• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.312-322
• /
• 2002

In this study, an innovative semi-solid die casting technology to replace heavier cast iron compressor parts with lightweight aluminum castings was proposed, and the application possibility for home-appliance component was investigated. The most important factors regarding the semi-solid die casting process are the reheating process of the raw materials to the semi-solid state, specifications of the forming machine, the optimal injection conditions and die design. Materials used in this study were A3S7 and hSn alloys fabricated by the electromagnetic stirring process. The optimal injection conditions for semi-solid die casting process were Presented with the reheating conditions of the semi-solid materials. To investigate the effect of plunger tip shape on the formability and mechanical properties in semi-solid die casting process for complicated shape part, two kinds of plunger tip shape with long and short plunger tip taper are proposed.

• Transactions of Materials Processing
• /
• v.5 no.3
• /
• pp.239-255
• /
• 1996

A new forming technology has been developed to fabricate near-net shape products using light metal. A semi-solid forming technology has some advantages compared with the conventional forming processes such as die casting squeeze casting and hot/cold forging. In this study the numerical analysis of semi-solid filling for a straight die shape and orifice die shape in gate pattern is studied on semi-solid materials(SSM) of solid fraction fs =30% in A356 aluminum alloy. The finite difference program of Navier-Stokes equation coupled with heat transfer and solidification has been developed to predict a filling pattern and the temperature distribution of SSM. The programdeveloped in this study gives die filling patterns of SSM and final solidifica-tion region.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.49-56
• /
• 2005

In the semi-solid die casting process, an important thing is the flow behavior of semi-solid materials. The flow patterns of the semi-solid material can make the defects during die filling. To control the flow patterns is very important and difficult. In this paper, the flow behavior of the semi-solid A356 alloy material during die filing at various die gate shapes has been observed with the grain size controlled material. The effect of the gate shape on the die filling characteristics was investigated. The filling tests in each plunger stroke were experimented, and also simulated on the semi-solid material die casting process by MAGMAsoft. According to the filling tests and computer simulation, the effect of the gate shape on liquid segregation has been investigated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.152-155
• /
• 2004

In the semi-solid die casting process, the important thing is the flow behaviors of semi-solid material. The flow patterns of semi-solid material can make the defects during die filling. To control of the flow patterns, is very important and difficult. In this paper, the flow behaviors of the semi-solid A356 alloy material during die filling at various die gate shapes has been observed with the grain size controlled material. The effects of the gate shape on the die filling characteristics were investigated. The filling tests in each plunger strokes were experimented, also simulated on the semi-solid material die casting process by MAGMAsofi. According to the filling tests and computer simulation, the effect of the gate shape on liquid segregation had been investigated.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.158-164
• /
• 1996

In this paper, the CNC cutting planning module for product with three dimensional solid shape is realized to develop a smart CAD/CAM system which performs systematically from the shape design of procuct by the B-Rep solid modeler to the CNC cutting of product by a machining center. The three dimensional solid shape of product can be easily designed and constructed by the Euler operators and Boolean operators of the solid modeler. And the various functions such as the automatic generation of tool path for the rough and finish cutting processes, the automatic elimination of overcut, the automatic generation of CNC code for the machining center and do on, are established. Especially, the overcut-free tool paths are obtained by splitting the CL solid which is composed of the offset surfaces of the solid shape of product.

• International Journal of CAD/CAM
• /
• v.11 no.1
• /
• pp.18-26
• /
• 2011

This paper proposes a new solid-shape modeling system based on a lusterware-image illustration. The proposed method reconstructs a three dimensional solid shape from a set of rough sketches that are typically drawn in the early stages of the design process. The sketches do not have to be strictly accurate, and this tolerance to the roughness of the input sketches is one of the major advantages of the proposed method. The proposed system creates an initial shape based on the silhouette of the input lusterware-images. Then the user can edit the initial shape with intuitive cutting and dishing-up operations, which are based on sketching user interface. To achieve the goal, the system retains the geometric model with two representations: a point-set data and a volume data. This dual data structure allows the program to create an initial shape from the input images with little computational cost, and the user can apply cutting and dishing-up operations without substantially increasing computational and memory requirements. In this research, we have tested the proposed system by reconstructing solid models of some mechanical parts from rough sketches. The experimental results indicate that the proposed method is useful for the prototyping of a solid shape.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.26-38
• /
• 2009

