• 설비공학논문집
• /
• 제20권4호
• /
• pp.260-265
• /
• 2008

The excess heat that is generated from PV modules can be removed and converted into useful thermal energy. A photovoltaic/thermal (PVT) module is a combination of photovoltaic module with a solar thermal collector, forming one device that converts solar radiation into electricity and heat simultaneously. In general, two types of PVT can be distinguished : glass-covered PVT module, which produces high-temperature heat but has a slightly lower electrical yield, and uncovered PVT module, which produces relatively low-temperature heat but has a somewhat higher electrical performance. In this paper, the experimental performance of water type PVT combined module, glass-covered, analyzed. The electrical and thermal performance of the module were measured in outdoor conditions, and the results are analyzed. The results showed that the thermal efficiency of the PVT module was 27.6% average and its PV efficiency was about 10.0% average, both depending on solar radiation, inlet water temperature and ambient temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.3-4
• /
• 2008

Photovoltaic module consists of serially connected solar cell which has low voltage characteristics. But, the other way, the whole current flow of PV module is restricted by lowest current of one solar cell. For the experiment, we make PV module composing the solar cells that have short circuit current difference of 0%, 1%, 3% and 5%. Using Light I-V and Dark I-V measurements, electrical characteristic parameters like Isc(short-circuit current), Voc(open-circuit voltage), Rs(series resistance), Rsh(shunt resistance) are analyzed. PV module of low current characteristics has electrical stress from other modules. And, such a module has a tendency of hot-spot suffering which leads degradation.

• 전기학회논문지P
• /
• 제59권3호
• /
• pp.293-297
• /
• 2010

Next generation concentrating photovoltaic technologies could have a large-scale impact on world electricity production once they will become economically attractive and grid parity will be reached. Multi-junction solar cells will be characterised by a high value of the cell economical performance index if the cells were able to operate at high concentration level. Concentrating the sunlight by optical devices like lenses or mirrors reduces the area of expensive solar cells or modules, and, moreover, increases their efficiency. Accurate and reliable tracking is an important issue to maintain high the CPV system output power. Further, for high concentration CPV systems, the actual tracker cost is about 20% of the total CPV system cost. In this paper high-concentration is defined as systems using concentration ratios well above 100 times the one sun intensity and trackerlss CPV system studied. Using sphericalness lens and parallel MJ cell connection method were suggested and achieved experiment on a clear day in summer. Development of these high performance multi-junction CPV module promises to accelerate growth in photovoltaic power generation.

• 한국결정성장학회지
• /
• 제5권1호
• /
• pp.67-77
• /
• 1995

태양전지가 시장성을 확보하는데 가장 중요한 요소는 전지의 가격이다. 기존의 결정질 실리콘 태양전지에서는 가격의 절반 정도가 웨이퍼가격이다. 결과적으로 이러한 가격을 줄이기 위해서 박막 제조 기술에 많은 노력이 집중되고 있으며 박막형 태양전지의 효율을 증가시키기 위한 많은 기술적인 발전이 되고 있다. 박막형 태양전지의 기술에 관한 기술 발전은 다결정 실리콘(p-Si), 비정질 실리콘(a-Si), $SuInSe_2$(CIS), CdTe 등에서 주로 이루어지고 있다. 본 논문은 박막형 태양전지 분야에 있어서의 최근 연구성과에 대해서 알아보았다.

• 한국태양에너지학회 논문집
• /
• 제23권2호
• /
• pp.81-90
• /
• 2003

UTAC(unglazed transpired air collector) system has unique advantage for space heating and tempering ventilation air over the conventional collector system such as flat plate and vacuum collector. UTAC can improve radiative and convective loss due to nonglazed component and enhanced plate surface configuration. and heating energy and its equivalent green house emission performance can be improved from the use of this like collector in building application. The Option D Calibration simulation approach of IPMVP(International Performance Measurement and Verification Protocol) in ESCO businesses has been recommended to use of the calibrated computer modules like these Energy-10. DOE2.1E and TRNSYS(transient system simulation). This study is to develop subroutine type-203 of TRNSYS15.2 program and appraise thermal performance of UTAC. With newely addeded subroutine type-203. 1) Thermal performance of unglazed transpired collector could be possible based on dimensionless variables such as efficiency and heat exchanger effectiveness. and 2) Assessement of energy consists of solar useful and insulation saving for UTAC could be possible.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.25-26
• /
• 2007

In this paper, we studied the shadow effect which is one of environmental cause for hot-spot phenomenon on PV by considering electrical effects. We fabricated PV module in case of existence and nonexistence of bypass diode. And maximum output power and thermal distribution was analyzed by shadowing solar cell by increase of 5%. From the results, the PV module's(without bypass diode) maximum output power was reduced by hot-spot gradually. But the PV module's(with bypass diode) maximum output power had no reduction by operation of bypass diode, though solar cell is shadowed more than 60%. The solar cell temperature of PV module(without bypass diode) was $10^{\circ}C$ higher compared to module's one. This is a reason for shortening of durability of PV module.

