• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.202-207
• /
• 2008

Measures for coping with energy shortage are being sought all over the world. Following such a phenomenon, effort to use less energy in the design of buildings and equipment are being conducted. In particular, a program to evaluate the performance of a building comes into the spotlight. However. indispensable standard wether data to estimate the exact energy consumption of a building is currently unprepared. Thus, after appling standard weather data for four weather factors which were used in previous researches to Visual DOE 4.0, we compared it with the result of the existing data and evaluated them. For the monthly cooling and heating load of our target building, we used revised data for June, July, August, and September during which cooling load is applied. When not the existing data but the revised data was used, the research shows that an average of 14.9% increased in June, August, and September except for July. Also, in a case of heating load, the result by the revised data shows a reduction of an average of 11.9% from October to April during which heating load is applied. In particular, the heating loads of all months for which the revised data was used were more low than those of the existing data. In the maximum cooling and heating load according to load factors, the loads by residents and illumination for which the revised data was used were the same as those of the existing data, but the maximum cooling loads used by the two data have a difference in structures such as walls and roofs. Through the above results, the research cannot clearly grasp which weather data influences the cooling and heating load of a building. However, in the maximum loads by the change of weather data in four factors (dry-bulb temperature, web-bulb temperature, cloud amount, and wind speed) among 14 weather factors, the research shows that 5.95% in cooling load and 27.56% in heating load increased, and these results cannot be ignored. In order to make weather data for Performing energy performance evaluation for future buildings, the flow of weather data for the Present and past should be obviously grasped.

• Korean Journal of Soil Science and Fertilizer
• /
• v.5 no.2
• /
• pp.75-82
• /
• 1972

The proposed hypothesis that the effects of climatic factors during ripening period (from 10 days before heading to 30 days after heading) on ripened grain ratio are equal on the level of canopy and on the level of tiller in that canopy of rice plant appeared to be agreeable. The followings were found according to the analysis of ripening structure at tiller level. 1. The optimum ripening temperature (mean air temperature during ripening period) was $21^{\circ}C$ for Jinheung and $22^{\circ}C$ for IR667-Suwon 214. 2. The minimum mean solar radiation ($cal\;cm^{-2}\;day^{-1}$) of ripening period was not greater than 240 for Jinheung and greater than 270 for IR 667-Suwon 214. 3. The ripened grain ratio was not different from main culm to first tillers of second order of main culm in Jinheung but greatly decreased from 4th tiller of first order of main culm in IR667 and the number of grain per main culm was greater in IR667 than in Jinheung indicating that yield of IR667 could be increased by increasing the number of main culm. 4. The last heading date insuring optimum ripening period appeared to be 25th in August for Jinheung and 30th in August for IR667 in Suweon.

• Journal of the Economic Geographical Society of Korea
• /
• v.15 no.3
• /
• pp.437-455
• /
• 2012

Korea has recently constructed a number of renewable photovoltaic power plants in Jeolla province as an effort to provide environment-friendly energy. However, several problems appeared in the power plant locations because they were not appropriately chosen ignoring social-environmental perspectives. Consequently, locations of both currently existing photovoltaic power plants require an social and environmental evaluations. This study aims to provide appropriate photovoltaic power plants locations and evaluation of current photovoltaic power plants in Jeolla province. By presenting location analysis of photovoltaic power plants, this study would minimize environmental and social side effects regarding photovoltaic power plants. Kriging and Analytic Network Process (ANP) are applied as methodology. ANP generates correct weights in combining spatial data, so that the result would present optimal locations. In addition environmentally sensitive regions were excluded in the analysis process. The results show that South and West coastal areas have a number of appropriate locations for photovoltaic power plants. In addition, evaluating currently running photovoltaic power plant locations, total 23 out 81 are turned out to be inappropriately located. This study is expected to contribute avoiding social and environmental conflicts in photovoltaic power plant locations and present criteria in evaluating photovoltaic power plants.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.44.3-45
• /
• 2017

To date, luminous quasars at z ~ 6 have been found to be in maximal accretion with the Eddington ratios, ${\lambda}Edd$ ~ 1, suggesting enhanced nuclear activities in the early universe. However, this may not be the whole picture of supermassive black hole (SMBH) growth since previous studies have not reached on faint quasars that are more likely to harbor SMBHs with low ${\lambda}Edd$. To understand the accretion activities in quasars at high redshift, we obtained the deep near-infrared (NIR) spectrum of a quasar, IMS J2204+0112, one of the few faintest quasars that have been identified at z ~ 6. From the NIR spectrum, we find that IMS J2204+0112 harbors a SMBH with about a billion solar mass, with ${\log}({\lambda}Edd)=-0.91$. This is the lowest accretion rate found so far for quasars at z ~ 6, but a common value among quasars at z ~ 2. The inclusion of this object in the ${\lambda}Edd$ analysis gives the intrinsic ${\lambda}Edd$ distribution of z ~ 6 quasars, which is lower than previous results that are based on bright quasars, but it is still higher than ${\lambda}Edd$ of z ~ 2 quasars. Although the number statistics needs to be improved in future, the low peak ${\lambda}Edd$ value is consistent with the SMBH growth from a massive black hole seed (~ 105 Msun) or from a stellar mass black hole through short-duration super-Eddington accretion events (${\lambda}Edd$ > 10).

