위성은 임무수행을 위하여 발사체에 탑재되어 목표하는 궤도상에 도달하게 된다. 발사체의 비행동안 위성은 사인, 랜덤, 충격과 같은 극심한 발사 진동환경에 노출되게 되며, 이에 따라 위성체 내부에 위치한 전장품 및 전장품 기판에는 각 진동요소에 의한 발사 하중이 작용하게 된다. 발사하중 작용시, 전장품 내부에 장착된 기판은 체결부를 경계로 수직방향의 굽힘 거동을 주로 일으키게 되며, 이로 인한 상대변위로 기판 위 소자의 납땜부 파괴와 도선의 단선, 기판 자체의 균열을 초래한다. 성공적인 임무 수행을 위해서, 위성의 전장품 설계는 상기 현상들에 대해 기판의 구조 건전성 및 피뢰파괴 신뢰도가 확보되어야한다. 본 논문에서는 기존에 구조해석이 기 수행되었던 다목적실용위성 3호에 탑재되는 고해상도 위성카메라용 X-band 안테나 구동장치인 APD(Antenna Pointing Driver) 전장품의 제어 보드를 대상으로 하여, 스테인버그의 식을 통해 진동 하중에 의한 허용 처짐과 최대 처짐을 도출해내고, 팔머그렌 마이너 방정식을 이용하여 수명관점에서 피로파괴 예측의 유효성을 입증하였다.
다양한 산업분야에서 전자기판과 전장품의 기계적 체결을 위해 적용되는 웨지락(Wedge Lock)은 우주용 전장품에서도 장·탈착 용이성, 발사진동저감 효과 때문에 폭넓게 적용되고 있다. 그러나 기판의 가장자리에만 제한적으로 구속 가능한 장착 조건 때문에 기판의 크기가 증가할수록 극심한 발사환경에서의 굽힘거동에 의한 전자소자 솔더부의 피로수명 보장에 한계가 존재한다. 종래에는 상기 굽힘거동 최소화를 위해 기판에 별도의 보강재를 적용하였으나, 이는 전장품의 무게 및 부피증가가 불가피하다. 본 연구에서는 상기 한계점을 극복하고자, FR-4 재질의 박판을 기판의 배면부에 다층으로 적층하고, 각 층간에 점탄성 테이프를 적용하여 발사환경에서 소자의 피로수명 확보에 유리한 고댐핑 적층형 전자기판을 제안하였다. 본 적층형 기판의 설계 유효성 검증을 위해 상이한 온도조건에 따른 자유감쇠시험 및 인증 수준의 발사진동시험을 수행하였으며, 시험 결과에 기반한 고집적화 소자의 피로수명을 예측하였다.
The impulse between launch vehicle and atmosphere can generate a lot of noise and vibration during the process of launching a satellite. Structurally, the electronic equipment of a satellite consists of an aluminum case containing PCB. Each PCB has resistors and IC. Noise and vibration of the wide frequency band are transferred to the inside of fairing, subsequently creating vibration of the electronic equipment of the satellite. In this situation, random vibration can cause malfunctioning of the electronic equipment of the device. Furthermore, when the frequency of random vibration meets with natural frequency of PCB, fatigue fracture may occur in the part of solder joint. The launching environment, thus, needs to be carefully considered when designing the electronic equipment of a satellite. In general, the safety of the electronic equipment is supposed to be related to the natural frequency, shapes of mode and dynamic deflection of PCB in the electronic equipment. Structural vibration analysis of PCB and its electronic components can be performed using either FEM or vibration test. In this study, the natural frequency and dynamic deflection of PCB are measured by FEM, and the safety of the electronic components of PCB is evaluated according to the results. This study presents a unique method for finite element modeling and analysis of PCB and its electronic components. The results of FEA are verified by vibration test. The method proposed herein may be applicable to various designs ranging from the electronic equipments of a satellite to home electronics.
In this study, active metal brazing methods for $ZrO_2$ and Ti alloy were discussed. To get a successful metal-ceramic bonding, various factors (melting temperature, corrosion, sag resistance, thermal expansion coefficient etc. of base materilas and filler metal) should be considered. Moreover, in order to clarify bonding between the metal and ceramic, the mechanism of the interfacial structure of the joints should be identified. The driving force for the formation of metal and ceramic interfaces is the reduction of the free energy which occurs when their contact becomes complete. Interfacial bonding depends on the material combinations and the bonding processes. This study describes the bonding between ceramic and metal in an active metal brazing.
