• Journal of Electrochemical Science and Technology
• /
• v.2 no.2
• /
• pp.103-109
• /
• 2011

Nanocrystalline $LiFePO_4$ powders were prepared at 660-$670^{\circ}C$ in an Ar atmosphere using two different synthetic routes, solid-state and sol-gel. Both materials showed well-developed XRD patterns without any impurity peaks. Particles composed in the range of 200-300 nm from the solid-state method, and 50-100 nm from the sol-gel method, were confirmed through scanning electron microscopy and dynamic light scattering. The $LiFePO_4$ obtained by the sol-gel method offered a high discharge capacity (153 mAh/g) and stable discharge behavior, even at elevated temperatures (50 and $60^{\circ}C$), whereas poor electrochemical performance was observed from the solid-state method. Rate capability studies for sol gel-derived $LiFePO_4$ ranged from 0.2 to 30 C, which revealed excellent retention over 70 cycles with a 99.9% capacity.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.

• Textile Coloration and Finishing
• /
• v.6 no.1
• /
• pp.49-53
• /
• 1994

The transparent coloration of glasses has been successfully achieved by coated glass surface with squarylium dye by the sol-gel colored coating method. Treatment of sol-gel colored coating layer with HCI(g) greatly decreases the absorbance at λ$_{max}$, that increases exposure to $NH_{3}$(g) and the reversible color-colorless responce was extremely rapid.d.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.52.1-52.1
• /
• 2007

• Journal of the Korean Ceramic Society
• /
• v.36 no.11
• /
• pp.1274-1279
• /
• 1999

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.555-558
• /
• 2004

In this paper, the variable producing conditions of YBCO superconducting powder by use of sol-gel method was investigated. YBCO superconducting powder which was prepared by sol-gel method was shown the characteristic gel formation, particle size and its properties under variable preparation conditions, such as pH, drying and processing time, and powder heat treatment, etc.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1301-1310
• /
• 1996

Generally it requires high sintering temperatures more than 135$0^{\circ}C$ to make semiconductive BaTiO3 ceramics. Also it is very difficult to achieve a homogeneous mixing in solid-state reaction method. Therefore the liquid phase distributed to non-uniform dilute the characteristics of PTCR. In order to improve the uniformity this study is used the sol-gel coating method. Using this method we studied the new manufacturing process that had a high reproducibility and mass production capability. Tetraethyl orthosilicate (TEOS) was used as a source of Si. The semiconductive BaTiO3 ceramics which was produced by sol-gel method for the SiO2 addition and sintered between 124$0^{\circ}C$ and 130$0^{\circ}C$ showed almost same resistivity at room temperature among 125$0^{\circ}C$ and 130$0^{\circ}C$. As the results We could be sintered the semiconducting BaTiO3 ceramics at lower temperature even at 125$0^{\circ}C$ maintaining the same specific resistivity ratio ($\rho$max/$\rho$min) at 130$0^{\circ}C$. The specific resistivity both below and above the Curie temperature were increased by slow cooling and the steepness of the plots in the reasion of transition from low to high resistance increased as the cooling rate decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.557-560
• /
• 2003

The submicron $YBa_2Cu_3O_x$ powder was prepared by the sol-gel method. The particle size is distributed from 0.2 to $1.0\;{\mu}m$, which benefits to eliminate the micro-cracks formed in the $YBa_2Cu_3O_x$ films deposited by electrophoresis. The powder was single phase of $YBa_2Cu_3O_x$ examined by X-ray diffraction. In the sol-gel process the citrate gel was formed from citric acid and nitrate solution of $Y_2O_3$, $Ba(NO_3)O_2$ and CuO. When pH values were adjusted to $6.4{\sim}6.7,\;Ba(NO_3)O_2$ could be dissolved in the citrate solution completely. Appropriate evaporative temperature of the sol-gel formation is discussed. After the heat treatment the transition temperature($T_c$) and critical current density($J_c$) of the $YBa_2Cu_3O_x$ samples made of the submicron powder were measured.

• Journal of Sensor Science and Technology
• /
• v.19 no.3
• /
• pp.202-208
• /
• 2010

This study examined the dependency of crystalline orientation and electric properties of sol-gel PZT film on hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The PZT thin films were prepared by using 2-Methoxyethanol-based sol-gel method and spin-coating on Pt/Ti/$SiO_2$/Si substrates. The 1-${\mu}m$-thick PZT films were coated and then fired in a furnace by direct insert method. The highly (111) oriented PZT film of pure perovskite structure could be obtained. We could control the degree of orientation by various parameters such as hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The highest measured remanent polarization, dielectric constant and piezoelectric coefficient are $24.16\;{\mu}C/cm^2$, 2808, and 159 pC/N, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.552-555
• /
• 2008

The purpose of this study was to find a best condition of fabricating lead zirconate thin film by sol-gel method, especially to find mol ratio and post annealing temperature. Lead zirconate thin film was made by spin coating method. The ratios of Pb and Zr of precursors were 1:0.8, 1:1.0, and 1:1.2. Annealing temperature of films were $600^{\circ}C$, $700^{\circ}C$, and $800^{\circ}C$ for 1 minute. Crystal structure was observed from XRD and antiferroelectricity was observed from hysteresis curves. The optimum mol ratio of Pb:Zr is 1:0.8 and annealing temperature is $800^{\circ}C$.