• Journal of Bio-Environment Control
• /
• v.19 no.1
• /
• pp.6-11
• /
• 2010

This experiment was conducted to investigate the effect of greenhouse orientation on the greenhouse environment and the growth and yield of tomato cv 'Momotaro-Yoku' in forcing culture. The photosynthetic phpton flux density (PPFD) of a.m was higher in north-south orientation than that in east-west orientation and it was opposed in the p.m. Mean PPFD of a day was higher in east-west orientation than that in north-south orientation because the light transmitting area became larger in east-west orientation with decrease of incidence angle. The PPFD at 60 cm point above ground of all furrows was poor due to shadows near plants and it was higher in north-south orientation than that in east-west orientation. The air temperature in the greenhouse was higher in east-west orientation than that in north-south orientation but there was no significant difference since mid February as solar altitude goes up. The soil temperature was some higher in east-west orientation than that in north-south orientation and there was not significant difference among ridges. In east-west orientation, as ripening was promoted, high early yield of tomato were obtained. So total yield was greater about 8% in east-west orientation than that in north-south orientation. Therefore, it was considered that east-west orientation is more advantageous than north-south orientation for forcing culture of tomato.

• Journal of Bio-Environment Control
• /
• v.24 no.4
• /
• pp.287-295
• /
• 2015

This study was conducted to find the suitability site selection for the construction of Saemangeum horticulture complex taking into account cost-effective environmental management by analyzing and comparing meteorological conditions. The study sites were regions around the Saemangeum area in which the development of an industrial complex extending 28,300 ha is planned. We collected meteorological data in 12 candidate sites and established a rating scheme and thematic maps. We selected ten themes by consulting experts using a questionnaire. Selected ten themes is Summer, 20 days max. temp. mean, Winter, 20 days min. temp. mean, Summer, 90 days temp. mean, Winter, 90 days temp. mean, Year-round, max. wind velocity, Year-round, wind velocity mean, Winter, 90 days solar radiation mean, Year-round, number of foggy days, Year-round, 1 day max. rainfall and Spring. 90 days humidity mean. And we set ratio-based weights for the evaluation parameters.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1283-1288
• /
• 1999

Effect of drying methods, such as natural solar drying, hot air drying$(at\;60^{\circ}C\;and\;105^{\circ}C)$, vacuum drying and freeze drying methods, on the quality of laver were investigated to develop optimum processing conditions for preparation of laver powder. Appreciable amount of laver pigments such as chlorophyll, carotenoid and phycobilin were lost during washing and drying process. Their loss was affected significantly by the method of drying. Among the methods tested, high temperature air drying was the worst in retaining laver pigment, while freeze drying was the best. Loss of vitamin C which was in the range of 75-99% was also affected by the method of drying. Isotherms for laver powder shelved sigmoidal shape and monomolecular layer moisture content of both laver powder(Porphyra dentata and Porphyra tenera) determined by the BET equation was 6.30%(dry basis). Laver powders prepared with Porphyra dentata and classified with 50-, 80- and 100- mesh sieves showed monomodal size distribution with the high frequency at 110-120, 100-110 and $80\;{\mu}m$, respectively, which indicated that size or laver powder was homogeneous.

• Journal of the Korean Society of Radiology
• /
• v.5 no.2
• /
• pp.97-101
• /
• 2011

In this study, the basic research verifying possibility of applications as radiology image sensor in Digital Radiography was performed, the radiology image sensor was fabricated using double layer technique tio decrease dark current. High efficiency material in substitution for a-Se have been studied as a direct method of imaging detector in Digital Radiography to decrease dark current by using Hetero junction already used as solar cell, semiconductor. Particle-In-Binder method is used to fabricate radiology image sensor because it has a lot of advantages such as fabrication convenient, high yield, suitability for large area sensor. But high leakage current is one of main problem in PIB method. To make up for the weak points, double layer technique is used, and it is considered that high efficient digital radiation sensor can be fabricated with easy and convenient process. In this study, electrical properties such as leakage current, sensitivity is measured to evaluate double layer radiation sensor material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.49-49
• /
• 2009