• 한국태양에너지학회 논문집
• /
• 제39권3호
• /
• pp.29-45
• /
• 2019

As the solar energy market grows, the need to investigate the potential of photovoltaic system is being highlighted. However, due to the lack of plain field, the system on top of buildings is being exploited. This paper analyzes the potential to install PV systems on the rooftops. First of all, with the aid of a photovoltaic system simulation software, buildings were designed in a specific area based on the architectural data. And then, with the same software, the potential to install photovoltaic system was explored by placing PV modules on the buildings' rooftops. The installation potential was calculated and simulated with consideration for obstacles on the rooftops. The parameters are composed of available area for system installation, area utilization rate, PV system power capacity, operation yield hour per day and performance ratio. In the simulation, 5 sites were analyzed based on their architectural data. In the end, reliable data that can be utilized were collected for the potential to install the system with the photovoltaic system simulation software.

• Advances in nano research
• /
• 제13권5호
• /
• pp.475-485
• /
• 2022

Crystalline silicon photovoltaic cells have advantages of zero pollution, large scale and high reliability. A major challenge is that sunlight wavelength with photon energy lower than semiconductor band gap is converted into heat and increase its temperature and reduce its conversion efficiency. Traditional cooling PV method is using water flowing below the modules to cool down PV temperature. In this paper, the idea is proposed to reduce the temperature of the module and improve the energy conversion efficiency of the module through the modulation of the solar spectrum. A spectrally selective nanofilm reflector located directly on the surface of PV is designed, which can reflect sunlight wavelength with low photon energy, and even enhance absorption of sunlight wavelength with high photon energy. The results indicate that nanofilm reflector can reduce spectral reflectivity integral from 9.0% to 6.93% in 400~1100 nm wavelength range, and improve spectral reflectivity integral from 23.1% to 78.34% in long wavelength range. The nanofilm reflector can reduce temperature of PV by 4.51℃ and relatively improved energy conversion efficiency of PV by 1.25% when solar irradiance is 1000 W/m². Furthermore, the nanofilm reflector is insensitive in sunlight's angle and polarization state, and be suitable for high irradiance environment.

• 패션비즈니스
• /
• 제19권4호
• /
• pp.92-108
• /
• 2015

This study aimed at developing a down jacket prototype that utilized sunlight as an alternative energy source with no air pollution. The jacket is filled with flexible solar panels and has a heat-generating function and LED function. In this study, three smart down jacket prototypes were developed, and the jacket's capabilities were demonstrated through the thermal effect on the performance test. The typical output voltage of the flexible solar panels was 6.4V. By connecting the 2 solar cell modules in series, the final output voltage was 12.8V. A battery charge regulator module was used the KA 7809 (TO-220) of 9V. Three heating pads were to be inserted into the belly of the jacket as direct thermal heating elements, and the LED module was configured, separated by a flash and an indicator. The smart down jacket was designed to prevent damage to the down pack without the individual devices' interfering with the human body's motion. Because this study provides insulation from extreme cold with a purpose, the jacket was tested for heat insulation properties of non-heating, heating on the back, heating on the abdomen, and heating on both the back and abdomen in a sitting posture in a static state. Thermal property analysis results from examining the average skin temperature, core temperature, and the temperature and humidity within clothing showed, that placing a heating element in one place was more effective than distributing the heating elements in different locations. Heating on the back was the most effective for maintaining optimal skin temperature, core temperature, and humidity, whereas heating on the abdomen was not effective for maintaining optimal skin temperature, core temperature, or humidity within clothing because of the gap between the jacket and the body.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.17-22
• /
• 2011

There are some degradation factors for amorphous silicon solar cells. Light inducing is one of the factor that explained by Staebler-Wronski effect. Also, hotspot heating could be the reason that makes amorphous silicon solar cell degrade. Hotspot heating is occurred when a solar cell is shaded so this work is investigated into two types of shading condition and how these affect to solar cell differently. Reduced irradiance for whole cell and partially shaded as 0($W/m^2$) while the other part of cell is soaking as 1000($W/m^2$) of irradiance are two conditions that are experimented. The two types of shading show different characteristics of degradations. The result shows that partially shaded cell dropped maximum powerless and slower. Also sudden drop points have shown that should be concerned to decide the number of cells for a string. Otherwise, the current through a shaded cell might flow more than cell's capability. It makes cell and module damaged. This work would help to manufacture modules.