It was reported that the semi-solid forming process has many advantages over the conventional forming process, such as a long die life, good mechanical properties and energy savings. It is very important, however, to control liquid segregation to gain mechanical property improvement of materials. During forming process, rheology material has complex characteristics, thixotropic behavior. Also, difference of velocity between solid and liquid in the semi-solid state material makes a liquid segregation and specific stress variation. Therefore, it is difficult for a numerical simulation of the rheology process to be performed. General plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. The behavior and stress of solid particle in the rheology material during forging process is affected by viscosity, temperature and solid fraction. In this study, compression experiments of aluminum alloy were performed under each other tool shape which is rectangle shape(square array), rectangle shape(hexagonal array), and free shape tool. In addition, the dynamics behavior compare with Okano equation to power law model which is viscosity equation.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.150-157
• /
• 1996

In this paper, to develop a smart CAD/CAM system for systematically performing from the 3-D solid shape design of products to the CNC cutting operation of products by a machining center, a B-Rep solid modeler is realized based on the half edge data structure. Because the B-Rep solid modeler has the various capabilities related to the solid definition functions such as the creation operation of primitives and the translational and rotational sweep operation, the solid manipulation functions such as the split operation and the Boolean set operation, and the solid inversion function for effectively using the data structure, the 3-D solid shape of products can be easily designed and constructed. Also, besides the automatic generation of CNC code, the B-Rep solid modeler can be used as a powerful tool for realizing the automatic generation of finite elements, the interfer- ence check between solids, the structural design of machine tools and robots and so on.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.48-54
• /
• 2004

This paper describes the development of automatic shape design program for spur gear. It produces automatically third-dimensional surface and solid model used in CAD/CAM system with inputting simple measurements. This program can maximize user's convenience and get surface and solid model quickly as accepting GUI(graphic user interface). Automatic shape design program for spur gear was developed by Visual LISP, a developer program. Besides, a geometrical method and a mathematical algerian are used in this program. Use frequency of a fine spur gear is on the increase recently and manufacture process of this gear is heat treatment after press processing with molding. In this press processing, the upper punch portion of a fine spur gear shape is drafted by CAM. Therefore, estimated that surface and solid model of spur gear used to CAM are needed in this research. In this research, after 2 ㎜ gear was modeled by auto shape design program, the upper punch portion of a fine spur gear was manufactured as giving third-dimensional model to CAM software and then, displayed the result as applying to press process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1958-1967
• /
• 2004

This paper describes the method to rapidly fabricate the large-sized physical model with the envelope model size of more than 600 mm${\times}$ 600 mm${\times}$ 600 mm using two type semi-automatic VLM-ST processes in connection with the reverse engineering technology. The fabrication procedure of the large-sized solid shape is as follows: (1) Generation of STL data from 3D scan data using 3D scanner, (2) generation of shell-type STL data by Boolean operation, (3) division of shell-type STL data into several pieces by solid splitting, (4) generation of USL data for each piece with VLM-Slicer, (5) fabrication of each piece by cutting and stacking according to USL data using VLM-ST apparatus, (6) completion of a shell-type prototype by zigzag stacking and assembly for each piece, (7) completion of a 3D solid shape by foam backing, (8) surface finish of a completed 3D solid shape by coating and sanding. In order to examine the applicability of the proposed method, the miniature of the Mount Rushmore Memorial has been fabricated. The envelope model size of the miniature of the Mount Rushmore Memorial is 1,453 mm${\times}$ 760 mm${\times}$ 853 mm in size. From the result of the fabricated miniature of the Mount Rushmore Memorial, it has been shown that the method to fabricate the large object using two type semi-automatic VLM-ST processes in connection with the reverse engineering technology are very fast and efficient.