최근 범세계적인 그린에너지 정책에 관련해 화석연료를 대체할 수 있는 수소, 풍력, 태양광 등의 대체 에너지에 대한 관심이 고조되고 있다. 이러한 여러 대체에너지 중에서도 태양광을 전기에너지로 변환하는 태양전지에 관한 연구가 집중되고 있다. 태양전지는 구조적으로 단순하고 제조 공정도 비교적 간단하지만, 보다 널리 보급되기 위해서는 경제성 향상이라는 문제점을 해결해야 한다. 이를 위해서는 기존의 실리콘 태양전지를 대체할 수 있는 신물질에 대한 연구가 필요하며, 그 중에서도 반도체 기술을 이용한 박막형 태양전지는 기존의 실리콘 태양 전지가 가지고 있는 고비용이라는 문제점을 극복할 수 있을 것으로 기대를 모으고 있다. 박막형 태양전지의 박막 재료로는 CIGS, CdTe 등이 연구되어지고 있지만, 아직까지는 기존의 실리콘 태양전지에 비해 에너지변환효율이 낮은 이유로 인해 실용화가 많이 이루어지지 못하고 있는 것이 사실이다. 이러한 박막형 태양전지의 재료들 중에서도 CdTe는 이종접합 박막형 태양전지에 흡광층으로 사용되는 것으로 상온에서 1.45eV 정도의 밴드갭(band gap) 에너지를 갖는 II-VI족 화합물반도체로써 태양광 스펙트럼과 잘 맞는 이상적인 밴드랩 에너지와 높은 광흡수도 때문에 박막형 태양전지로 가장 주목을 받고 있다. CdTe 박막의 제조 방법으로는 진공증착법(vacuum evaporation), 전착법(electrodeposition), 스퍼터링법(sputtering) 등이 있지만 본 연구에서는 스퍼터링법을 이용하여 박막을 증착하였다. 이상과 같이 증착된 CdTe 박막을 화학적기계적연마(CMP, chemical mechanical polishing) 공정을 적용시킴으로써, 태양전지의 에너지변환효율에 직접적인 영향을 끼칠 수 있는 CdTe 박막의 물리적, 전기적 특성들의 변화를 연구하기 위한 선행 연구를 진행하였다. 특히 본 연구에서는 CdTe 박막의 화학적 기계적 연마 특성을 분석하여 정규화를 통한 모델링을 수행하였다. 또한 화학적기계적연마 공정 전과 후의 표면 특성을 관찰하기 위해 SEM(scanning electron microscopy)과 AFM(atomic forced microscope)를 이용하였으며, 구조적 특성 관찰을 XRD(X-ray diffraction)를 사용하여 실험을 수행하였다.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.11
• /
• pp.1555-1561
• /
• 2016

Shank skin color of Korean native chicken (KNC) shows large color variations. It varies from white, yellow, green, bluish or grey to black, whilst in the majority of European breeds the shanks are typically yellow-colored. Three shank skin color-related traits (i.e., lightness [$L^*$], redness [$a^*$], and yellowness [$b^*$]) were measured by a spectrophotometer in 585 progeny from 68 nuclear families in the KNC resource population. We performed genome scan linkage analysis to identify loci that affect quantitatively measured shank skin color traits in KNC. All these birds were genotyped with 167 DNA markers located throughout the 26 autosomes. The SOLAR program was used to conduct multipoint variance-component quantitative trait locus (QTL) analyses. We detected a major QTL that affects $b^*$ value (logarithm of odds [LOD] = 47.5, $p=1.60{\times}10^{-49}$) on GGA24 (GGA for Gallus gallus). At the same location, we also detected a QTL that influences $a^*$ value (LOD = 14.2, $p=6.14{\times}10^{-16}$). Additionally, beta-carotene dioxygenase 2 (BCDO2), the obvious positional candidate gene under the linkage peaks on GGA24, was investigated by the two association tests: i.e., measured genotype association (MGA) and quantitative transmission disequilibrium test (QTDT). Significant associations were detected between BCDO2 g.9367 A>C and $a^*$ ($P_{MGA}=1.69{\times}10^{-28}$; $P_{QTDT}=2.40{\times}10^{-25}$). The strongest associations were between BCDO2 g.9367 A>C and $b^*$ ($P_{MGA}=3.56{\times}10^{-66}$; $P_{QTDT}=1.68{\times}10^{-65}$). However, linkage analyses conditional on the single nucleotide polymorphism indicated that other functional variants should exist. Taken together, we demonstrate for the first time the linkage and association between the BCDO2 locus on GGA24 and quantitatively measured shank skin color traits in KNC.