• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.196-203
• /
• 2011

Experiments to determine heat transfer coefficients and friction factors are conducted on a stationary transverse parallel wire-screen rib roughened rectangular channel. The test section consists of 198 mm (W) x 40 mm (H) x 712 mm (L). The channel has the aspect ratio of 4.95 and hydraulic diameter of $D_h$=6.66 cm. Four wire screen ribs and a solid rib are used. 0.1 mm-thick-stainless steel foil heaters and thermocouples (T type) are used to measure the heat transfer coefficients. Reynolds numbers studied range from 20,000 to 60,000. The wire-screen rib height (e) to hydraulic diameter ($D_h$) ratio ($e/D_h$) is 0.075; spacing (p) to height ratio (p/e) is 10. Results indicate that the solid rib produces the greatest Nusselt number and friction factor.

• Journal of Welding and Joining
• /
• v.34 no.2
• /
• pp.46-53
• /
• 2016

Effect of heating rate on microstructure of brazed joints with STS 304 Printed Circuit Heat Exchanger (PCHE),which was manufactured as large-scale($1170(L){\times}520(W)){\times}100(T)$, mm), have been studied to compare bonding phenomenon. The specimens using MBF 20 was bonded at $1080^{\circ}C$ for 1hr with $0.38^{\circ}C/min$ and $20^{\circ}C/min$ heating rate, respectively. In case of a heating rate of $20^{\circ}C/min$, overflow of filler metal was observed at the edge of a brazed joints showing the height of filler metal was decreased from $100{\mu}m$ to $68{\mu}m$. At the center of the joints, CrB and high Ni contents of ${\gamma}$-Ni was existed. For the joints brazed at a heating rate of $0.38^{\circ}C/min$, the height of filler was decreased from $100{\mu}m$ to $86{\mu}m$ showing the overflow of filler was not appeared. At the center of the joints, only ${\gamma}$-Ni was detected gradating the Ni contents from center. This phenomenon was driven from a diffusion amount of Boron in filler metal. With a fast heating rate $20^{\circ}C/min$, diffusion amount of B was so small that liquid state of filler metal and base metal were reacted. But, for a slow heating rate $0.38^{\circ}C/min$, solid state of filler metal due to low diffusion amount of B reacted with base metal as a solid diffusion bonding.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.77-87
• /
• 1994

This paper deals with an automated forming sequence design system by which designers can determine desirable operation sequences even if they have little experience in the design of cold forging process. The forming sequence design in the cold forging is very important and requires many kinds of technical and empirical knowledge. They system isproposed, which generates forming sequence plans for the multistage cold forging of axisymmtrical solid products. Since the process of metal forming can be considered as a transformation of geometry, treatment of the geometry of the product is a key in planning process. To recognize the geometry of the product section, section entity representation and primitive geometries were used. Section entity representation can be used for the calculation of maximum diameter, maximum height, and volume. Forming sequence for the part can be determined by means of primitive geometries such as cylinder, cone, convex, and concave. By utilizing this geometrical characteristics (diameter, height, and radius), the product geometry is expressed by a list of the priitive geometries. Accordingly the forming sequence design is formulated as the search problem which starts with a billet geometry and finishes with a given product one. Using the developed system, the sequence drawing with all dimensions, which includes the proper sequence of operations for the part, is generated under the environment of AutoCAD. Based on the results of forming sequence, process variables(strain, punch pressure, die inner pressure, and forming load) are determined.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.1
• /
• pp.146-154
• /
• 2009

In recent tissue engineering field, it is being reported that the fabrication of 3D scaffolds having high porous and controlled internal/external architectures can give potential contributions in cell adhesion, proliferation and differentiation. To fabricate these scaffolds, various solid free-form fabrication technologies are being applied. The solid free-form fabrication technology has made it possible to fabricate solid free-form 3D microstructures in layer-by-layer manner. In this research, we developed a multi-head deposition system (MHDS) and used design of experiment (DOE) to fabricate 3D scaffold having an optimized internal/external shape, Through the organization of experimental approach using DOE, the fabrication process of scaffold, which is composed of blended poly-caprolactone (PCL), poly-lactic-co-glycolic acid (PLGA) and tricalcium phosphate (TCP), is established to get uniform line width, line height and porosity efficiently Moreover, the feasibility of application to the tissue engineering of MHDS is demonstrated by human bone marrow stromal cells (hBMSCs) proliferation test.

• FLOWER RESEARCH JOURNAL
• /
• v.16 no.4
• /
• pp.255-259
• /
• 2008

This study was conducted to investigate the effect of ridge height (10 cm, 20 cm, 30 cm, and 40 cm) on the soil physical property, the growth and flowering characteristics of Gypsophila paniculata (cv 'Bristol Fairy') in the subalpine area. As ridge height got higher, the daily soil temperature, the soil moisture content, soil hardness, bulk density, and solid phase ratio were decreased, but porosity ratio was a little increased. In summer and autumn cultivation the blooming of ridge height 30 cm and 40 cm was slightly delayed, but their root activity, cut flower width, and yield were better than those of 10 to 20 cm ridges. And the mortality ratio of plants, rosette formation rate, and nonpaniculata inflorescence rate became lower.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.303-303
• /
• 2022

