• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2006년도 학술발표회 논문집
• /
• pp.1964-1969
• /
• 2006

In order to solve the problem of the existing gate it developed the solar energy gate. The solar energy gate quotient a friction force from the area contact which will call improved with line contact and it diminished. Because of the result, The operation power of the gate came to be small and the small-sized of the motor was possible. From the small-sized of the motor, the solar energy system introduction was possible and the expense for the production establishment of the gate was diminished. From KRC in 2005 demonstration it establishes the solar energy gate in nationwide 50 places and characteristic the monitoring efficiently.

• 한국전산유체공학회지
• /
• 제20권2호
• /
• pp.46-51
• /
• 2015

In this paper, we have developed numerical model for particulated flow through narrow slit using Eulerian-Granular method. Commercial software (FLUENT) was utilized as simulation tool and main focus was to identify the effect from various numerical options for modeling of solid particles as continuos phase in granular flow. Gidaspow model was chosen as basic model for solid viscosity and drag model. And lun-et-al model was used as solid pressure and radial distribution model, respectively. Several other model options in FLUENT were tested considering the cross related effect. Mass flow rate of the particulate through the slit was measured to compare. Due to the high volume density of the stacked particulates above the slit, effect from various numerical options were not significant. The numerical results from basic model were also compared with experimental results and showed very good agreement. The effects from the characteristics of particles such as diameter, angle of internal friction, and collision coefficient were also analyzed for future design of velocity resistance layer in solar thermal absorber. Angle of internal friction was found to be the dominat variable for the particle mass flow rate considerably. More defined 3D model along with energy equation for complete solar thermal absorber design is currently underway.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2005년도 학술발표논문집
• /
• pp.193-198
• /
• 2005

The solar energy floodgate which discusses will minimize a quotient bringing up for discussion friction resistance and it will do to write a disturbance power, with the base which will reach it will be able to use the solar power unit in order. It is a plan which to magnification supply the practicality and will give proof will the effort with the irrigation facility of the farming village. Magnification supply of the solar energy floodgate which it sees hazard the stack supervisor and the possibility the use against the farmer and the easy frost does the monitoring against and the work which it complements is necessary.

• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• 태양에너지
• /
• 제18권4호
• /
• pp.59-66
• /
• 1998

It was compared with experimental data to verify TRNSYS Model of the thermosyphon hot water system and the various simulations were conducted to optimize the component parameters of the system. To obtain consistent simulation results the system model, which could accurately describ the thermal storage tank temperature stratification and the friction head for mass flow rate, was used. The optimization of collector parameters(collector aspect ratio, riser numbers per header unit length), thermal storage tank parameters(ratio of tank length to tank diameter, heat exchanger type), system parameters(ratio of tank volume to collector area) was simulated by TRNSYS program. The simulation results indicate that the system performance is more effected by collector aspect ratio and the ratio of tank volume to collector area than the othor parameters.

• 한국태양에너지학회 논문집
• /
• 제36권6호
• /
• pp.25-35
• /
• 2016

In this study, the evaluation of the dynamic behavior and thermal performance of the "Façade integrated Natural circulation Solar Water Heating System" installed in the residential house was carried out. Experimental tests were performed during the all year around in the rural houses of $166m^2$ in size. Facade integrated solar collector of $5m^2$ were installed on the south-facing. Electrical heater of 1 kW capacity as an auxiliary heater was installed at the upper part of the heat storage tank. The analyzing results are as follows. (1) Monthly average solar fraction was 51 to 87% and yearly average value is 64%. (2) Hot water supply temperature in December which has the lowest solar altitude is 37 to $76^{\circ}C$. The highest working fluid temperature of solar collector in this period was below $84^{\circ}C$. The temperature difference of working fluid between the collector inlet and outlet has been shown to be around 9 to $26^{\circ}C$. (3) Overheating which is one of the biggest problems during summer did not appear at all, but rather had hot water supply temperature is rather low as $30{\sim}47^{\circ}C$ in summer than winter, which is supplied by a small solar load. The solar collecting temperature has been shown to maintain below $55^{\circ}C$. (5) The thermal performance of Facade integrated solar collector can be increase due to the reduction of heat loss to the back of the collector wall integration of the collector is reduced. As a conclusion, Facade integrated natural circulation type Solar Water Heating System is a well-functioning without any pumps or controllers, and it was found that the disadvantages of conventional solar water heaters, hot water or hot water system can be greatly improved.

