• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.258-263
• /
• 2013

We examined various ball-milling parameters which affect the structural and morphological modification of multi-wall carbon nanotubes. In particular, the effect of milling mode and the use of different milling agents were examined. Friction milling mode induced more structural changes than impact milling mode except the use of dry ice as a milling agent. Wet milling was helpful for reducing more effectively the agglomeration of nanotubes than dry milling. The use of hard solid particles such as silica and alumina as milling agents resulted in an effective shortening of nanotubes, but often susceptible to the amorphization and the destruction of crystallinity.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.279-279
• /
• 2006

We report a fabrication of carbon nanotube (CNT) monolayer thin film using liquid-liquid interface. The multiwalled carbon nanotube (MWCNT), which were synthesized by the alumina template method formed a monolayer at the liquid-liquid interface after sonicating the MWCNT water-oil dispersion. Moreover, with the addition of ethanol, the MWCNT monlayer was also formed at the liquid-liquid interface. The monolayer is transferable onto solid substrates and the transferred film was observed using atomic force microscopy (AFM)

• Corrosion Science and Technology
• /
• v.6 no.3
• /
• pp.140-146
• /
• 2007

In the paper, with corrosion velocity measurement and metallographic observation on specimens after sulfuric acid/ferric sulfate boiling experiment, intergranular corrosion tendency of the new type ultra low carbon stainless steel developed by ourselves which experienced solution treatment at different temperatures was evaluated. A VHX 500 super depth field tridimensional microscope was used to observe corrosion patterns on the sample surfaces. The depth and width of grain boundary corrosion groove were measured by the tridimensional microscope, which indicated that the corrosion degrees of the samples which received solution treatment at different temperatures are quite different. Transgranular corrosion at different degree occurred along with forged glide lines. After comparison it was proved that the stainless steel treated at $1100^{\circ}C$ performs very well against intergranular corrosion.

• Journal of the Korean Chemical Society
• /
• v.15 no.6
• /
• pp.330-347
• /
• 1971

Catalytic effects of metallic salts on the combustion of diesel fuel oil have been studied. In the case of organometallic salt, the active species are the metallic oxides resulted from combustion of the salts. The oxides act only on the residual solid carbon produced from the fuel oil combustion. The catalytic activity can be explained with the semiconductor theory just as in the case of the gas phase reaction. The chemical rate constant of the combustion of carbon, the soot from diesel fuel oil, is found to be $k_c=1.1{\times}10^4\;exp$ (-16,600/T) below $800^{\circ}K$. By addition of metallic oxides, the rate constant increases remarkably. This work has substantiated the belief that the effect of the metallic salts on the fuel oil combustion can conveniently be studied by checking directly the effect of the corresponding metallic oxide on the soot carbon.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.254-259
• /
• 1998

A kinetic model predicting the oxidation of carbon fiber reinforced glass matrix composites has been described. The weight loss of composites during oxidation implied that a gasification of carbon fiber takes place and the transport of reactants $(O_2)$ or product (CO or $CO_3$) in the glass matrix was partially the rate controlling step. The kinetic model in this study was based on the work of Sohn and Szekely which may be regarded as a generalization of numerous models in the gas-solid reaction system. A comparison of this model with experimental data is also presented.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.83.2-83.2
• /
• 2011

In this study, we fabricated tubular ceramic support for segmented-in-series solid oxide fuel cell (SOFC) by using MAO(MgAl-stabilized ) as main material and activated carbon as pore former. Thermal expansion properties of ceramic support with different amounts of activated carbon were analyzed by using dilatometer to decide a suitable sintering temperature. The tubular ceramic supports with different amounts of activated carbon (15, 20, 30wt.%) were fabricated by the extrusion technique. After sintering at $1400^{\circ}C$ for 2h, cross section and surface morphology of tubular ceramic support were analyzed by using SEM image. Also, the porosity, mechanical property, gas permeability of tubular ceramic supports was measured. Based on these results, we established the suitable fabrication technique of tubular ceramic support for segmented-in-series SOFC.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.47-50
• /
• 2003

Carbon-silica membranes were Prepared by Pyrolyzing polyimide/silica composite obtained from ill-situ polymerization of alkoxy silanes via sol-gel reaction. In this study, effects of silica content and silica network in polyimide matrix were focused on the gas permeation and separation properties of the final carbon-silica membrane. The membranes prepared were characterized with a field emission scanning electron microscopy (FE-SEM), a solid state $^{29}$ Si nuclear magnetic resonance spectroscopy ($^{29}$ Si-NMR), an electron spectroscopy for chemical analysis (ESCA), a thermogravimetric analysis (TGA) and gas permeation tests.

• Korean Journal of Metals and Materials
• /
• v.50 no.9
• /
• pp.637-643
• /
• 2012

Recently, because of safety and environmental concerns, there has been a tendency to introduce solid self-lubricating composites for bearing materials. In this paper, we developed Fe-Cr-C-Mn-Cu cast composite alloys as a self-lubricating composite and investigated the effect of carbon on the formation of protective tribofilms during sliding. The wear resistance of these materials was mainly affected by carbon concentrations due to the fact that in particular wear passed from delamination to tribo-oxidation, reducing the wear rate. The improved wear resistance likely resulted from protective tribofilms that formed on the surface during sliding.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.529-532
• /
• 2001

Korean food waste, one of the abundantly available but environmentally problematic organic wastes in Korea, was utilized as solid-substrate by fungal strain Aspergillus niger ATcC 6275 for the production of enzymemixture containing amylase, cellulase and xylanase. The enzyme mixture can be used as high value-added animal feed. Solid-state fermentation method yielded a 84-fold enhancement in xylanase activity compared with submerged fermentation method. The effect of incubation period, incubation temperature, pH of medium, moisture content, inoculum size and enrichment of the medium with nitrogen and carbon sources were observed for optimal production of these enzymes The optimal amylase activity of 33.10 U/g, cellulase activity of 24.41 U/g, xylanase activity of 328.84 U/g were obtained at 8 days incubation with 50%(w/w) soy bean flake, with incubation temperature of $25^{\circ}C$, pH of 6.38, optimal moisture content of 55% and with inoculum size of $3.8{\times}10^6$spore/g. Enzyme activities were enhanced when ImM $CaSO_4$, 2% Malt extract and 2% galactose were added as mineral, nitrogen and carbon enrichment respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.5
• /
• pp.473-481
• /
• 2007

Compared to other types of fuel cells, SOFC has advantages like a wide output range and the direct use of hydrocarbon fuel without the process of external reforming. Particularly because the direct use of fuel without reforming reaction is closely linked to overall system efficiency, it is a very attractive advantage. We tried the operation with methane. However, although methane has a small number of carbons compared to other hydrocarbon fuels, our experiment found the deposition of carbon on the surface of the SOFC electrode. To overcome the problem, we tried the operation through activating internal reforming. The reason that internal reforming was possible was that SOFC runs at high temperature compared to other fuel cells and its electrode is made of Ni, which functions as a catalyst favorable for steam reforming.