• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.249-252
• /
• 1997

Highly oriented ZnO thin films were fabricated by dip-coating technique using zinc acetate 2-methoxyethanol 2-aminoethanol solution as starting materials, and effects of substrates on the film's orientation were investigated. Product films were obtained by prefiring at 300, 400, 500 and 550℃ for 10 min, followed by final heat-treatment at the same temperatures as prefiring for 1h. c-axis oriented films on glass substrates were prepared by heat treatment of prefiring films at 300-550℃, while films on alumina showed polycrystalline structure. Films with c-axis orientation exhibited lower specific resistivities than those of polycrystalline films with partial crack and pore.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.43-48
• /
• 2003

The problem of welding stresses and fatigue behavior is the main concerns of welding research fields. The residual stresses and distortion of structures by welding is exert negative effect on the safety of mechanical structures. That is, expansion of material by high temperature and distortion by cooling during welding process is caused of tensile and compressive residual stresses on welding material, and this residual stresses reduce fracture and fatigue strength of welding structures. The accurate prediction of residual stress and relaxation due to loading and post weld heat treatment of weld zone is very important to improve the quality of weldment. In this study, a finite element modeling technique is developed to simulate the relaxation of residual stresses due to loading and post weld heat treatment of weld zone. The accuracy of finite element models is evaluated based on experimental results and the results of the analytical solution.

• 열처리공학회지
• /
• 제9권2호
• /
• pp.91-102
• /
• 1996

Microstructural control to produce multiphase structure has received much attention to improve the high temperature strength as well as low temperature ductility of intermetallics. Transmission electron microscopic investigation has been carried out concerning the effect of Cr-precipitation on the mechanical properties of B2-ordered NiAl containing 4 to 8 mol% of Cr. By aging at temperatures around 973 K after solution annealing, fine spherical precipitates took place homogeneously in the NiAl matrix and the alloys hardened appreciably. Selected area electron diffraction (SAED) patterns have not revealed any additional extra-spots during aging, because the Cr-particles show cube-cube orientation relationship and keep a perfect coherency with the ordered matrix lattice. Dislocations were confirmed to bypass the particles during deformation. Although the dispersion of Cr-particles increased the yield strength of NiAl at intermediate temperature, the strength decreased appreciably at higher temperatures.

• 한국수산과학회지
• /
• 제28권6호
• /
• pp.728-735
• /
• 1995

The peptidyl prolyl cis-trans isomerase(PPlase, EC 5.2.2.8) from Bacillus stearothermophilus SIC1 was extracted from the cells treated with by lysozyme. PPlase was purified from the cell extracts by heat treatment, ammonium sulfate precipitation, ion exchange chromatography and finally gel filtration (FPLC). The purity of purified the enzyme after Superose 12 column chromatography was examined by sodium dodecyl sulfate polyacrylamide gel electrophoresis(SDS-PAGE). The molecular weight of the purified PPlase was estimated as 18,000 by SDS-PAGE. The 39 amino acid residues from the N-terminus were determined by the protein sequencer. The enzyme showed the optimum pH at 8.0 and was stable at the range of pH 7.0 to 8.0. The enzyme was considerably stable after heat treatment at $60^{\circ}C$ for 30 minutes, and the enzyme was quite stable up to $65^{\circ}C$. The presence of the PPlase in the refolding solution accelerated the isomerization rate of the assay peptide.

• 한국레이저가공학회지
• /
• 제14권1호
• /
• pp.25-29
• /
• 2011

Micromachining of photosensitive glass by UV exposure, heat treatment, and etching processes is reported. Like photoresist, the photosensitive glass is also classified into positive and negative types by development characteristics. For the positive type, the exposed area is crystallized and etched away during the etching process in HF solution, whereas the unexposed area is crystallized and etched away for the negative type. The crystallized area of the photosensitive glass has an etch rate approximately 30~100 times faster than that of the amorphous area so that it becomes possible to fabricate microstructures in the glass. Based on the unique properties of glass such as high optical transparency, electrical insulation, and chemical/thermal stability, the glass micromachining technique introduced in this work could be widely applied to various devices in the fields of electronics, bio engineering, nanoelectonics and so on.