• 한국태양에너지학회 논문집
• /
• 제33권6호
• /
• pp.85-91
• /
• 2013

It is essential to reduce the amount of fossil fuel because facing with the natural problem such as a global warming. To achieve this goal, many of interests in the use of renewable energy is growing. Especially, as one of these renewable energy systems, a solar air heater invention has been conducted for enhancing the efficiency of solar air heater. According to this trend, scale-down sized experiment apparatus was constructed and performed for searching a proper fin and confirming the heat transfer performance by fin shape on constant heat condition to enhance efficiency of solar air heater. In this experiment, heat gain, convection heat transfer coefficient, number of transfer units, Nusselt number, Reynold's number, friction factor, performance factor were investigated in order to evaluate the thermal characteristics based on the real data obtained. By comparison with the each fin performance, a zigzag shape keeping a right angle to the plate had the highest value among them.

• 한국항공우주학회지
• /
• 제44권3호
• /
• pp.228-239
• /
• 2016

CNUSAIL-1은 $4m^2$ 크기의 태양돛을 탑재한 3U 크기의 큐브위성이며, 주 임무는 지구 저궤도에서 태양돛을 성공적으로 전개하고 태양돛을 이용해 Drag Sail을 실현하는 것이다. 또한, 이에 따른 자세와 궤도에 대한 영향을 확인하는 임무를 수행한다. 본 논문에서는 CNUSAIL-1의 태양돛에 사용되는 박막과 붐의 재질과 물성치에 관련된 실험을 수행하며, 이를 통해 태양돛 박막의 반사율/투과율 요구도를 확인하고, 박막과 붐의 인장강도를 측정함으로서 지구 저궤도 환경에서의 돛 전개 시 발생가능 응력에 대한 안전성을 확인한다. 또한, 태양돛의 전개장치를 개발 제작하여 우주환경을 모사한 지상시험을 수행함으로서 태양돛 전개의 가능성을 검증하였으며, 태양돛의 탑재와 접기 방법에 따라 비교 전개하는 실험을 통하여 접기방법을 결정하고, Spiral spring 두께에 따른 전개실험과 각속도 시험을 수행하여 실제 전개 시에 생길 수 있는 위성체에 대한 영향성 등을 살펴보았다.

• Corrosion Science and Technology
• /
• 제20권1호
• /
• pp.7-14
• /
• 2021

PosMAC^® is a brand of Zn-Mg-Al hot-dip coated steel sheet developed by POSCO. PosMAC^® can form dense surface oxides in corrosive environments, providing advanced corrosion resistance compared to traditional Zn coatings such as GI and GA. PosMAC^® 3.0 is available for construction and solar energy systems in severe outdoor environments. PosMAC^®1.5 has better surface quality. It is suitable for automotive and home appliances. Compared to GI and GA, PosMAC^® shows significantly less weight reduction due to corrosion, even with a lower coating thickness. Thin coating of PosMAC^® provides advanced quality and productivity in arc welding applications due to its less generation of Zn fume and spatters. In repeated friction tests, PosMAC^® showed lower surface friction coefficient than conventional coatings such as GA, GI, and lubricant film coated GA. Industrial demand for PosMAC^® steel is expected to increase in the near future due to benefits of anti-corrosion and robust application performance of PosMAC^® steel.

• 한국기계가공학회지
• /
• 제15권3호
• /
• pp.28-35
• /
• 2016

Forging operations are non-stationary processes occurring because of indirect pressure, generally, under conditions of three-dimensional stress and deformation. Furthermore, due to friction and the constraints of die geometry, deformation is not homogeneous. Material flow and deformation are largely determined by the shape of the tools. It is well known that net-shape forging can improve the mechanical strength of the final product as well as reduce material waste. Oxygen-free copper that is used for electrical and electronic components has excellent electrical and thermal conductivity. Oxygen-free copper parts have a low productivity in cutting process. Thus, the forging process is performed in order to improve the low productivity in cutting process. The forging of oxygen-free copper for electrode body parts was modeled using finite element simulation and forging experiments that were conducted for producing electrode body parts at room temperature. In order to reduce the cost of cutting products, the forging was performed in a closed cavity to obtain near-net or net-shape parts.