The purpose of this study was to evaluate agronomic characteristics and identify the useful traits to utilize the wheat genetic resources for breeding programs by understanding the phenotypic variation among germplasm through multivariate analysis. In this study, a total of 394 wheat accessions were characterized for 15 agronomic traits using the National Agrobiodiversity Center (NAC) descriptor list, of which 31 accessions from 6 species and 363 unidentified accession (Triticum spp.) available at the NAC, Rural Development Administration (RDA), Korea. Growth characteristics such as leaf width, culm length, spike length, spikelet length, solid stemmed, days to heading, days to maturity, grain-filing period, and also seed characteristics such as width, height, area, perimeter, circle, solidity, and germination percent were studied. Among the 15 agronomic characteristics, the germination percent showed the smallest variation between resources (CV = 0.4%), and the spikelet length (CV = 66.5%) showed the highest variation. A strong positive correlation was found between seed traits such as seed height and seed area (r = 0.90), seed height and seed perimeter (r = 0.87) and seed length and width (r = 0.80). Principal component analysis (PCA) was conducted and the first five principal components comprised 76.7% of the total variance. Among the first five PCs, PCI accounted for 28.5% and PC2 for 20.0%. Wheat resources (394) were classified into four clusters based on cluster analysis, consisting of 215 resources(I), 117 resources(II), 48 resources(III), and 14 resources(IV). Among the clusters, the resources belonging to Cluster III showed the lowest seed width, height, area, and perimeter characteristics compared to other clusters. The wheat resources belonging to cluster IV had small seed width and low germination percent, but took longer to form heads and mature than resources in other clusters. These results will serve as the basis for further genetic diversity studies, and important agronomic characteristics will be used for improving wheat, including developing high-yielding and resistant varieties to biotic and abiotic stresses via breeding programs.

• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.454-462
• /
• 2014

This study was carried out to determine the effect of tree height on light transmission, spray penetration, tree growth performance, fruit quality attributes, and labor productivity in the slender-spindle system of 'Hongro'/M.9 apple trees. With increasing tree height, the light penetration into the internal parts of the canopy decreased, especially in the lower canopy. Leaf area index (LAI) increased with increasing tree height, thereby leading to a reduction in the extent of spray penetration into the interior of the canopy. With increasing tree height, shoot growth was more vigorous but produced slender shoots in the upper canopy compared to the lower canopy. Although the soluble solid content and coloration of fruit decreased, there was no difference in fruit firmness and acidity. In addition, the number of final fruit set increased, although the production of large fruit (> 305 g) decreased. The increase in tree height also significantly increased the labor required for practices such as thinning of flowers and fruits, pruning, and harvesting. Nevertheless, this problem of increased in labor input in taller trees would was eased by use of a mechanical lift. Utilizing a lift for thinning the flowers of trees 4.5 m in height saved 14.6 min per tree, compared to the use of ladder. Therefore, it is highly considerable that in order to enhance light transmission and fruit coloration, light conditions should be improved in the internal tree canopy of slender-spindle systems.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.4
• /
• pp.55-64
• /
• 2014

In this study, Intersecting Tensegrity System that is integrated solid compression members with tension members was presented. This system is set up by connecting upper and lower compression members of pyramid shape with exterior tension members. In this system, the solid compression members are intersected each other and connected by a tension member in the center. This system is a variation of Tensegrity system, has a improved feature that the system is able to induce prestresses in all of tension members easily by adjusting the distance of a tension member in the center. The proposed system was studied by modeling, and the structural behavior of the system was investigated by mechanical analysis of the model. Furthermore, the features of the structural behavior variations was investigated when the composition elements(total height, size of surface, intersection length, etc.) are changed variously. It was also showed that the system is able to be used as a temporary space structure system with a membrane roof of inverse conical shape.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.136-142
• /
• 2008

Recently, cabled-suspension bridges and suspension bridge have been increasingly built in korea. But such structures were often damaged by fire due to car collison. In this study, the cabled-suspension bridges constructed under the kind of the project of national road aggrandizement are modeled using Solid Works 2007. The COSMOS FloWorks 2007 software are used for Heat Transfer Analysis and Thermal Stress Analysis. The safety of wire, HDPE pipe and stainless steel pipe are investigated. The major variables for the analysis are the temperature of the heat source, the distance between the fire-proof bulk head and the heat source, wind velocity, and the height of the end of Stainless steel pipe.

• Electrical & Electronic Materials
• /
• v.11 no.10
• /
• pp.60-65
• /
• 1998

Deposition conditions, surface morphology, and electrical properties of polyamic acid alkylamine salts (PAAS) Langmuir-Blodgett(LB) films have been investigated through a study of surface pressure-area $\pi$-A isotherms, AFM (atomic force microscopy), and current-voltage characteristics. To obtain the optimum conditions of film deposition, the $\pi$-A isotherms were examined by varying temperature, barrier moving speed, dipping speed, spreading amount of solution etc. The Z-type LB films were made at the surface pressure of 5 mN m-1 and 25 mN m-1 for the AFM study; the former surface pressure forms the gas phase and the latter one forms the solid phase. The LB film made in the gas phase show domains with a size of about 200 A diameter and 70 A height. However, the LB films made in the solid phase show a very smooth surface with 2 A surface roughness. In the current-voltage characteristics measured along the perpendicular direction of the films, ohmic conduction has been observed below 105 V cm-1 and the calculated electrical conductivity is about 10-13 S cm-1. Nonohmic conduction has been observed above = 10-11 V cm and the conduction mechanism can be explained by the Schottky effect.