• Korean Journal of Materials Research
• /
• v.27 no.4
• /
• pp.216-220
• /
• 2017

The effect of electron beam (EB) irradiation on the electrical properties of Zn-Sn-O (ZTO) thin films fabricated using a sol-gel process was investigated. As the EB dose increased, the saturation mobility of ZTO thin film transistors (TFTs) was found to slightly decrease, and the subthreshold swing and on/off ratio degenerated. X-ray photoelectron spectroscopy analysis of the O 1s core level showed that the relative area of oxygen vacancies ($V_O$) increased from 10.35 to 12.56 % as the EB dose increased from 0 to $7.5{\times}10^{16}electrons/cm^2$. Also, spectroscopic ellipsometry analysis showed that the optical band gap varied from 3.53 to 3.96 eV with increasing EB dose. From the results of the electrical property and XPS analyses of the ZTO TFTs, it was found that the electrical characteristic of the ZTO thin films changed from semiconductor to conductor with increasing EB dose. It is thought that the electrical property change is due to the formation of defect sites like oxygen vacancies.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.366-366
• /
• 2011

이성분 산화물인 ZnO/$TiO_2$ core-shell 나노입자는 core-shell 구조의 특성과 이성분 산화물의 상호작용에 의해서 염료감응형 태양전지의 효율향상을 기대할 수 있다. Znic acetate($Zn_2(CH_3COO)$)와 Titanium(IV) butoxide($Ti(OBu)_4$)를 이용하여 ZnO 나노입자를 수열합성하고 그 주의에 $TiO_2$을 가수분해 반응을 이용하여 둘러싸는 core-shell형태의 물질을 합성하였다. 그 이후 결정성 및 유기물 제거를 위해서 4시간 동안 고온에서 소성하였다. SEM 결과에 따르면 소성 온도를 600도까지 증가시키면 ZnO의 경우 나노입자의 크기가 증가하는 경향을 확인하였다. 하지만 core-shell의 경우는 ZnO의 뭉침현상을 $TiO_2$이 방해하여 초기합성된 크기와 동일한 크기를 유지하는 것을 확인하였다. 또한 XRD 결과에 따르면 주변에 형성된 $TiO_2$ 이외에 $Zn_2TiO_4$의 spinel 구조를 가지는 물질이 합성되는 것을 확인할 수 있었다. 합성된 core-shell 구조의 나노입자는 약 40~50 nm의 크기를 가지고 600도에서 소성된 입자의 경우 산소 정공이 거의 없는 약 3 eV의 밴드갭을 가지는 물질로 합성이 되었다. Core-shell 나노입자의 경우 염료 감응형 태양전지의 반도체 물질로 응용 가능할 것으로 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.294-302
• /
• 2023

Ni-Mn-Zn ferrite, Ni_0.5-xMn_xZn_0.5Fe₂O₄ (0 ≤ x ≤ 0.5), was synthesized using the sol-gel method to investigate the crystal structure, microstructure, magnetic properties, high-frequency characteristics, and electromagnetic (EM) wave absorption characteristics as a function of Mn substitution. As the Mn content increased, a continuous decrease in saturation magnetization (M_S) was observed with little change in coercivity (H_C). Samples for each composition (x) exhibited strong EM wave absorption performance with first and second strong EM wave absorption regions satisfying minimum reflection loss, RL_min < -40 dB in the 1.5~2.5, 6~11 GHz range, respectively. The EM wave absorption in Ni-Mn-Zn ferrite depends on magnetic loss, and adjusting µ' and µ'' spectra by Mn substitution or H field allows control of the EM wave absorption frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.457-460
• /
• 2006

Y doped zinc oxide (YZO) thin films were deposited on F doped $SnO_2$ (FTO) glass substrate by sol-gel method using the spin-coating system. A homogeneous and stable solution was prepared by dissolving acetate in the solution added diethanolamine as sol-gel stabilizer. YZO films were obtained after preheated on the hot-plate for 5minute before each coating; the number of coating was 3 times. After the coating of last step, annealing of YZO films performed at $450^{\circ}C$ for 30 minute. In order to confirming of a ultraviolet ray interruption and down-conversion effects, optical properties of YZO films, transmission spectrum and fluorescent spectrum were used. Also, for understanding the obtained results by experiment, the elestronic state of YZO was calculated using the density functional theory The results obtained by experiment were compared with calculated structure. The detail of electronic structure was obtained by the discrete variational Xa (DV-Xa) method, which is a sort of molecular orbital full potential method. The density of state and energy levels of dopant element were shown and discussed in association with optical properties.

• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.136-141
• /
• 2010

ACF/ZnO photocatalyst was synthesized by a sol-gel method using activated carbon fiber (ACF) and Zn $(NO_3)_2$ as precursors. Samples were characterized by Brunauer-Emmett-Teller measurements (BET), scanning electron microscope (SEM), X-ray diffraction (XRD), and energy dispersive X-ray (EDX). The XRD results showed that ACF/ZnO composites only included a hexagonal phase by heat-treated temperature at $400^{\circ}C$, $500^{\circ}C$, $600^{\circ}C$, and $700^{\circ}C$. The SEM analysis revealed that the ACF/ZnO composites did not exhibit any morphological changes of the catalyst surface according to the different heat-treated temperatures. The photocatalytic activity of the samples was tested for degradation of methylene blue (MB) solutions under ultraviolet (UV) light and ultrasonication respectively. The results showed that the photocatalytic activity of ACF/ZnO composites heat-treated at $500^{\circ}C$ was higher than other samples, which is ascribed to the fine distribution of ZnO particles on the surface of the ACF. In addition, an ultrasound of low power (50 W) was used as an irradiation source to successfully induce ACF/ZnO composites to perform sonocatalytic degradation of MB. Results indicated that the sonocatalytic method in the presence of ACF/ZnO composites is an advisable choice for the treatments of organic dyes.

• Current Photovoltaic Research
• /
• v.1 no.1
• /
• pp.59-62
• /
• 2013

We investigated the effects of ZnO thin film deposition methods on the performance of inverted polymer solar cells with a structure of ITO/ZnO/P3HT:PCBM/MoO3/Al. The ZnO thin films were deposited by various methods (spin coating of nanoparticles, sol-gel process, atomic layer deposition) and their morphology was analyzed by atomic force microscopy (AFM). The device with ZnO nanoparticle thin films showed the highest power conversion efficiency of 3 % with low series resistance and high shunt resistance. The superior performance of the device with the ZnO nanoparticle layer is attributed to better electron extraction capability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.190-190
• /
• 2010

Zinc oxide is the most attractive material due to the large direct band gap (3.37 eV), excellent chemical and thermal stability, and large exciton binding energy (60 meV). Recently, ZnO nanorods were used as the high efficient antireflection coating layer of solar cells based on silicon (Si). In this reports, we studied the effects of rapid thermal annealing (RTA) treatment on optical properties of ZnO nanorods. For fabrication of ZnO nanorods, there are many methods such as hydrothermal method, sol-gel method, and metal organic chemical vapor deposition method. Among of them, we used the conventional wet chemical method which is simple and low temperature growth. In order to synthesize the ZnO nanorods, the ZnO films were deposited on Si substrate by RF magnetron sputtering at room temperature and the samples were dipped to aqua solution containing the zinc nitrate and hexamethylentetramines (HMT). The synthesis process was achieved in keeping with temperature of $90-95^{\circ}C$ and under constant stirring. The morphology of ZnO nanorods on glass and Si was characterized by scanning electron microscopy. For the analysis of antireflection performance, the reflectance and transmittance were measured by spectrophotometer. And for analyzing the effects of RTA treatment on ZnO nanorods, crystalline properties were investigated by X-ray diffraction measurements and optical properties was estimated by photoluminescence spectra.