마이크로솔더링에 의한 전자기기는, 사회기능의 중추가 되는 컴퓨터, 통신 기기, 항공기 인공위성 등의 제어계를 구성하므로, 그 접속부에 대한 높은 신뢰성의 요구는 그 무엇보다 중요하다. 전자기기에 있어서의 솔더 접속부는 집과 기판의 전기 적.기계적 접속의 역할을 하고 있으며, 따라서 개개의 접속부의 파단은 전체의 불량 으로 연결된다. 실제 전자콤포넌트와 그 시스템의 단선 등의 사고에 있어서 자주 발생 하는 사고중의 하나가 솔더접속부의 단선에 의한 것이며, 그 단선중에서도 가장 보편 적이며 또한 대단히 심각한 문제로서 주목을 받고 있는 것이 솔더접속부의 열피로파단 이다. 전자기기를 사용할 때, 스위치의 on-off에 의한 power cycle과 환경의 온도변화 에 기인하는 반복열 사이클은 솔더접속부의 피로를 일으키게 되고, 결국에는 사용중에 파단을 초래하게 된다. 이러한 온도변화의 범위는 약 -55.deg. - 150.deg.C로 예상할 수 있으며, 여기서 최고온도인 150.deg.C는 Pb-Sn 공정합금의 경우 0.9Tm.p.이상의 고온에 해당한다. 이 피로는 등온적으로 또는 열사이클중에 발생하기도 한다. 솔더접 속부의 열피로수명은 대부분의 공업재료에서 나타나는 저사이클피로거동과 유사하게 발생하며, 솔더 접속부에 인가되는 열변형/응력(thermal strain/stress)의 크기에 크게 의존하는 것으로 알려져 있다. 솔더는 서로 다른 열팽창계수를 갖는 칩과 회로 기관의 두종류의 재료를 접속하기 때문에, 상기한 바와 같은 반복열사이클에 의하여 발생하는 열변형/응력이 접속부의 피로.파단을 야기시킨다. 이러한 솔더접속부에 대한 주기적인 응력/변형의 인가는 접속부에 내.외적으로 현저한 변화를 야기시키게 되고, 열피로로 연결되며 결국에는 시스템의 전기적 단선을 초래하게 된다. 또한 열피로파단 현상는 변형/응력의 크기 뿐 만아니라 솔더합금자체의 야금학적인 물성에도 크게 의존 하며, 내적.외적인 열변화에 의한 야금학적인 특성변화도 크게 영향을 미친다. 솔더 접속부의 신뢰성에 대한 연구는, 그 중요성에 비추어 볼 때, 지금까지 수많은 연구가 행하여져 왔다. 그러나 신뢰성과 관련된 열피로파단현상에 대한 야금학적인 면에서의 연구는 비교적 적은 편이다. 따라서 본 해설에서는 전자기기의 마이크로 솔더접속부 에서 발생하는 열피로파단현상에 대한 야금학적인 면에 중점을 두어 서술하고자 한다.
The impulse between launch vehicle and atmosphere can generate a lot of noise and vibration during the process of launching a satellite. Structurally, electronic equipment (KOMPSAT 2, RDU : Remote Drive Unit) of a satellite consists of aluminum case containing PCB (Printed circuit boards). Each PCB has resistors and IC (Integrated circuits). Noise and vibration of wide frequency band are transferred to the inside of fairing, subsequently creating vibration of the electronic equipment of the satellite. In this situation. random vibration can cause malfunctioning of the electronic equipment of the device. Furthermore, when tile frequency of random vibration meets with natural frequency of PCB. fatigue fracture nay occur in the part of solder joint. The launching environment, thus. needs to be carefully considered when designing the electronic equipment of a satellite. In general. the safety of the electronic equipment is supposed to be related to the natural frequency, shapes of mode and dynamic deflection of PCB in the electronic equipment. Structural vibration analysis of PCB and its electronic components can be performed using either FEM(Finite Element Method) or vibration test. In this study. the natural frequency and dynamic deflection of PCB are measured by FEM, aud the safety of the electronic components of PCB is being evaluated according to the results. This study presents a unique method for finite element modeling and analysis of PCB and its electronic components. The results of FEA are verified by vibration test. The method proposed herein may be applicable to various designs from the electronic equipments of a satellite to home electronics.