• 한국세라믹학회지
• /
• 제26권4호
• /
• pp.471-478
• /
• 1989

In this study we investigated the gelation time of sol which containing mixtures of TEOS with H2O, ethanol, HCl in the preparation of monolithic silica glass through Sol-Gel method. In this case apparent activation energies were observed by Arrhenius equation. We investigated the conversion from gel to glass in drying and heat treatment stages using DT-TG, FT-IR, XRD analysis and dried gel conversed to glass by heat treatment up to 85$0^{\circ}C$. The results of this experiment showed that the gelation time of solutions were promoted when increasing the amount of addition of H2O and HCl catalyst for TEOS and high reaction temperature of solution.

• 전기의세계
• /
• 제28권9호
• /
• pp.43-50
• /
• 1979

Silicon nitride films were chemically deposited on silicon substrates by reacting SiCl$_{4}$ and NH$_{3}$ in a nitrogen atmosphere at 700~1100 .deg.C. The deposition rate increased rapidly with deposition temperature upto about 1000 .deg.C, and became less temperature dependent above this temperature. The etch rate of films in buffered HF solution decreased, with an increase of deposition temperature, and a heat treatment at a temperature higher than that of the deposition considerably reduced the etch rate. It indicates that the heat treatment resulted in a densification of the films. Surface charge density of 3~4 * 10$^{11}$ /cm$^{2}$ was determined from the C-V characteristics of MNS diode, and it was also found that surface charge density depended on deposition temperature, but not film thickness. The current-voltage characteristics displayed a logI-V$^{1}$2/ dependence in the temperature range of 300~500.deg.K. Measurement of the slope of this characteristics and its dependence on temperature and bias polarity suggest that conduction in sili con nitride films arises from the Poole-Frenkel mechanism.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.464-467
• /
• 1996

The microstructural evolution during mechanical alloying of Nb and Sn powders, of average composition Nb3Sn, has been investigated by X-ray diffraction(XRD) and scanning electron microscopy(SEM). Observations by SEM showed a progressive change of milling time. From the XRD studies, the structural development with milling time depends on the ball size for a given powder/ball ratio. Using a larger ball of 9.5mm diameter, the elemental powders initially alloy mechanically to form an A15 structure phase, and then amorphised with continued milling. However, in case of milling with a smaller ball of 3.968mm diameter, an amorphous phase is first formed. These results can be understood by considering the dependence of the milling energy on the ball size. The homogeneous stoichiometric $Nb_3Sn$ phase could be easily obtained by heat treatment of a supersaturated solid solution produced by MA. Heat treatment of an amorphous phase formed by MA resulted in the mixture of the $Nb_3Sn$ and $Nb_6Sn_5$ phases.

• 열처리공학회지
• /
• 제10권1호
• /
• pp.55-62
• /
• 1997

The morphology of deformation induced dislocations in polycrystalline $Ni_3$(Al, Cr) containing $M_{23}C_6$ precipitates has been investigated in terms of transmission electron microscopy(TEM). Fine Polyhedral precipitates of $M_{23}C_6$ appeared in the matrix by aging at temperatures around 973 K after solution annealing at 1423 K. TEM examination revealed that the $M_{23}C_6$ phase and the matrix lattices have a cube-cube orientation relationship and keep partial atomic matching at the {111} interface. After deformation at temperature below 973 K, typical Orowan loops were observed surrounding the $M_{23}C_6$ particles. At higher deformation temperatures, the Orowan loops disappeared and the morphology of dislocations at the particle-matrix interfaces suggested the existence of attractive interaction between dislocations and particles. The change of the interaction modes between dislocation and particles with increasing deformation temperature can be considered as a result of strain relaxation at the interface bet ween matrix and particles.

• 열처리공학회지
• /
• 제22권4호
• /
• pp.223-227
• /
• 2009

The feasibility of plasma electrolytic polishing technology of stainless steel was examined. The results show that austenitic stainless steel can be polished clearly using potentiostatic regimes with various concentration of ammonium sulfate ($(NH_4)_2SO_4$) solution above certain initial temperature. The equipment and deposition produces for polishing process are described and the effect of processing parameters on the characterizations polished-samples has been investigated.