• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.676-681
• /
• 1997

The purpose of this study is to evaluate the thermal Conductivity and Foolr Impact Sound of Polyurethane Concretes. The Polyurethane Concretes are prepared with various resin content, Fine and Coarse aggregates content, and its thickness, and tested for the Thermal Conductivity and Impact Sound. From the test results. the sound insulation grade of polyurethane concretes by the floor impact sound test on high frequency band is L-60, and its effect is considerable Polyurethane concretes have high degree of solidity compared with other heat shield materials, and its thermal conductivity is 0.05kcal/$mh^{\cire}C$. And it is suitable for sound proof floor materials.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.1 s.34
• /
• pp.19-24
• /
• 2006

Experiments are carried out to investigate the effect of radial tip clearance on a turbopump inducer, which has two blades with inlet tip blade angle of 7.8 degree and tip solidity of 2.7. Hydraulic and cavitation tests are performed for three cases of tip clearance ratio, that is, 0.026, 0.053, and 0.079. With increase in the tip clearance, inducer head and pressure on the inducer tip decrease. Attached cavitation and cavitation surge are observed in the cavitation tests. In the attached cavitation one cell rotates at the same rotational speed as that of the inducer. Cavitation performance deteriorates with increase in the tip clearance. The level of casing vibration increases in the cavitation condition and the level is very high when the attached cavitation appears.

• Journal of the Korean Home Economics Association
• /
• v.24 no.4
• /
• pp.139-146
• /
• 1986

The purpose of this study was to identify aesthetic concepts of‘Sarangbang’furniture during the Yi-dynasty period and aesthetic descriptions indicating each concept expressed by experts in traditional furniture. The furniture selected for the study includes desks, table bookcases, document and stationary boxes (mungab), letter holders (Kobi) and inkstone boxes (younsang) with lacquer and oil finish on. The respondents were 72 traditional furniture experts; researchers collectors, sellers and artists related to period furniture. The important points of aesthetic descriptors were collected 123 from related literature. From experts' answers, 47 representative descriptors were selected. Data were analyzed with the SPSS using frequency, Percentage mean, factor analysis, t-test and C2. The results were as follows; 1. The aesthetic concept of sarangbang furniture during the Yi-dynasty can be categorized into 9 aspects; appearance of beauty, stability the interior space, naturalness, nobleness/harmony of lines, detail/refinement, simplicity, diversity solidity and surface division. 2. The characteristics of the Korean traditional furniture can be described using 47 descriptors explaining 9 concepts mentioned above.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.212-219
• /
• 2004

The effect of frequency and amplitude of the OWC (Oscillating Water Column) motion on the nonlinear reaction forces in an air duct arc studied experimentally. Experimental OWC model is idealized as a simple circular cylinder with an orifice type air duct located at the middle of the top rid. Reaction forces due to forced heave oscillation are measured and analyzed. By subtracting the effect of inertia forces and restoring forces, pneumatic damping force and added spring force are deduced. The effects of the frequency and amplitude of the heave motion are discussed. Also, the effects of solidity of the duct on the reaction forces are discussed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.240-244
• /
• 2004

Characteristics of steady and unsteady cavitation in a turbopump inducer were investigated in this paper. To see the effect of tip clearance on the inducer performance, three cases of tip clearance were tested. The helical inducer, which has two blades with inlet tip blade angle of 7.8 degree and tip solidity of 2.7, was tested in the water. In the non-cavitating condition, the inducer head decreased with increase in the tip clearance. Rotating cavitation and cavitation surge were observed through unsteady pressure measurements at the inducer inlet. The cell number and propagation speed of the rotating cavitation were determined through cross-correlation analysis. During the rotating cavitation one cell rotated at the same rotational speed as that of the inducer rotation and the cavitation surge did not rotate. The critical cavitation number increased with increase in the tip clearance at the same flow rate, but the change of critical cavitation number was small at the nominal flow rate.

• Solar Energy
• /
• v.6 no.2
• /
• pp.86-92
• /
• 1986

This paper presents the aerodynamic performances of horizontal axis wind turbines with non-twisted but taperd blades. Five configurations of blades, namely, one straight blade and four tapered blades with taper ratio of ranging from 0.1 to 0.7 have been simulated. The aerodynamic performances of the wind turbines have been determined over blade incidence angle of ranging from $2^{\circ}$ to $6^{\circ}$ and keeping same solidity and radius of them. The results are presented comparing straight blade from four tapered blades for maximum power coefficient and tip looses against variation of taper ratio. It also shows that the wind turbine with taper ratio of 0.5 has the highest maximum power coefficient than others. And wind turbines with taper ratio below 0.2 have lower values of maximum power coefficients than straight one. The tip loss of straight blade is the largest and reduces Slightly with the decrementation of taper ratio.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.33-41
• /
• 2005

This paper describes the conceptual design of medium size helicopter rotor system. Based on assumed design requirements, trade-off study for rotor configuration has been conducted in terms of rotor tip speed, disk loading, blade area, solidity, etc for estimated primary mission gross weight. For the main rotor, four-blade and five-blade rotors are studied with the conventional tail rotor. The performance analysis for baseline configuration is conducted using a helicopter performance analysis program. The analysis shows design results satisfy the design requirements.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.1
• /
• pp.131-138
• /
• 2000

In this study, physical and engineering properties of ordinary portland cement and microcement were investigated to verify reinforcing effect of underpinning of open caisson foundation by using microcement grouting. Laboratory injection tests such as infiltration and injection in case of seepage for the stream bed soil at ${\bigcirc}{\bigcirc}$ Great Bridge in Seoul were carried out. Field injection tests to reinforce open caisson foundation at ${\bigcirc}{\bigcirc}$ Great Bridge were performed and the ability of application by microcement grouting was evaluated. From the test results, physical and engineering properties of microcement are better than those of ordinary portland cement. Also, the ability of infiltration and solidity in case of seepage is better than that of ordinary portland cement. Therefore, it is concluded that microcement is an excellent material to reinforce open caisson foundation of the existing bridge structure under the water and can be used as underpinning material of general foundations.

• Journal of Technologic Dentistry
• /
• v.7 no.1
• /
• pp.13-18
• /
• 1985

Casting alloys, both precious and non-precious, were by heat in order to observe the change in HB and the results were : 1. The hard treatment showed 1.4 - 1.5 times as high as the soft treatment in HB. 2. The experiment shows that Au-Pt should be contained more than 75% to prevent color change. 3. Cu by hard teatment played the greatect part in creasing the solidity of Ag-Cu alloy. 4. Casting Co-Cr alloys showed little difference of HB in heat treatment.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.4
• /
• pp.183-188
• /
• 2017

Block Chain is a technology that records and shares distributed ledgers without a central authority, providing a decentralized platform for transparent transactions in the business and enhancing transparency and traceability in all transactions to ensure trust in the transaction. Despite initial doubts about this technology, it is committed to adopting, adapting and improving the technology in a wide range of industries, including finance, government, security, logistics, food, medical, legal, and real estate. This study examines this technology, its applicability and potential benefits to the manufacturing supply chain. A tracking system of manufacturing supply chain to visualize transparency and traceability is implemented, and the conditions for adopting the technology in the manufacturing supply chain and the issues to be addressed are discussed.