• Journal of Magnetics
• /
• v.15 no.4
• /
• pp.159-164
• /
• 2010

The Zn, Co and Ni substituted manganese ferrite powders, $Mn_{1-x}$(Zn, Co, Ni)$_xFe_2O_4$, were fabricated by the solgel method, and their crystallographic and magnetic properties were studied. The Zn substituted manganese ferrite, $Zn_{0.2}Mn_{0.8}Fe_2O_4$, had a single spinel structure above $400^{\circ}C$, and the size of the particles of the ferrite powder increased when the annealing temperature was increased. Above $500^{\circ}C$, all the $Mn_{1-x}$(Zn, Co, Ni)$_xFe_2O_4$ ferrite had a single spinel structure and the lattice constants decreased with an increasing substitution of Zn, Co, and Ni in $Mn_{1-x}$(Zn, Co, Ni)$_xFe_2O_4$. The Mossbauer spectra of $Mn_{1-x}Zn_xFe_2O_4$ (0.0$\leq$x$\leq$0.4) could be fitted as the superposition of two Zeeman sextets due to the tetrahedral and octahedral sites of the $Fe^{3+}$ ions. For x = 0.6 and 0.8 they showed two Zeeman sextets and a single quadrupole doublet, which indicated they were ferrimagnetic and paramagnetic. And for x = 1.0 spectrum showed a doublet due to a paramagnetic phase. For the Co and Ni substituted manganese ferrite powders, all the Mossbauer spectra could be fitted as the superposition of two Zeeman sextets due to the tetrahedral and octahedral sites of the $Fe^{3+}$ ions. The variation of the Mossbauer parameters are also discussed with substituted Zn, Co and Ni ions. The increment of the saturation magnetization up to x = 0.6 in $Mn_{1-x}Co_xFe_2O_4$ could be qualitatively explained using the site distribution and the spin magnetic moment of substituted ions. The saturation magnetization and coercivity of the $Mn_{1-x}$(Zn, Co, Ni)$_xFe_2O_4$ (x = 0.4) ferrite powders were also compared with pure $MnFe_2O_4$.

• Journal of Magnetics
• /
• v.10 no.3
• /
• pp.84-88
• /
• 2005

Nanoparticles $Ni_{0.7}Zn_{0.3}Fe_2O_4$ is fabricated by a sol-gel method. The magnetic and structural properties of powders were investigated with XRD, SEM, $M\ddot{o}ssbauer$ spectroscopy, and VSM. $Ni_{0.7}Zn_{0.3}Fe_2O_4$ powders annealed at $300^{\circ}C$ have a spinel structure and behaved superparamagnetically. The estimated size of $Ni_{0.7}Zn_{0.3}Fe_2O_4$ nanoparticle is about 11 nm. $Ni_{0.7}Zn_{0.3}Fe_2O_4$ annealed at 400 and $500^{\circ}C$ has a typical spinel structure and is ferrimagnetic in nature. The isomer shifts indicate that the iron ions were ferric at the tetrahedral (A) and the octahedral (B). Blocking temperature $(T_B)\;of\;Ni_{0.7}Zn_{0.3}Fe_2O_4$ nanoparticle is about 260 K. The magnetic anisotropy constant of $Ni_{0.7}Zn_{0.3}Fe_2O_4$ annealed $300^{\circ}C$ were calculated to be $1.7X10^6\;ergs/cm^3$. Also, temperature of the sample increased up to $43^{\circ}C$ within 7 minutes under AC magnetic field of 7 MHz.

• Tribology and Lubricants
• /
• v.24 no.2
• /
• pp.77-81
• /
• 2008

In this work, ramp loading scratch method was used to evaluate the scratch characteristics of HDD media and ZnO thin films. Commercially available HDD media and ZnO thin films grown on silicon(100) substrate by sol-gel method were used. As for the ZnO films, the effects of annealing temperature after the film deposition process were also investigated. A custom built scratch tester was used to scratch the specimen under a ramp loading condition. The scratch track formed by ramp loading was measured by optical microscope and Atomic Force Microscopy (AFM). The wear depth and width were used to assess the scratch characteristics of the HDD Media and ZnO thin films. The results showed that ZnO film annealed at $800^{\circ}C$ had the best scratch resistance property. Also, the HDD media showed overall better scratch resistance than the ZnO films.