest in environmental pollution and alternative energy. Diesel engine is generally used to produce the power on shore and sea. However, the combustion characteristics and exhaust emissions of the engine are changed on account of the wear of fuel system and the altered ambient condition of the combustion chamber by the increment of the engine operation hour. Therefore the combustion characteristics and exhaust emissions on the fuel injection timing were experimentally investigated to find out the optimum fuel injection timing in case of the about 20 years used diesel engine using biodiesel blend oil. The original fuel injection timing of the engine is BTDC $22^{\circ}$ CA. However, it is found that the optimum fuel injection as a result of analyzing the specific oil consumption and exhaust emissions of 20 years used the engine is BTDC $26^{\circ}$ CA.