전자부품에 대한 보드실장은 아직까지 솔더를 이용한 접합기술을 주로 이용하고 있다. 그러나, 솔더의 크? 및 피로특성으로 인한 접합부 내구한계로, 자동차 전장모듈에서는 반영구적인 접합기술인 프레스 핏(Press-fit) 접합기술 적용을 확대하고 있다. 프레스 핏 접합은 프레스 핏 금속단자를 보드내 쓰루 홀(Through hole)에 기계적으로 삽입하여 체결하는 접합기술로써, 적절한 금속단자의 소성변형으로 쓰루 홀 내부 표면접합을 밀착시킴으로써 강건한 접합을 유도한다. 본 논문에서는 보드내 쓰루 홀 크기 및 표면처리에 따른 프레스 핏 접합 특성 및 신뢰성을 솔더링과 함께 비교하기 위해, 보드 쓰루 홀 크기에 따른 삽입강도 및 삽발강도를 평가하였으며, 열충격 시험을 통한 실시간 저항변화를 통해 프레스 핏 및 솔더링 접합부의 저항변화를 관찰하였다. 또한, 각 접합부위 분석을 통한 프레스 핏 및 솔더링 접합열화를 분석하여 주요 파손모드를 고찰하고자 하였다.
Purpose : To understand the impact on the strength or restoration force by the change of heating temperature when soldering 18-8 stainless steel round wire which is the chrome-nickel class for dental orthodontic device production. Methods : The following conclusions were made upon the results from tensile strength test, 3 point bending test, and $90^{\circ}$ bending fatigue test with 24 samples that had been applied with condition 1 (before heat treatment - natural) and condition 2 (after heat treatment - mooring 30 seconds after heating up to $500^{\circ}C$, $700^{\circ}C$, and $900^{\circ}C$) to ${\phi}0.4mm$, ${\phi}0.7{\beta}mm$, 18-8 stainless steel round wire (spring hard) by Jinsung Company. Results : When it was heat-treated at $900^{\circ}C$, both ${\phi}0.4mm$ and ${\phi}0.7mm$ showed very low tensile strengths compared to the heat treated cases at $500^{\circ}C$ and $700^{\circ}C$ Yield strengths of both ${\phi}0.4mm$ and ${\phi}0.7mm$ showed very low compared to the heat treated cases at natural, $500^{\circ}C$, and $700^{\circ}C$, as well. Upon the results of 3 point bending test, the heat treated case at $900^{\circ}C$ showed very low in both ${\phi}0.4mm$ and ${\phi}0.7mm$, compared to the heat treated cases at natural, $500^{\circ}C$, and $700^{\circ}C$. Tensile strength of both ${\phi}0.4mm$ and ${\phi}0.7mm$ as well, showed very low compared to the heat treated cases at natural, $500^{\circ}C$, and $700^{\circ}C$. Upon the results of $90^{\circ}$ bending fatigue test, the heat treated case at $900^{\circ}C$ showed the highest wave node resistance in both ${\phi}0.4mm$ and ${\phi}0.7mm$. Conclusion : This study concluded that heating temperature change during wire soldering impacts on the characteristics of orthodntic wire.
최근 우주용 전장품에 다양한 실장형태의 고집적 소자가 적용됨에 따라, 기계적 환경에서의 고신뢰성 확보를 위해 인증모델 제작 전 잠재적 위험요소에 대한 조기진단으로 개발기간 및 비용 절감이 가능한 설계절차 구축이 요구된다. 고신뢰도 전장품 설계를 위해 기존에 적용되어온 Steinberg의 피로파괴이론은 최근 다양한 크기와 실장기법의 소자를 갖는 우주용 전장품에 적용하기에는 이론적 한계와 이들 각각에 대한 모델링 기법에 따라 상이한 결과가 도출되는 등의 한계가 존재한다. 이를 해결하기 위해 소자의 상세 유한요소모델을 구축할 시, 다수의 실장구조를 갖는 고집적화 기판을 모델링하기에는 많은 시간이 소요되는 단점이 존재한다. 본 논문에서는 고신뢰도 전장품 설계기법 구축을 위해 기존 사업에서 적용된 설계와 다른 접근방법의 일환으로 상용 신뢰성 수명예측 도구인 Sherlock을 이용하여 차세대중형위성용 탑재 전장품인 CCB(Camera Controller Box)에 대한 인증시험수준에서의 고장 메커니즘 별 신뢰성 평가를 수행하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.